- DL manuals
- Goldine Controls
- Control Systems
- Aqua Solar AQ-SOL-LV
- Operation Manuals
Goldine Controls Aqua Solar AQ-SOL-LV Operation Manuals - Aq-Sol-Lv-Tc
7
Booster Pump
Pool Sweep
Filter Pump
240
VAC
240
VAC
Filter
Pump
Solar
Booster
Pump
Aqua Solar
(AQ-SOL-LV-TC)
AQ-SOL-LV-TC
with filter pump & booster pump relays
NOTES:
1) Do not use Aqua Solar terminal block as a junction for pump wiring.
2) Most codes require that each pump be on a separate circuit.
Summary of Aqua Solar AQ-SOL-LV
Page 1
Electronic solar control center operation and installation manual for models aq-sol-lv aq-sol-lv-tc aq-sol-lv-sp a a a a a qua qua qua qua qua s s s s s olar olar olar olar olar t m ldline controls inc. G.
Page 2: Save These Instructions
Important safety instructions when using this electrical equipment, basic safety precautions should always be followed, including the following: • read and follow all instructions • disconnect all ac power during installation. • warning – to reduce the risk of injury do not permit children to use th...
Page 3: Table of Contents
Table of contents specifications specifications specifications specifications specifications specifications specifications specifications specifications specifications ......................................................................1 operation operation operation operation operation controls c...
Page 4: Specifications
1 aqua solar digital solar control system the aqua solar digital solar control system is a differential temperature control for solar heating of pools, spas, and hot tubs. The aqua solar is available in 3 models; aq-sol-lv, aq-sol-lv-tc and aq-sol-lv-sp. These models provide differential temperature...
Page 5: Operation
Operation the aqua solar is a fully automatic solar heating control which requires minimal set up or adjustment under normal operating conditions. Typically the following is re- quired: 1. Set the main switch to auto 2. Set the “desired temperature” knob to the desired temperature for the pool 3. Se...
Page 6
3 time clock -- manual control the manual control can override the timer and is located at approximately the 4 o’clock position. “1” (up) - pump on “ ” (center) - timer controls pump “0” (down) - pump off note: if the solar override function is enabled, then the aqua solar may keep the filter pump r...
Page 7: Installation
4 installation mounting the aqua solar is designed for outdoor use. Mount the enclosure vertically with the knockouts facing downward. For safety, the aqua solar must be a minimum of 5 feet (horizontally) from the pool or spa. Power input turn off power at circuit breaker before wiring. Follow nec a...
Page 8: Sensor Mounting and Wiring
Sensor mounting and wiring most installations use a goldline "pc" type sensor for both the "solar" sensor and "pool" sensors. The "aux" sensor is required for optional recirculate freeze protection (see description of this function on page 9). Otherwise, the "aux" sensor can simply display the ambie...
Page 9: Aq-Sol-Lv
6 booster pump pool sweep filter pump ground pool sweep timer contactor (240 vac coil) 120/240 vac 240 vac filter pump timer pool filter pump pool sweep pump aqua solar (aq-sol-lv) aq-sol-lv with solar override & pool sweep interlock be careful not to cross phases on filter pump wiring 240 vac boost...
Page 10: Aq-Sol-Lv-Tc
7 booster pump pool sweep filter pump 240 vac 240 vac filter pump solar booster pump aqua solar (aq-sol-lv-tc) aq-sol-lv-tc with filter pump & booster pump relays notes: 1) do not use aqua solar terminal block as a junction for pump wiring. 2) most codes require that each pump be on a separate circu...
Page 11: Aq-Sol-Lv-Tc
8 booster pump pool sweep filter pump 240 vac filter pump sweep pump aqua solar (aq-sol-lv-tc) aq-sol-lv-tc with filter pump & pool sweep relays notes: 1) do not use aqua solar terminal block as a junction for pump wiring. 2) most codes require that each pump be on a separate circuit. 3) aqua solar ...
Page 12: Jumper Settings
9 jumper settings the jumpers that enable/disable optional control features are located on the right side of the main circuit board (see page 4). The factory default for all functions is "dis- abled" (each jumper will be on a single pin). To "enable" a function, simply take the designated jumper and...
Page 13: Troubleshooting
10 troubleshooting 1. "power" led off: check main power circuit breakers. Check to see if the aqua solar power is connected to the load side of the filter pump timer, in which case the aqua solar will only be on when the filter pump is on. Lastly, check the internal fuse which is located on the righ...
Page 14: Technical Help
11 the back cover to check the "pool" sensor with a voltmeter (you don't need to disconnect the sensor). Alternatively, you can disconnect the sensor and measure the sensor resistance. Replace the sensor or fix the wiring as required. If the sensor and wiring are both good, then the main circuit pcb...
Page 15
12 limited warranty - solar controls limited warranty - solar controls limited warranty - solar controls limited warranty - solar controls limited warranty - solar controls this warranty statement is applicable to all solar control products manufactured by goldline controls, inc., previously known a...
Page 16
092008b temperature/resistance /voltage all goldline controls use a 10k thermistor sensors. When disconnected from the control, the sensor will read 10k ohms at 25ºc/77ºf. Refer to the chart below for the resistance at other temperatures. For a given temperature, the resistance reading should be acc...