H2O Audio iRiver 300 Series User Instruction Manual

Manual is about: h2o Audio Waterproof Carrying Case for the iRiver iFP-700 Series User Instruction Manual

Summary of iRiver 300 Series

  • Page 1

    Copyright notice: this owner’s manual is copyrighted, all rights reserved. It may not, in whole or in part, be copied, photocopied, reproduced, translated, or formed into any electronic format without prior consent in writing from diver entertainment systems inc. Iriver is a registered trademark of ...

  • Page 2

    Fcc certification: this device complies with part 15 of the fcc rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, received, including interference that may cause undesired operation. Note...

  • Page 3

    Important warning: pay special attention to these labels: warning: could cause injury to the user. Caution: could cause damage to the product and/or injury to the user. Read this manual carefully. If you have any questions please contact your nearest dealer or customer support prior to use. Improper...

  • Page 4

    Leak test: before utilizing the system for the first time, it is highly recommended to perform a 'leak test’. Follow the instructions below, but do not install the mp3 player inside the housing for the leak test. 1. Visually inspect the main housing seal by opening the unit. Verify the seal is seate...

  • Page 5

    O-ring preparation: 1. Gently remove the o-ring with the remover. Be careful not to stretch the o-ring caution: never use a sharp or metal object to remove o-rings as they damage the o-ring or the o-ring groove contact surface. Use only the o-ring remover tool included in the packaging. 2. Check the...

  • Page 6

    General storage procedures: for long-term storage, remove o-ring and store out of direct sunlight. If the o-ring will not be used for a long period of time, remove from it the housing and store in a plastic bag out of direct sunlight. If the o- ring is stored in a dry environment for a long period o...

  • Page 7

    Housing operations: open the housing step 1: pull out the tab step 2: rotate the dial counterclockwise closing the housing step 1: -rotate the dial clockwise until both halves of the housing are fully closed. Step 2: push in the small locking tab. Caution: do not force the lid closed. If you feel re...

  • Page 8: The Mp3 Player Volume Level

    Lever 2: volume button 4: amplifier power on/off caution: this device provides powerful amplification of the audio signal beyond the normal output of standard stereo devices. This system is specifically engineered for underwater use to enhance fidelity at depth. This power amplifier is powerful and ...

  • Page 9

    Installing & replacing amplifier battery: step 3: open housing caution: completely dry the inside of any moisture step 4: remove and unplug the mp3 player step 1: wipe exterior and make sure it is dry step 2: turn off the amplifier.

  • Page 10

    Installing the mp3 player: caution: before opening be sure to rinse the sealed system in fresh water. Before installing the mp3 player, make sure the housing interior is dry. Moisture in the housing can cause damage to the electronics. Step 3: plug stereo adapter into mp3 player note: some mp3 playe...

  • Page 11

    Make sure the o-ring is partially squeezed, sealing the gap between the housing front and rear halves. If this contact line is not uniform, there is a good chance the housing will flood. Therefore, open the housing, reseat the o-ring and/or remove the contaminants as necessary. Step 5: close the lid...

  • Page 12

    Step 12: turn on the amplifier using the external button. The led will turn on. Step 11: insert and connect the mp3 player step 7: insert a new & dry 9-volt alkaline battery. Caution: visually inspect the inside to make sure it is dry. Step 5: push up step 6: slide out to open step 8: slide in step ...

  • Page 13

    Removing the mp3 player: step 2: wipe down the exterior with clean fresh water step 3: wipe the unit dry step 1: turn off the amplifier step 5: turn housing to side and let mp3 player slide out into your palm step 6: unplug the stereo adapter step 7: remove the mp3 player step 4: carefully open the ...

  • Page 14: Installing The Stereo Jack:

    Step 2: plug connector into mp3 player jack note: make sure you plug the connector all the way into the stereo jack step 1: line up connector with mp3 player stereo jack note: make sure you plug the connector into the stereo jack. Some of the higher end 300 series also includes an input jack for a r...

  • Page 15

    Speaker amplifier operations: speaker mask strap operation: care must be taken when handling the speakers. Do not let the speakers hang freely from the housing. Maintain control of the speakers at all times. Caution: failure to maintain control of the speakers during handling may result in damage to...

  • Page 16

    Removing/replacing the speaker clip: caution: make sure that you are holding the mask on your face when entering the water. The speakers may try to pull the mask off the face when entering the water, so pay special attention to keeping the mask on your face. To replace the clip onto the speaker: 1. ...

  • Page 17

    Limited warranty coverage: warranty limitations: diver entertainment systems inc. (des) guarantees, to the original purchaser only, that the equipment purchased (excluding the mp3 player) is free of defects in material and/or under normal recreational scuba use for a period of one year (1) from date...

  • Page 18

    Warranty correspondence: a copy of the original sales receipt and a copy of the owner’s portion of the warranty card must accompany all correspondence regarding the equipment covered by this warranty agreement or in direct reference to this warranty. Contacting customer support: customer services is...