H3c s5500-si complete series ethernet switches installation manual hangzhou h3c technologies co., ltd. Http://www.H3c.Com manual version: 20070910-c-1.00
Copyright © 2007, hangzhou h3c technologies co., ltd. And its licensors all rights reserved no part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of hangzhou h3c technologies co., ltd. Trademarks h3c, , aolynk, , h 3 care, , top g, , irf, n...
About this manual related documentation in addition to this manual, each h3c s5500-si complete series ethernet switches documentation set includes the following: manual description h3c s5500-si series ethernet switches operation manual it is used for assisting the users in data configurations and ty...
Conventions the manual uses the following conventions: i. Gui conventions convention description button names are inside angle brackets. For example, click . [ ] window names, menu items, data table and field names are inside square brackets. For example, pop up the [new user] window. / multi-level ...
Installation manual h3c s5500-si complete series ethernet switches table of contents i table of contents chapter 1 product overview ........................................................................................................ 1-1 1.1 preface...................................................
Installation manual h3c s5500-si complete series ethernet switches table of contents ii 3.4 connecting console cable .............................................................................................. 3-17 3.4.1 console cable...................................................................
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-1 chapter 1 product overview 1.1 preface h3c s5500-si series ethernet switches (hereinafter referred to as s5500-si series) are gigabit ethernet switching products developed by h3c. Currently, s5500-si se...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-2 model combo port corresponding port 49 46 50 48 51 45 s5500-52c-si s5500-52c-pwr-si 52 47 note: a gigabit combo port and its corresponding 10/100/1000base-t autosensing ethernet port cannot be used toge...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-3 1.2 introduction to s5500-si series ethernet switches 1.2.1 s5500-28c-si ethernet switch i. Front panel the s5500-28c-si ethernet switch provides 24 × 10/100/1000base-t ethernet ports, four gigabit sfp ...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-4 iii. Power supply system the s5500-28c-si ethernet switch supports both ac input and rps 12 v input. The ac input and dc input can be used together to serve as backup for each other. In addition, either...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-5 note: for details about leds on the front panel, refer to section 1.3.1 “leds of s5500-28c-si/s5500-52c-si switch”. Ii. Rear panel (1) (2) (3) (4) (5) (1) (2) (3) (4) (5) (1): ac power input (2): dc pow...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-6 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1): 10/100/1000 base-t autosensing et...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-7 input voltage range: 90 vac to 264 vac, 50 hz or 60 hz the s5500-28c-pwr-si ethernet switch supports only the external poe power supply recommended by h3c as the dc power. –48 vdc power cannot be used d...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-8 ii. Rear panel (1) (2) (3) (4) (5) (1) (2) (3) (4) (5) (1): dc power input (2): ac power input (3): grounding screw (4): extended slot 1 (5): extended slot 2 figure 1-8 rear panel of the s5500-52c-pwr-s...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-9 (1) (10) (2) (3) (4) (5) (6) (7) (9) (8) (1): 1000/100 mbps sfp port led (2): 10/100/1000 base-t autosensing ethernet port led (3): console port (4): 7-segment digitron display (5): system led (6): led ...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-10 1.3 introduction to front panel leds 1.3.1 leds of s5500-28c-si/s5500-52c-si switch the s5500-28c-si/s5500-52c-si ethernet switch provides leds on the front panel for your convenience to monitor the sw...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-11 led mark status description post running green, blinking the post id of the in-process test is displayed. Post failed red, blinking the post id of the failed test blinks. Loading software green, blinki...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-12 led mark status description green the port works at the rate of 1000 mbps; the led blinks quickly when the port is sending or receiving data. Yellow the port works at the rate of 10/100 mbps; the led b...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-13 table 1-4 description on the leds of the s5500-28c-pwr-si/s5500-52c-pwr-si ethernet switch led mark status description rate mode green, on the port status leds are showing the port rate. Duplex mode ye...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-14 led mark status description post running green, blinking the post id of the in-process test is displayed. Post failed red, blinking the post id of the failed test blinks. Loading software green, blinki...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-15 led mark status description green the port works at the rate of 1000 mbps; the led blinks quickly when the port is sending or receiving data. Yellow the port works at the rate of 10/100 mbps; the led b...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-16 led mark status description green the port works at the rate of 1000 mbps; the led blinks quickly when the port is sending or receiving data. Yellow, blinking (3 hz) post fails on the port. 1000base sf...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-17 led mark status description solid green a power module is installed in the power module slot and the output is normal. Solid yellow a power module is installed in the power module slot but there is an ...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-18 led mark status description green a 1000 mbps link is present. When data is being received or sent, the led flashes at a high frequency. Yellow a 10/100 mbps link is present. When data is being receive...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-19 1.4 system specifications of the s5500-si series table 1-6 system specifications of the s5500-si series item s5500-28c- si s5500-52c -si s5500-28c-pwr -si s5500-52c-pw r-si physical dimensions (h × w ×...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-20 item s5500-28c- si s5500-52c -si s5500-28c-pwr -si s5500-52c-pw r-si operating temperature 0°c to 45°c (32°f to 113°f) relative humidity (noncondens ing) 10% to 90% table 1-7 system specifications of t...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-21 1.5 sfp modules the s5500-28c-si, s5500-52c-si, s5500-28c-pwr-si, and s5500-52c-pwr-si all provide four 1000base-x sfp ports to connect pluggable modules, while the , s5500-20tp-si provides twelve 1000...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-22 1.6.1 one-port 10 ge xfp interface module figure 1-11 front panel of one-port 10 ge xfp interface module this module provides one 10 gbps xfp optical interface. You can select the following xfp optical...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-23 1.6.3 short-haul dual-port 10 ge cx4 interface module figure 1-13 short-haul dual-port 10 ge cx4 interface module this module provides two 10 gbps electrical ports and supports cx4 electrical and proto...
Installation manual h3c s5500-si complete series ethernet switches chapter 1 product overview 1-24 figure 1-14 cx4 cable the following three types of cables are available: z 50 cm (19.7 in.): the connectors at both ends of the cable are bayonet connectors. Z 100 cm (39.4 in.): the connectors at both...
Installation manual h3c s5500-si complete series ethernet switches chapter 2 preparing for installation 2-1 chapter 2 preparing for installation 2.1 safety precautions to avoid any device impairment and bodily injury caused by improper use, observe these rules: z before cleaning the switch, unplug t...
Installation manual h3c s5500-si complete series ethernet switches chapter 2 preparing for installation 2-2 aging of insulation materials and can thus significantly lower reliability and service life of your switch. For the temperature and humidity requirements of different models, refer to section ...
Installation manual h3c s5500-si complete series ethernet switches chapter 2 preparing for installation 2-3 z as the ac power system is a tn system, use a single-phase three-wire power socket with protection earth (pe) to effectively filter interference from the power grid. Z keep the device far fro...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-1 chapter 3 installing the switch caution: when you ask your sales agent to maintain the switch, you must ensure that the dismantlement-preventive seal on a mounting screw of the h3c switch chassis i...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-2 note: z when the depth of a switch is greater than 300 mm (11.8 in), the front mounting ears only secure the switch rather than bear its weight. Z guide rails purchased from h3c apply only to stand...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-3 when you install s5500-si series ethernet switches into 19-inch standard cabinets, you should select front and rear mounting ears with a proper length according to the physical dimensions of switch...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-4 note: guide rails are optional parts. Check table 3-1 to see whether you need to order them or not. Iii. Use front mounting ears to install a switch follow these steps to mount a switch into a 19-i...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-5 front panel front mounting ear front square-holed bracket front mounting ear front panel front mounting ear front square-holed bracket front mounting ear figure 3-5 fix front mounting ears (2) iv. ...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-6 front panel screw 1 front mounting ear three installation locations for screw 1 (select one according to the actual requirement) front mounting ear screw 1 front panel screw 1 front mounting ear th...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-7 5) hold the bottom of the switch with one hand and the front part of the switch with the other hand, and push the switch into the cabinet gently, as shown in figure 3-8. Front square-holed bracket ...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-8 6) fix the other end of the front mounting ears to the front brackets with screws and captive nuts and ensure that front and rear mounting ears have fixed the switch in the cabinet securely, as sho...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-9 figure 3-11 install guide rails 4) hold the two sides of the switch and slide it gently along the guide rails into the cabinet until it is located in a proper position, as shown in figure 3-12. Ens...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-10 rear panel guide rail figure 3-13 effect diagram of front mounting ear and guide rail installation note: ensure a clearance of 1u (44.45 mm, namely, 1.75 inches) between devices for the purpose of...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-11 3.2 connecting the power cords and the ground wire 3.2.1 connecting the ac power cord i. Ac power source socket (recommended) you are recommended to use a single-phase three-wire power socket with...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-12 note: the ac power cord retainer can prevent the ac power cord from accidentally falling off. Step 4: check whether the pwr led on the front panel of the switch is on. If the led is on, it shows t...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-13 (2) (1) (1): air filter (2): fastening screw figure 3-17 12v-rps power socket for the ethernet switch z connect one connector (in a direction) of the 12v-rps dc power cable (figure 3-18 shows a re...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-14 + - null + - null +: working ground -: -52 vdc to -55 vdc null: reserved figure 3-19 appearance of the rps dc power socket of the switch 1) connect one end of the grounding wire (delivered with th...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-15 caution: z make sure that the ground wire has been properly connected before powering on the switch. Z the length of the dc power cord must be less than 3 m (9.8 ft). 3.2.3 connecting the ground w...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-16 than 0.5 m (1.64 ft) into the earth. Weld the yellow-green ground wire of the switch onto the angle iron/steel pipe, and treat the joint for corrosion protection. ( 1 ) ( 5 ) ( 1 ) ( 2 ) ( 3 ) ( 4...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-17 (2) (3) (6) ( 8 ) ( 9 ) (1) ( 8 ) ( 8 ) ( 9 ) ( 9 ) (11) (7) (4) ( 8 ) ( 9 ) (1) ( 8 ) ( ) ( 9 ) ( ) (11) (10) (5) (2) (3) (6) ( 8 ) ( 9 ) (1) ( 8 ) ( 8 ) ( 9 ) ( 9 ) (11) (7) (4) ( 8 ) ( 9 ) (1) ...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-18 figure 3-25 console cable table 3-3 console cable pinouts rj-45 signal direction db-9 (modem) db-9 (console) 1 rts → 7 8 2 dtr → 4 6 3 txd → 3 2 4 cd ← 1 5 5 gnd — 5 5 6 rxd ← 2 3 7 dsr ← 6 4 8 ct...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-19 note: when connecting a pc to a powered-on switch, you are recommended to connect the db-9 connector of the console cable to the pc before connecting the rj-45 connector to the switch. When discon...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-20 ii. Appearance and front panel of a dual-port 10 ge xfp interface module figure 3-28 appearance of a dual-port 10 ge xfp interface module figure 3-29 front panel of a dual-port 10 ge xfp interface...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-21 (1): switch (2): optional module slot (3): xfp interface module (4): push-in direction figure 3-30 install a 10 ge xfp interface module step 4: tighten the fastening screws with a screwdriver to f...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-22 caution: when installing or removing an optional interface module, pay attention to the following points: z do not use too much force in the operation, and do not touch the surface-mounted compone...
Installation manual h3c s5500-si complete series ethernet switches chapter 3 installing the switch 3-23 3.6 installing dedicated cx4 cable 3.6.1 installing dedicated cx4 cable note: make sure that you have installed a cx4 interface module before installing dedicated cx4 cables. Step 1: put on an esd...
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-1 chapter 4 powering on the switch for the first time 4.1 setting up the configuration environment set up the configuration environment as shown below: z connect a terminal (a pc ...
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-2 parameter requirements: set “bits per second” to 9,600, “data bits” to 8, “parity” to “none”, “stop bits” to 1 and “flow control” to “none”. Select vt100 as terminal emulation. ...
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-3 figure 4-3 set the serial port used by the hyperterminal connection 3) click after selecting a serial port and the system pops up the following interface. On the interface, set ...
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-4 4) click after setting the serial port parameters and the system enters the following interface. Figure 4-5 hyperterminal window choose [properties] in the hyperterminal dialog ...
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-5 4.4 booting the switch 4.4.1 checking before powering on the switch before powering on the switch, verify that: z the power cord and ground wire are properly connected. Z the po...
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-6 note: z the system has two startup modes: normal startup and fast startup. The normal startup mode takes a little longer time than the fast startup mode because of more self-tes...
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-7 field description enter your choice(0-9): enter your choice from 0 to 9 z if you perform no operation or press a key other than within two seconds, once the remaining waiting ti...
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-8 the current mode is fast startup mode! Are you sure to change it to full startup mode? Yes or no(y/n) enter y. The system displays the following information: setting startup mod...
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-9 than within five seconds, the system begins to automatically start up and the following information is displayed: auto-booting... Decompress image..................................
Installation manual h3c s5500-si complete series ethernet switches chapter 4 powering on the switch for the first time 4-10 note: the h3c series switches provide abundant command views. For detailed descriptions about the configuration commands and cli, refer to h3c s5500-si series ethernet switches...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-1 chapter 5 boot rom and host software loading traditionally, the loading of switch software is accomplished through the serial port. This approach is slow, inconvenient, and cannot be u...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-2 note: the loading process of the boot rom software is the same as that of the host software, except that during the boot rom loading process, you must enter the different digit after e...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-3 boot menu 1. Download application file to flash 2. Select application file to boot 3. Display all files in flash 4. Delete file from flash 5. Modify bootrom password 6. Enter bootrom u...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-4 step 2: enter 3 in the above menu to load the boot rom and host software using xmodem protocol. The system displays the following download baud rate setting menu: please select your do...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-5 figure 5-1 properties dialog box figure 5-2 console port configuration dialog box step 5: after setting the baud rate, you need to disconnect and the reconnect hyperterminal so that th...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-6 to disconnect the hyperterminal from the switch and then click the button to reconnect the hyperterminal to the switch. Figure 5-3 connect and disconnect buttons note: the new baud rat...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-7 figure 5-5 page for file sending step 9: after the download completes, the system displays the following information: loading ...Cccccccccc done! Note: you do not need to reset the hyp...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-8 the subsequent steps are the same as those for loading the boot rom software, except that the system gives the prompt for host software loading instead of boot rom loading. 5.2.3 loadi...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-9 2. Set ftp protocol parameter 3. Set xmodem protocol parameter 0. Return to boot menu enter your choice(0-3): step 4: select 1 in the boot rom update menu to download the boot rom soft...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-10 you can use ftp to load software onto the switch through an ethernet port. In this case, the switch can act as an ftp server or an ftp client. In the following example, the switch act...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-11 step 5: press after inputting the information above. The system displays the following information: are you sure to update your bootrom?Yes or no(y/n) step 6: enter y to start file do...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-12 ftp 10.1.1.1 trying ... Press ctrl+k to abort connected. 220 wftpd 2.0 service (by texas imperial software) ready for new user user(none):s5500 331 give me your password, please passw...
Installation manual h3c s5500-si complete series ethernet switches chapter 5 boot rom and host software loading 5-13 5.3.2 remote loading using tftp the remote loading by using tftp is similar to the remote loading by using ftp. The only difference is that it is tftp that you use when loading softwa...
Installation manual h3c s5500-si complete series ethernet switches chapter 6 maintenance and troubleshooting 6-1 chapter 6 maintenance and troubleshooting 6.1 software loading failure if software loading fails, the system keeps running in original version. In this case, check if the physical ports a...
Installation manual h3c s5500-si complete series ethernet switches chapter 6 maintenance and troubleshooting 6-2 select 7, and then restart the switch. After the switch is restarted, the user password is removed. 6.2.2 missing boot rom password please contact with your switch dealer. 6.3 power suppl...
Installation manual h3c s5500-si complete series ethernet switches table of contents i table of contents appendix a lightning protection of the switch.........................................................................A-1 a.1 installation of lightning arrester for ac power (socket strip with li...
Installation manual h3c s5500-si complete series ethernet switches appendix a lightning protection of the switch a-1 appendix a lightning protection of the switch a.1 installation of lightning arrester for ac power (socket strip with lightning protection) caution: lightning arrester will not be ship...
Installation manual h3c s5500-si complete series ethernet switches appendix a lightning protection of the switch a-2 caution: z make sure that the arrester is well grounded before using the lightning arrester for power. Z after inserting ac power cord plug of switch into the socket of lightning arre...
Installation manual h3c s5500-si complete series ethernet switches appendix a lightning protection of the switch a-3 z multimeter z tilted wire cutter ii. Installation procedure step 1: tear the protection paper at one side of the double faced adhesive tape apart from the tape, and stick the tape on...
Installation manual h3c s5500-si complete series ethernet switches appendix a lightning protection of the switch a-4 iii. Installation precautions fully consider the following items in the installation process, otherwise, the performance of the lightning arrester for network port will be affected: z...