- DL manuals
- H3C
- Switch
- S3100-SI Series
- Quick Start Manual
H3C S3100-SI Series Quick Start Manual
Summary of S3100-SI Series
Page 1
H3c s3100-si series ethernet switches quick start hangzhou h3c technologies co., ltd. Http://www.H3c.Com manual version: t2-08225g-20070415-c-1.05.
Page 2: Ltd. and Its Licensors
Copyright © 2006-2007, hangzhou h3c technologies co., ltd. And its licensors all rights reserved no part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of hangzhou h3c technologies co., ltd. Trademarks h3c, , aolynk, , h 3 care, , top g, , i...
Page 3: About This Manual
About this manual related documentation in addition to this manual, each h3c s3100-si series ethernet switches documentation set includes the following: manual content h3c s3100-si series ethernet switches operation manual it is used for assisting the users in data configurations and typical applica...
Page 4: Conventions
Chapter contents 2 installation preparation introduces the installation preparation and precaution of s3100-si series ethernet switches. 3 installation introduces the procedures to install an s3100-si series ethernet switch, including the setup of the mainframe, cards and cables. 4 lightning protect...
Page 5: Environmental Protection
Symbols ii. Convention description warning means reader be extremely careful. Improper operation may cause bodily injury. Caution means reader be careful. Improper operation may cause data loss or damage to equipment. Note means a complementary description. Environmental protection this product has ...
Page 6: Table of Contents
Quick start h3c s3100-si series ethernet switches table of contents i table of contents chapter 1 product overview ........................................................1-1 1.1 s3100-26t-si ethernet switch ..........................................1-1 1.1.1 appearance ................................
Page 7
Quick start h3c s3100-si series ethernet switches table of contents ii 1.5 s3100-16c-si/s3100-16c-si-dc ethernet switch..........1-10 1.5.1 appearance ...........................................................1-10 1.5.2 front panel ............................................................1-10 1....
Page 8
Quick start h3c s3100-si series ethernet switches table of contents iii chapter 3 installation ....................................................................3-1 3.1 installation of the switch ....................................................3-1 3.1.1 mounting the switch into a 19-inch cabin...
Page 9: Chapter 1 Product Overview
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-1 chapter 1 product overview 1.1 s3100-26t-si ethernet switch 1.1.1 appearance as shown in the following figure, the s3100-26t-si ethernet switch provides 24 x 10/100base-tx ethernet ports, two 10/100/1000base-t ethernet ...
Page 10: 1.1.3 Rear Panel
Quick start er 1 product overvie h3c s3100-si series ethernet switches chapt w 1-2 (1) power led (2) a/l mode led (3) d/s mode led (4) port left led (yellow) (5) port right led (green) (6) 10/100 base-tx port (7) 10/100/1000 base-t port (8) console port (9) link led (green) (10) active led (yellow) ...
Page 11: 1.1.4 Power System
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-3 1.1.4 power system the s3100-26t-si ethernet switch supports ac input power module. Z rated voltage range: 100 vac to 240 vac, 50/60 hz z max voltage range: 90 vac to 264 vac, 47 hz to 63 hz 1.1.5 cooling system the s31...
Page 12: 1.2.3 Rear Panel
Quick start er 1 product overvie h3c s3100-si series ethernet switches chapt w 1-4 (1) power led (2) a/l mode led (3) d/s mode led (4) port left led (yellow) (5) port right led (green) (6) 10/100 base-tx port (7) 10/100/1000 base-t port (8) console port (9) link led (green) (10) active led (yellow) ...
Page 13: 1.2.4 Power System
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-5 1.2.4 power system the s3100-16t-si ethernet switch supports ac input power module. Z rated voltage range: 100 vac to 240 vac, 50/60 hz z max voltage range: 90 vac to 264 vac, 47 hz to 63 hz 1.2.5 cooling system the s31...
Page 14: 1.3.3 Rear Panel
Quick start er 1 product overvie h3c s3100-si series ethernet switches chapt w 1-6 (1) power led (2) a/l mode led (3) d/s mode led (4) port left led (yellow) (5) port right led (green) (6) 10/100 base-tx port (7) 10/100/1000 base-t port (8) console port (9) link led (green) (10) active led (yellow) ...
Page 15: 1.3.4 Power System
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-7 1.3.4 power system the s3100-8t-si ethernet switch supports ac input power module. Z rated voltage range: 100 vac to 240 vac, 50/60 hz z max voltage range: 90 vac to 264 vac, 47 hz to 63 hz 1.3.5 cooling system the s310...
Page 16: 1.4.3 Rear Panel
Quick start chapter 1 product overvie h3c s3100-si series ethernet switches w 1-8 (1) power led (2) a/l mode led (3) d/s mode led (4) port left led (yellow) (5) port right led (green) (6) 10/100 base-tx port (7) expansion slot (8) console port (9) mode switch button figure 1-11 front panel of the s3...
Page 17: 1.4.4 Power System
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-9 i. Rear panel of the s3100-26c-si model supporting ac input: (1) ac power socket (2) grounding screw figure 1-12 rear panel of the s3100-26c-si model supporting ac input ii. Rear panel of the s3100-26c-si model supporti...
Page 18: 1.4.5 Cooling System
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-10 z max voltage range: –36 vdc to –72 vdc 1.4.5 cooling system the s3100-si series cool off in nature way. 1.5 s3100-16c-si/s3100-16c-si-dc ethernet switch 1.5.1 appearance as shown in the following figure, the s3100-16c...
Page 19: 1.5.3 Rear Panel
Quick start er 1 product overvie h3c s3100-si series ethernet switches chapt w 1-11 (1) power led (2) a/l mode led (3) d/s mode led (4) port left led (yellow) (5) port right led (green) (6) 10/100 base-tx port (7) expansion slot (8) console port (9) mode switch button figure 1-15 front panel of the ...
Page 20: 1.5.4 Power System
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-12 i. Rear panel of the s3100-16c-si model supporting ac input: (1) ac power socket (2) grounding screw figure 1-16 rear panel of the s3100-16c-si model supporting ac input ii. Rear panel of the s3100-16c-si model support...
Page 21: 1.5.5 Cooling System
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-13 1.5.5 cooling system the s3100-si series cool off in nature way. 1.6 s3100-8c-si/s3100-8c-si-dc ethernet switch 1.6.1 appearance as shown in the following figure, the s3100-8c-si/s3100-8c-si -dc ethernet switch provide...
Page 22: 1.6.3 Rear Panel
Quick start er 1 product overvie h3c s3100-si series ethernet switches chapt w 1-14 (1) power led (2) a/l mode led (3) d/s mode led (4) port left led (yellow) (5) port right led (green) (6) 10/100 base-tx port (7) expansion slot (8) console port (9) mode switch button figure 1-19 front panel of the ...
Page 23: 1.6.4 Power System
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-15 i. Rear panel of the s3100-8c-si model supporting ac input: (1) ac power socket (2) grounding screw figure 1-20 rear panel of the s3100-8c-si model supporting ac input ii. Rear panel of the s3100-8c-si model supporting...
Page 24: 1.6.5 Cooling System
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-16 1.6.5 cooling system the s3100-si series cool off in nature way. 1.7 s3100-si series front panel leds 1.7.1 power led table 1-1 description of the power led on s3100-si series led mark on the panel status description o...
Page 25: 1.7.3 Mode Button
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-17 table 1-2 description of the port status leds on the s3100-si series mode led status port status leds and their status description flashing data is passing through the port. Yellow led (left) off no data is passing thr...
Page 26
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-18 after the switch is powered on, the a/l led lights up initially. If you press the mode button, the d/s led lights up. After that, if you press the mode button again within 45 seconds, the a/l led lights up again, or el...
Page 27
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-19 item s3100-26t- si s3100-16t-si s3100-8t-si number of fixed ports 24 x 10/100base- tx auto-sensing ports 2 x 10/100/1000 base-t ports 16 x 10/100base-t x auto-sensing ports 1 x 10/100/1000b ase-t port 8 x 10/100base- t...
Page 28
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-20 1.8.2 s3100-26c-si/s3100-16c-si/s3100-8c-si ethernet switch technical specifications table 1-4 s3100-26c-si/s3100-16c-si/s3100-8c-si ethernet switch technical specifications item s3100-26c-si s3100-16c-si s3100-8c-si p...
Page 29
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-21 item s3100-26c-si s3100-16c-si s3100-8c-si supported expansion interface module type 10/100/1000base-t interface module with max transmission distance of 100 m (328.1 feet) 100base-sx (sc, 2 km (1.2 mi)) 100base-lx (sc...
Page 30
Quick start h3c s3100-si series ethernet switches chapter 1 product overview 1-22 item s3100-26c-si s3100-16c-si s3100-8c-si poe (as powered device) not supported supported supported system power consumption (full load) 20 w 12 w 10 w fan none none none operating temperature 0°c to 45°c relative hum...
Page 31: 2.1 Precautions
Quick start h3c s3100-si series ethernet switches chapter 2 installation preparation 2-1 chapter 2 installation preparation 2.1 precautions to avoid any device impairment and bodily injury because of improper use, please take the following precautions: z before cleaning the switch, pull out the powe...
Page 32
Quick start h3c s3100-si series ethernet switches chapter 2 installation preparation 2-2 2.2 requirements on environment s3100-si series must be used indoors. When you install your switch in a cabinet or install it directly on a workbench, you must ensure: z enough space is left near the air-intake ...
Page 33
Quick start h3c s3100-si series ethernet switches chapter 2 installation preparation 2-3 damage to the switch. High temperature for a long time will speed up the aging of insulation material, greatly lower the reliability of the switch and greatly reduce the life span of the switch. 2.2.2 cleanness ...
Page 34
Quick start h3c s3100-si series ethernet switches chapter 2 installation preparation 2-4 table 2-2 limits on harmful gas in the equipment room gas max content (mg/m³) so 2 0.2 h 2 s 0.006 nh 3 0.05 cl 2 0.01 2.2.3 anti-interference requirements a switch in use may be affected by the interference fro...
Page 35: 2.2.4 Laser Usage Security
Quick start h3c s3100-si series ethernet switches chapter 2 installation preparation 2-5 2.2.4 laser usage security s3100-si series are category-1 laser equipment. When an optional optical interface card of the s3100-si series is operating, it is prohibited to stare into the optical interface becaus...
Page 36: Chapter 3 Installation
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-1 chapter 3 installation caution: on a mounting screw of the chassis of any h3c series switches, there is a seal which must be kept intact before the agent maintains the switch for you. You must get the permission of your loc...
Page 37
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-2 step 2: place the switch on a shelf of the cabinet, and slide the switch into the cabinet along the guides in the cabinet to an appropriate position. Step 3: insert screws through the mount ears into the front mounting post...
Page 38: 3.1.3 Wall-Mount
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-3 3.1.2 mounting the switch on a workbench when a 19-inch standard cabinet is not available, you can simply place the switch on a clean workbench. When doing so, you should ensure: z the workbench is stable and well grounded....
Page 39
Quick start er 3 installation h3c s3100-si series ethernet switches chapt 3-4 figure 3-3 anchor kit illustration the wall-mount procedure is as follows (see figure 3-4): 1) drill two holes in the wall on the same horizontal line, with a distance of 169 mm. 2) insert anchor kits into the holes. 3) dr...
Page 40
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-5 caution: when mounting the switch, keep the ethernet ports of the switch facing downwards and the two sides with ventilation holes vertical to the ground. 3.2 installation of expand card note: the following section describe...
Page 41: Wire
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-6 ii. Installation of an onu subcard step 1: dismount the dummy panel of an expansion slot of the switch. Step 2: insert the onu card into the expansion slot to the place. Step 3: fix the onu card firmly with captive screws. ...
Page 42
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-7 ii. Connecting ac power cord step 1: connect one end of the chassis grounding wire (coming with the switch) to the grounding screw on the rear of the chassis and the other end to the ground nearby. Step 2: connect one end o...
Page 43
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-8 step 1: connect one end of the chassis grounding wire (coming with the switch) to the grounding screw on the rear of the chassis and the other end to the ground nearby. Step 2: connect the dc power terminals of the switch t...
Page 44
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-9 3.3.3 connecting grounding wire caution: you should properly connect the switch grounding wire since it is crucial to the lightning protection and electromagnetic shield (ems) of your switch. The power input end of the swit...
Page 45
Quick start chapter 3 installation h3c s3100-si series ethernet switches 3-10 ( 1 ) ( 4 ) ( 1 ) ( 4 ) ( 3 ) ( 1 ) ( 4 ) ( 1 ) ( 4 ) ( 3 ) ( 2 ) ( 1 ) ( 4 ) ( 1 ) ( 4 ) ( 3 ) ( 1 ) ( 4 ) ( 1 ) ( 4 ) ( 3 ) ( 2 ) (1) power input (2) grounding screw (3) grounding wire (4) grounding strip figure 3-8 grou...
Page 46
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-11 y figure 3-9 grounding the switch by burying the grounding bod into the earth z for an ac-powered switch, if none of the above two conditions is available, ground it through the pe wire of the ac power supply. In this case...
Page 47
Quick start er 3 installation h3c s3100-si series ethernet switches chapt 3-12 (1 ) (2 ) (4 ) (3 ) (6 ) (5 ) (8 ) ( 7) (11 ) (1 0 ) (1 ) (2 ) (4 ) (3 ) (6 ) (5 ) (8 ) (8 ) ( 7) (11 ) (9 ) (1 ) (2 ) (4 ) (3 ) (6 ) (5 ) (8 ) ( 7) (11 ) (1 0 ) (1 ) (2 ) (4 ) (3 ) (6 ) (5 ) (8 ) (8 ) ( 7) (11 ) (9 ) (1)...
Page 48
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-13 3.4 connecting optical fiber caution: z after a switch starts, the pon interface may emit invisible radial when there is no optical connector connected to it and the protective cap is removed from it. Therefore, do not sta...
Page 49: 3.5.1 Console Cable
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-14 step 3: plug the optical connector into the pon interface of the onu subcard. 3.5 connection of console cable 3.5.1 console cable console cable is an 8-core shielded cable. At one end of the cable is a crimped rj45 connect...
Page 50
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-15 rj-45 signal direction db-9 7 dsr → 6 8 cts → 8 3.5.2 connecting console cable follow these steps to connect a terminal device, a pc for example, to the switch: step 1: connect the db-9 female connector of the console cabl...
Page 51
Quick start h3c s3100-si series ethernet switches chapter 3 installation 3-16 note: when connecting a pc to a powered-on switch, you are recommended to connect the db-9 connector of the console cable to the pc before connecting the rj45 connector to the switch. When disconnecting a pc from a powered...
Page 52: Switch
Quick start h3c s3100-si series ethernet switches chapter 4 lightning protection of the switch 4-1 chapter 4 lightning protection of the switch 4.1 installation of lightning arrester for ac power (socket strip with lightning protection) caution: lightning arrester will not be shipped with the switch...
Page 53
Quick start chapter 4 lightning protection of the switch h3c s3100-si series ethernet switches 4-2 mainboard grounding and polarity indicator (red) : on means that the lines are wrongly connected (either the ground wire is not well connected, or the live and zero lines are wrongly connected). Please...
Page 54
Quick start h3c s3100-si series ethernet switches chapter 4 lightning protection of the switch 4-3 caution: z make sure that the arrester is well grounded before using the lightning arrester for power. Z after inserting ac power cord plug of switch into the socket of lightning arrester, if the green...
Page 55: Network Port
Quick start h3c s3100-si series ethernet switches chapter 4 lightning protection of the switch 4-4 4.2 installation of lightning arrester for network port note: lightning arrester for network port is specially designed for the ethernet port of 10/100m electrical interface (rj-45 connector is adopted...
Page 56
Quick start h3c s3100-si series ethernet switches chapter 4 lightning protection of the switch 4-5 ii. Installation procedure step 1: tear the protection paper at one side of the double faced adhesive tape apart from the tape, and stick the tape on the surface of the arrester. Tear the protection pa...
Page 57
Quick start chapter 4 lightning protection of the switch h3c s3100-si series ethernet switches 4-6 switch network cable indoors power input network cable led i lightning arrester f (attached onto th ground wire of light grounding screw metal cabinet th nto from outdoor or network port e chassis) nin...
Page 58
Quick start h3c s3100-si series ethernet switches chapter 4 lightning protection of the switch 4-7 htning arresters for all these network ports for protection. Interconnect with other devices via cables outdoor, you should install lig.