H3c s3100 series ethernet switches installation manual hangzhou h3c technologies co., ltd. Http://www.H3c.Com manual version: 20080115-c-1.04.
Copyright © 2007-2008, hangzhou h3c technologies co., ltd. And its licensors all rights reserved no part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of hangzhou h3c technologies co., ltd. Trademarks h3c, , aolynk, , h 3 care, , top g, , i...
About this manual related documentation in addition to this manual, each h3c s3100 series ethernet switches documentation set includes the following: manual description h3c s3100 series ethernet switches operation manual it is used for assisting the users in data configurations and typical applicati...
Chapter contents 7 appendix lightning protection of the switch introduces lightning protection of s3100 series ethernet switches. Conventions the manual uses the following conventions: i. Gui conventions convention description button names are inside angle brackets. For example, click . [ ] window n...
Installation manual h3c s3100 series ethernet switches table of contents i table of contents chapter 1 product introduction ................................................................................................... 1-1 1.1 overview ..............................................................
Installation manual h3c s3100 series ethernet switches table of contents ii chapter 3 installation .................................................................................................................... 3-1 3.1 installing a switch ...........................................................
Installation manual h3c s3100 series ethernet switches table of contents iii.
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-1 chapter 1 product introduction 1.1 overview the h3c s3100 series ethernet switches are high-performance, high-density, easy-to-install, nms-manageable intelligent ethernet switches which support wire-speed laye...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-2 table 1-3 h3c s3100-c-si series ethernet switches model power input number of 10/100 mbps electrical ports number of expansion slots number of console ports s3100-26c-si 24 2 s3100-16c-si 16 2 s3100-8c-si ac in...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-3 table 1-5 models of the h3c s3100-c-epon-ei series ethernet switches model power input number of 10/100 mbps electrical ports number of 1000 mbps uplink pon ports number of expansion slots number of console por...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-4 ii. Rear panel figure 1-2 shows the rear panel of an s3100-26t-si ethernet switch. (1) ac power socket (2) grounding screw figure 1-2 rear panel of an s3100-26t-si ethernet switch iii. Power system s3100-26t-si...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-5 note: for details about leds on the front panel, refer to section 1.4.1 “front panel leds of the s3100-si/s3100-tp-pwr-ei/s3100-c-epon-ei series”. Ii. Rear panel figure 1-4 shows the rear panel of an s3100-16t-...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-6 (1) power led (2) a/l led (3) d/s led (4) port status led, left (yellow) (5) port status led, right (green) (6) 10/100 base-tx port (7) 10/100/1000 base-t port (8) console port (9) link led (green) (10) act led...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-7 1.2.4 s3100-26c-si both ac-powered switches and dc-powered switches are available to this model. I. Front panel s3100-26c-si ethernet switches each provide twenty-four auto-sensing 10/100base-tx ethernet ports,...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-8 figure 1-9 shows the rear panel of an s3100-26c-si dc-powered ethernet switch. (1) dc input terminal block (2) grounding screw figure 1-9 rear panel of an s3100-26c-si dc-powered ethernet switch iii. Power syst...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-9 note: z with a poe card inserted in one expansion slot, an s3100-16c-si ethernet switch will be a powered device (pd). In this case, the other expansion slot becomes unavailable. Z for details about leds on the...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-10 1.2.6 s3100-8c-si both ac-powered switches and dc-powered switches are available to this model. I. Front panel s3100-8c-si ethernet switches each provide eight auto-sensing 10/100base-tx ethernet ports, one ex...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-11 figure 1-15 shows the rear panel of an s3100-8c-si dc-powered ethernet switch. (1) dc input terminal block (2) grounding screw figure 1-15 rear panel of an s3100-8c-si dc-powered ethernet switch iii. Power sys...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-12 (1) (2) (4) (5) (6) (7) (8) (3) (7) (1) auto-sensing 10/100base-tx port speed led (green) (2) auto-sensing 10/100base-tx port (3) combo port speed led (green) (4) auto-sensing 10/100/1000base-t port (5) consol...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-13 z rated voltage range: 100 vac to 240 vac, 50 hz/60 hz z input voltage range: 90 vac to 264 vac, 47 hz to 63 hz 2) s3100-26tp-ei dc-powered ethernet switches: z rated voltage range: –48 vdc to –60 vdc z input ...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-14 ii. Rear panel figure 1-20 shows the rear panel of an s3100-16tp-ei ac-powered ethernet switch. (1) (2) (1) grounding screw (2) ac input terminal block figure 1-20 rear panel of an s3100-16tp-ei ac-powered eth...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-15 s3100-8tp-ei ethernet switches have the same front panel, as shown in figure 1-22. (1) (2) (4) (5) (6) (7) (8) (3) (7) (1) auto-sensing 10/100base-tx port speed led (green) (2) auto-sensing 10/100base-tx port ...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-16 (1) (2) (1) grounding screw (2) dc input terminal block figure 1-24 rear panel of an s3100-8tp-ei dc-powered ethernet switch iii. Power system 1) s3100-8tp-ei ac-powered ethernet switches: z rated voltage rang...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-17 (1) (2) (3) (4) (5) (6) (7) (8) (1) auto-sensing 10/100base-tx ethernet port status led (2) link led for combo port (3) console port (4) power led (pwr) (5) a/l led (6) d/s led (7) mode button (8) act led for ...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-18 note: only the recommended rps can be used for s3100-26tp-pwr-ei ethernet switches. The –48 vdc in the equipment room cannot be used directly. Otherwise, the device may be damaged. Iv. Cooling system the s3100...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-19 note: for details about leds on the front panel, refer to section 1.4.1 “front panel leds of the s3100-si/s3100-tp-pwr-ei/s3100-c-epon-ei series”. Ii. Rear panel (1) (2) (1) ac power socket (2) grounding screw...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-20 iv. Power system s3100-16tp-pwr-ei ethernet switches support ac input. Z rate voltage range: 100 vac to 240 vac, 50 hz/60 hz z input voltage range: 90 vac to 264 vac, 47 hz to 63 hz v. Cooling system the s3100...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-21 ii. Rear panel (1) (2) (1) ac power socket (2) grounding screw figure 1-31 rear panel of an s3100-8tp-pwr-ei ethernet switch iii. Side panel each s3100-8tp-pwr-ei ethernet switch provides a security slot, thro...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-22 (1): power led (pwr) (2): a/l led (3): d/s led (4): port status led, left (yellow) (5): port status led, right (green) (6): 10/100 base-tx port (7): onu module (8): console port (9): link led for the uplink po...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-23 1.3.8 s3100-16c-epon-ei i. Front panel the s3100-16c-epon-ei provides 16 x 10/100base-tx ethernet ports, one 1000 mbps uplink pon port, and one console port. Figure 1-34 shows the front panel of the s3100-16c-...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-24 iv. Cooling system the s3100-16c-epon-ei cools off naturally. 1.3.9 s3100-8c-epon-ei i. Front panel the s3100-8c-si provides 8 x 10/100base-tx ethernet ports, one 1000 mbps uplink pon port, and one console por...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-25 z rated voltage range: 100 vac to 240 vac, 50 hz/60 hz z input voltage range: 90 vac to 264 vac, 47 hz to 63 hz iv. Cooling system the s3100-8c-epon-ei cool off naturally. 1.4 introduction to front panel leds ...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-26 table 1-7 description of port status leds on s3100-si, s3100-tp-pwr-ei, and s3100-c-epon-ei series ethernet switches port status mode led port status led description blinking the port is in the active state an...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-27 1.4.2 front panel leds of the s3100-tp-ei series i. Power led table 1-9 description of the power led on the s3100-tp-ei series led mark on the panel status description on the switch is powered on. Power led po...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-28 table 1-12 description of the combo port speed led of the s3100-tp-ei series led operating port status description connected to a 1000 mbps optical module on the port is operating at 1000 mbps. 100/1000base -x...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-29 item s3100-26t-si s3100-16t-si s3100-8t-si operating temperature 0°c to 45°c (30°f to 113°f) relative humidity (noncondensing) 10% to 90% ii. S3100-c-si table 1-14 technical specifications for the s3100-c-si s...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-30 item s3100-26c-si s3100-16c-si s3100-8c-si power system both dc-powered switch and ac-powered switch are available to each model. The ac-powered switch supports only ac input, and the dc-powered switch support...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-31 1.5.2 s3100-ei series ethernet switch i. S3100-tp-ei table 1-15 technical specifications for the s3100-tp-ei series item s3100-26tp-ei s3100-16tp-ei s3100-8tp-ei physical dimensions (h × w × d) 43.6 × 440 × 16...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-32 ii. S3100-tp-pwr-ei table 1-16 technical specifications for the s3100-tp-pwr-ei series item s3100-26tp-pw r-ei s3100-16tp-pw r-ei s3100-8tp-pw r-ei physical dimensions (h × w × d) 43.6 × 440 × 420 mm (1.7 × 17...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-33 note: s3100-26tp-pwr-ei, s3100-16tp-pwr-ei, and s3100-8tp-pwr-ei ethernet switches provide an over-temperature protection mechanism. When the internal temperature exceeds 65°c (149°f), they will stop providing...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-34 item s3100-26c-epon- ei s3100-16c-epon- ei s3100-8c-epon-e i relative humidity (non-condensin g) 10% to 90% 1.6 sfp modules supported by s3100-ei ethernet switches the front panel of s3100-tp-ei and s3100-tp-p...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-35 table 1-19 onu module support of the s3100 series switch model number of onu modules required or optional onu module model s3100-8c-si 1 optional s3100-16c-si 1 optional s3100-26c-si 1 optional z 1000base-px10...
Installation manual h3c s3100 series ethernet switches chapter 1 product introduction 1-36 table 1-20 technical specifications for the onu port item specifications connector type sc number of interfaces 1 interface speed 1000 mbps medium 9/125 µm single-mode fiber maximum transmission distance z 100...
Installation manual h3c s3100 series ethernet switches chapter 2 installation preparation 2-1 chapter 2 installation preparation 2.1 precautions to avoid any device impairment and body injury resulting from improper use, please take the following precautions: z before cleaning the switch, disconnect...
Installation manual h3c s3100 series ethernet switches chapter 2 installation preparation 2-2 rustiness and corrosion of metal parts. If the relative humidity is too low, the captive screws may become loose due to the shrinking of insulation washers; in addition, electrostatic is more likely to be p...
Installation manual h3c s3100 series ethernet switches chapter 2 installation preparation 2-3 2.2.3 anti-interference requirements a switch in use may be affected by the interference from outside the system by way of capacitance coupling, inductance coupling, electromagnetic radiation, public impeda...
Installation manual h3c s3100 series ethernet switches chapter 2 installation preparation 2-4 caution: these installation tools are not shipped with s3100 series ethernet switches. You will have to prepare them beforehand..
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-1 chapter 3 installation caution: on a mounting screw of the chassis of the h3c s3100 series ethernet switches, there is a seal labeled with h3c. You must keep it intact before asking the agent to maintain the switch. Yo...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-2 table 3-2 installation method for a switch with a width less than 436 mm (17.2 in.) method depth use front mounting ears use front and rear mounting ears use front mounting ears and a tray use front mounting ears and g...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-3 (1) screw hole used to fix the mounting ear to the cabinet (use one m6 screw) figure 3-2 appearance of a rear mounting ear when you install s3100 series ethernet switches into 19-inch standard cabinets, you should sele...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-4 model physical dimensions (h × w × d) configuration type of front mounting ear configuration type of rear mounting ear s3100-2 6tp-pw r-ei 43.6 × 440 × 420 mm (1.7 × 17.3 × 16.5 in.) standard standard s3100-1 6tp-pw r-...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-5 front panel front mounting ear front square-holed bracket front mounting ear front panel front mounting ear front square-holed bracket front mounting ear figure 3-4 fix front mounting ears (2) iii. Use front mounting e...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-6 front panel screw 1 front mounting ear three installation locations for screw 1 (select one according to the actual requirement) front mounting ear screw 1 front panel screw 1 front mounting ear three installation loca...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-7 5) hold the bottom of the switch with one hand and the front part of the switch with the other hand, and push the switch into the cabinet gently, as shown in figure 3-7. Front square -holed bracket front mounting ear r...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-8 6) fix the other end of the front mounting ears to the front brackets with screws and captive nuts and ensure that front and rear mounting ears have fixed the switch in the cabinet securely, as shown in figure 3-9. Fro...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-9 note: guide rails purchased from h3c apply only to standard cabinets 1,000 mm (39.4 in.) deep. Use other supports to substitute for guide rails in the case of other cabinet depths. Z installation procedure follow these...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-10 front panel figure 3-12 install front mounting ears and guide rails 6) fix the other end of front mounting ears to the front brackets of the cabinet with m6 screws and captive nuts and ensure that the front mounting e...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-11 note: z no guide rails are delivered with the device. Z ensure a clearance of 1u (44.45 mm, namely, 1.75 inches) between devices for the purpose of heat dissipation. 3.1.2 desk mounting when a 19-inch standard cabinet...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-12 figure 3-14 screw (1) (1) (1) outside edge of anchor kit figure 3-15 anchor kit ii. Installation procedure the wall-mounting procedure is as follows: 1) as shown in figure 3-16, drill two holes 5 mm across in the wall...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-13 1.5 mm(min) x mm figure 3-16 wall mounting 4) align the two installation holes at the bottom of the switch with these two screws to hang the switch. Caution: when mounting the switch, keep the ethernet ports of the sw...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-14 (1) (2) (1) permanent magnet (2) m3*6 countersunk head screw figure 3-17 magnet and countersunk head screw ii. Installation procedure follow these steps to complete magnet mounting: 1) as shown in figure 3-18, use a p...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-15 caution: z apply magnet mounting to only the above two models. Otherwise, a falloff or mis-operation may occur. Z select the installation location carefully. In the case of poor surface, magnet mounting may not be rel...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-16 step 2: loosen the fastening screws on both sides of the expansion interface module using a screwdriver. Step 3: draw back the expansion interface module until the module is fully separated from the switch. Caution: z...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-17 both sides of the ac power input, and then set the power cord into the notch of the power cord retainer, as shown in figure 3-20. (1) (2) (3) (4) (1): rear panel (2): power cord retainer holder (3): power cord retaine...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-18 3.3.2 connecting dc power cable i. Dc power cable connection for s3100-c-si/s3100-tp-ei dc-powered ethernet switch (1) (2) (3) (4) (5) (1) screw 1 (2) screw 2 (3) rtn (+) terminal (4) neg(-) terminal (–48 v to –60 v) ...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-19 caution: z before powering on the switch, you should properly connect the grounding cable. Z the dc power cable should be less than 3 meters long. Ii. Dc power cable connection for s3100-26tp-pwr-ei ethernet switch + ...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-20 z use cable ties to bind the two power cables to the protruding part at the back of the air filter, as shown in figure 3-23. Figure 3-24 fix the rps dc power connector to the chassis 4) insert the connector into the d...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-21 3.3.3 connecting grounding cable caution: you should properly connect the switch grounding cable since it is crucial to the lightning protection and electromagnetic shield (ems) of your switch. The power input end of ...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-22 ( 1 ) ( 2 ) ( 5 ) ( 3 ) ( 4 ) ( 1 ) ( 2 ) ( 5 ) ( 3 ) ( 4 ) ( 1 ) ( 2 ) ( 5 ) ( 3 ) ( 4 ) ( 1 ) ( 2 ) ( 5 ) ( 3 ) ( 4 ) (1) power input (2) grounding screw (3) protection grounding cable (4) earth (5) angle steel figu...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-23 ( 1 ) ( 2 ) ( 4 ) ( 3 ) ( 6 ) (5 ) ( 7) (8 ) (11 ) ( 1 0 ) ( 1 ) ( 2 ) ( 4 ) ( 3 ) ( 6 ) (5 ) ( 7) (8 ) (8 ) (11 ) ( 9 ) ( 1 ) ( 2 ) ( 4 ) ( 3 ) ( 6 ) (5 ) ( 7) (8 ) (11 ) ( 1 0 ) ( 1 ) ( 2 ) ( 4 ) ( 3 ) ( 6 ) (5 ) ( ...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-24 figure 3-29 console cable table 3-5 console cable connector pinouts and mapping relation rj-45 signal direction db-9 1 rts ← 7 2 dtr ← 4 3 txd ← 3 4 cd → 1 5 gnd — 5 6 rxd → 2 7 dsr → 6 8 cts → 8 3.5.2 connecting cons...
Installation manual h3c s3100 series ethernet switches chapter 3 installation 3-25 note: when connecting a pc to a powered-on switch, you are recommended to connect the db-9 connector of the console cable to the pc before connecting the rj-45 connector to the switch. When disconnecting a pc from a p...
Installation manual h3c s3100 series ethernet switches chapter 4 first power-on 4-1 chapter 4 first power-on 4.1 establishing configuration environment the following figure shows the configuration environment you will establish: z in this environment, a terminal (a pc in this example) is connected t...
Installation manual h3c s3100 series ethernet switches chapter 4 first power-on 4-2 1) select [start/program/accessories/communications/hyperterminal] to enter the hyperterminal window, where click the icon to establish a new connection. The system displays the connection description interface, as s...
Installation manual h3c s3100 series ethernet switches chapter 4 first power-on 4-3 3) click ok> after selecting a serial port and the system pops up the following interface. In the interface, set the bits per second to 9600, data bits to 8, parity check to none, stop bits to 1, and flow control to ...
Installation manual h3c s3100 series ethernet switches chapter 4 first power-on 4-4 figure 4-6 set terminal emulation in h3c properties window 4.4 booting switch 4.4.1 checking before powering on the switch before powering on the switch, verify that: z the power cable and grounding cable are properl...
Installation manual h3c s3100 series ethernet switches chapter 4 first power-on 4-5 copyright(c) 2004-2007 hangzhou h3c technologies co., ltd. Creation date : apr 15 2007, 10:12:36 cpu clock speed : 200mhz bus clock speed : 33mhz memory size : 64mb mac address : 000fe20f3100 press ctrl-b to enter bo...
Installation manual h3c s3100 series ethernet switches chapter 4 first power-on 4-6 ................................................................... ................................................................... ................................................................... ...............
Installation manual h3c s3100 series ethernet switches chapter 4 first power-on 4-7 0. Reboot enter your choice(0-9): enter 0, the system reboots in normal mode and displays the following information: starting...... *********************************************************** * * * h3c s3100-16c-si b...
Installation manual h3c s3100 series ethernet switches chapter 4 first power-on 4-8 phy selftest...............................Ok! Please check port leds...............Finished! User interface aux0 is available. Press enter to get started. The appearance of "press enter to get started" indicates tha...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-1 chapter 5 boot rom and host software loading traditionally, the loading of switch software is accomplished through the serial port. This approach is slow, inconvenient, and cannot be used for remo...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-2 note: the loading process of the boot rom software is the same as that of the host software, except that during the boot rom loading process, you should press ctrl+u> and enter> after entering the...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-3 input the correct boot rom password (by default, no password is set on the switch). The system enters the boot menu: boot menu 1. Download application file to flash 2. Select application file to b...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-4 2. Set ftp protocol parameter 3. Set xmodem protocol parameter 0. Return to boot menu enter your choice(0-3): step 2: enter 3 in the above menu to load the boot rom software using xmodem. The syst...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-5 figure 5-1 properties dialog box figure 5-2 console port configuration dialog box step 5: click the disconnect> button to disconnect the hyperterminal from the switch and then click the call>butto...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-6 figure 5-3 call and disconnect buttons note: the new bits per second takes effect only after you disconnect and reconnect the terminal emulation program. Step 6: press enter> to start downloading ...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-7 figure 5-5 sending file page after the download completes, the system displays the following information: loading ...Cccccccccc done! Note: you do not need to reset the hyperterminal’s bits per se...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-8 the subsequent steps are the same as those for loading the boot rom software, except that the system gives the prompt for host software loading instead of boot rom loading. 5.2.3 loading software ...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-9 2. Set ftp protocol parameter 3. Set xmodem protocol parameter 0. Return to boot menu enter your choice(0-3): step 4: enter 1 to download the boot rom software using tftp. Then set the following t...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-10 ii. Loading boot rom software pc ftp client ftp server switch console port ethernet port figure 5-7 local loading using ftp step 1: as shown in figure 5-7, connect the switch through an ethernet ...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-11 step 6: enter y to start file downloading or n to return to the bootrom update menu. If you enter y, the system begins to download and update the program. Upon completion, the system displays the...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-12 220 wftpd 2.0 service (by texas imperial software) ready for new user user(none):abc 331 give me your password, please password: 230 logged in successfully [ftp] get s3100-si.Bin [ftp] get s3100-...
Installation manual h3c s3100 series ethernet switches chapter 5 boot rom and host software loading 5-13 5.3.2 remote loading using tftp the remote loading by using tftp is similar to the remote loading by using ftp. The only difference is that it is tftp that you use when loading software to the sw...
Installation manual h3c s3100 series ethernet switches chapter 6 maintenance and troubleshooting 6-1 chapter 6 maintenance and troubleshooting 6.1 software loading failure if software loading fails, the system keeps running in original version. In this case, check if the physical ports are properly ...
Installation manual h3c s3100 series ethernet switches chapter 6 maintenance and troubleshooting 6-2 7. Skip current configuration file 8. Set bootrom password recovery 9. Set switch startup mode 0. Reboot enter your choice(0-9): select 7> and restart the switch. After that, the system will skip the...
Installation manual h3c s3100 series ethernet switches chapter 6 maintenance and troubleshooting 6-3 z data bits: 8 z parity: none z stop bits: 1 z flow control: none z emulation: vt100..
Installation manual h3c s3100 series ethernet switches table of contents i table of contents appendix a lightning protection of the switch.........................................................................A-1 a.1 installation of lightning arrester for ac power (socket strip with lightning prot...
Installation manual h3c s3100 series ethernet switches appendix a lightning protection of the switch a-1 appendix a lightning protection of the switch a.1 installation of lightning arrester for ac power (socket strip with lightning protection) caution: lightning arrester will not be shipped with the...
Installation manual h3c s3100 series ethernet switches appendix a lightning protection of the switch a-2 caution: z make sure that the arrester is well grounded before using the lightning arrester for power. Z after inserting ac power cord plug of switch into the socket of lightning arrester, if the...
Installation manual h3c s3100 series ethernet switches appendix a lightning protection of the switch a-3 z multimeter z tilted wire cutter ii. Installation procedure step 1: tear the protection paper at one side of the double faced adhesive tape apart from the tape, and stick the tape on the surface...
Installation manual h3c s3100 series ethernet switches appendix a lightning protection of the switch a-4 iii. Installation precautions fully consider the following items in the installation process, otherwise, the performance of the lightning arrester for network port will be affected: z lightning a...