1. DL manuals
  2. H3C
  3. Network Router
  4. MSR Series
  5. User Manual

H3C MSR Series User Manual

Other manuals for MSR Series: Command Reference Manual
Manual is about: Comware 7 Security

Summary of MSR Series

  • Page 1

    H3c msr series routers oap/oaps v2 module user guide hangzhou h3c technologies co., ltd. Http://www.H3c.Com document version: 6pw102-20120703.

  • Page 2

    Copyright © 2011-2012, hangzhou h3c technologies co., ltd. And its licensors all rights reserved no part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of hangzhou h3c technologies co., ltd. Trademarks h3c, , aolynk, , h 3 care, , top g, , i...

  • Page 3

    Preface the h3c msr series routers oap/oaps v2 module user guide describes hardware specifications of oap/oaps v2 modules, configuration on routers, and how to log in to the operating system of an oap/oaps v2 module. This preface includes: • audience • conventions • about the h3c msr documentation s...

  • Page 5

    Obtaining documentation you can access the most up-to-date h3c product documentation on the world wide web at http://www.H3c.Com . Click the links on the top navigation bar to obtain different categories of product documentation: [technical support & documents > technical documents] – provides hardw...

  • Page 6

    I contents overview ··········································································································· 1 panel views ······································································································· 2 oap smart mim module ·······························...

  • Page 7

    1 overview the open application platform (oap) and open application platform-smart (oaps) are designed for new services. H3c msr series routers provides the following oaps and oap modules: • oap smart mim module • oap mim module • oap fic module an oaps or oap module can be installed in the expansio...

  • Page 8

    2 panel views oap smart mim module figure 1 front panel (1) usb port (2) 100/1000base-t ethernet port led (3) link led for the gigabitethernet management port (4) stand by button (5) system status led (sys) (6) disk led (disk) (7) gigabitethernet management port oap mim module figure 2 front panel (...

  • Page 9

    3 oap fic module figure 3 front panel (1) 100/1000base-t ethernet port led (2) link led for the gigabitethernet management port (3) stand by button (4) system status led (sys) (5) disk led (6) gigabitethernet management port (7) usb port leds table 2 led description led mark status description sys s...

  • Page 10

    4 led mark status description disk steady green the disk is in position. Flashing green the disk is performing a read/write operation. Steady yellow a problem has occurred to the disk. Off the disk is not in position. Link/act steady yellow a link is present on the port. Flashing yellow data is bein...

  • Page 11

    5 gigabitethernet management port table 4 gigabitethernet management port specifications item specification oap oaps connector type rj-45 port type mdi/mdix auto-sensing port transmission rate • 10/100 mbps, half/full duplex • 1000 mbps, half duplex frame format ethernet_ii ethernet_snap.

  • Page 12

    6 configuring acfp and acsei on the router note: after installing the oap/oaps module on the router, perform the following configurations on the router. Acfp configuration introduction to acfp application control forwarding protocol (acfp) is a collaboration framework for the client/server model bet...

  • Page 13

    7 enabling acfp server follow these steps to enable the acfp server: to do… use the command… remarks enter system view system-view — enable the acfp server acfp server enable required disabled by default configuring the acfp client you must configure the acfp collaboration policy and acfp collaborat...

  • Page 14

    8 • acsei client is integrated into the software system of the oap module. It is a function supported by the oap module. Enabling acsei server follow these steps to enable acsei server: to do… use the command… remarks enter system view system-view — enable acsei server acsei server enable required d...

  • Page 15

    9 logging in to and resetting the linux operating system of an oap/oaps module you can perform the following operation and configuration to the oap/oaps module on the router: • redirecting to an oap/oaps module from the router • reset the linux system of the oap/oaps module redirecting to an oap/oap...

  • Page 16

    10 to do… use the command… remarks reset the linux system of an oap/oaps module oap reboot slot slotnum required available in user view note: resetting the oap/oaps module may cause data loss and service interruption. Before resetting the oap/oaps module, save the configurations of the module operat...