H3c wa2200 series wlan access points installation manual hangzhou h3c technologies co., ltd. Manual version: 6pw104-20091228.
Copyright © 2008-2009, hangzhou h3c technologies co., ltd. And its licensors h3c technologies co., ltd., a subsidiary of 3com corporation. All rights reserved no part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of hangzhou h3c technologie...
About this manual organization the h3c wa2200 series wlan access points installation manual is organized as follows: chapter contents 1 product overview introduces the hardware configuration, appearances, and interfaces of the wa2200 series. 2 installation preparations introduces the environment req...
In addition to this manual, each h3c wa series wlan access points(fit) documentation set includes the following: manual description h3c wx series access controllers user manual provides a guide to the operation of h3c series access controller products (including access controllers, access controller...
Available to manage your installation with minimal disruption to your network. Expert assessment and implementation services are offered to fill resource gaps and ensure the success of your networking projects. More information on 3com maintenance and professional services is available at http://www...
I table of contents 1 product overview ······································································································································1-1 introduction ··············································································································...
1-1 the models listed in this manual are not applicable to all regions. Please consult the local agents for the models applicable to your region. 1 product overview introduction the h3c wa2200 series wlan access points (hereinafter referred to as the wa2200 series) are developed by hangzhou h3c tech...
1-2 figure 1-2 appearance of the wa2200 series table 1-1 physical dimensions of the wa2200 series model physical dimensions (h×w×d) weight wa2210-ag/wa2220-ag, (indoor) 40×166×118 mm (1.57×6.54×4.65 in.) 0.5 kg (1.10 lb) wa2210x-g/wa2220x-ag, (outdoor) 76×245×245 mm (2.99×9.65×9.65 in.) 2 kg (4.41 l...
1-3 the wa2200 series have extraordinary radio frequency (rf) performance and provide consummate service functions. With ip66 degree of protection, the outdoor models can be directly deployed outdoors to simplify the installation. The models of the wa2200 series are designed for application in vario...
1-4 the wa2210-ag is a single-rf device. The 11a and 11b/g leds cannot be on or flash at the same time. Wa2210x-g/wa2220x-ag figure 1-4 leds on the wa2210x-g figure 1-5 leds on the wa2220x-ag table 1-4 description of leds on the wa2210x-g/wa2220x-ag led color qty meaning power green 1 displays the p...
1-5 led color qty meaning 100base-fx yellow 1 displays the status of the optical interface: z on: the link on the optical interface is up. Z off: the link on the optical interface is down. Z flashing: data is being transmitted or received. 11a green 1 displays the wireless link status: z off: the wi...
1-6 table 1-5 descriptions of interfaces on wa2200 series wlan access points model interface standards and protocols description antenna interface 1 ieee802.11b/g wa2210-ag: main antenna interface, 2.4/5-ghz wa2220-ag: 2.4-ghz antenna interface console interface rs/eia-232 the console interface is u...
1-7 interfaces provided by wa2210-ag/wa2220-ag figure 1-6 interfaces on wa2210-ag/wa2220-ag top view bottom view antenna interface 1 antenna interface 2 z wa2210-ag is a single-rf device. Viewed from the front, the antenna interface on the left (antenna interface 1 in figure 1-6) is the main antenna...
1-8 interfaces provided by wa2210x-g/wa2220x-ag figure 1-7 interfaces on wa2210x-g/wa2220x-ag right view（wa2220x-ag） bottom view（wa2210x-g/wa2220x-ag） consol interface grounding screw antenna interface1 10/100base-tx 100base-fx antenna interface2 wa2210x-g is a single-rf device and provides no 5-ghz...
2-1 2 installation preparations this chapter describes the preparations for wa2200 installation, including preparation of installation tools, environment examination, and unpacking & inspection. Safety precautions installation and removal of the unit and its accessories must be carried out by qualif...
2-2 table 2-1 is only for reference. If you install the ap on a desk, none of the above tools is required; if you install the ap on top of or under eave of a building, no digging tool is required. Examining the installation site before installation, you should examine the installation site to keep t...
2-3 table 2-3 power supply power source connection details ordering information ac/dc power adapter h3c wa2200 series access points can accept power from an ac/dc power adapter. Input specification is as follows: +48v , 0.52a min. Connect the adapter’s power jack to the ap power interface. If you ne...
2-4 sn item requirements 4 power grounding (ac) z use a power cord with a protective earth (pe). Do not use a power cord with only an l line and an n line. Z the neutral line of the power cord should not be connected with the pgnd of other communications equipment. The l and n lines cannot be connec...
3-1 3 installation of indoor aps you can directly place an indoor model (including the enhanced model) on a desk. The rubber feet on the bottom of the ap help you to place it horizontally. Or you can fix it onto a wall by using the wall-mounting bracket. The following introduces the wall-mounting pr...
3-2 installing the ap the following describes how to install the ap on a wall. Z installing the wall-mounting bracket on a wall z installing the ap on the wall-mounting bracket z locking the ap onto the wall-mounting bracket (optional) installing the wall-mounting bracket on a wall follow these step...
3-3 figure 3-3 install the wall-mounting bracket when installing the wall-mounting bracket, position it so that the arrowhead points upward. Installing the ap on the wall-mounting bracket follow these steps to install the ap on the wall-mounting bracket: step1 align the ap with the hooks on the wall...
3-4 figure 3-4 fix the indoor ap onto the wall-mounting bracket expansion screw hock (1) (2) locking the ap onto the wall-mounting bracket (optional) the indoor aps have a security slot on the top, which can be used to lock the ap onto the wall-mounting bracket to prevent theft. Follow these steps t...
3-5 figure 3-5 lock the indoor ap onto the wall-mounting bracket the lock is user supplied. Connecting the power supply local power supply connect the ap to the power adapter and then to the power source, as shown in figure 3-6..
3-6 figure 3-6 local power supply connection power interface power adapter power over ethernet if the uplink device of the ap is a poe switch or the like, use an ethernet cable to directly connect the ethernet interface of the ap to the poe device. Figure 3-7 poe connection z in the case of poe, you...
3-7 figure 3-8 connect the ap to the network internet wa2200 wired station wireless station wired station switch.
4-1 4 installation of outdoor aps the outdoor models of the wa2200 series are h3c wa2210x-g and h3c wa2220x-ag. You can select an appropriate model according to the actual requirement. The two outdoor models are waterproof, dustproof, and lightningproof. Installation flowchart you can install your o...
4-2 figure 4-2 installation flowchart of the ap on a wall start mark drill holes install anchors end fix the wall-mounting bracket fix the ap 1) mark step operation 1 put the wall-mounting bracket on the installation position against the wall. 2 mark three expansion screw holes on the wall. For the ...
4-3 figure 4-3 wall-mounting bracket structure and positions of screw holes 195.0 135.0 80.0 40.0 70.0 220.0 2) drill holes step operation 1 use a percussion drill with a 6-mm (0.24-in) bit to drill holes on the three markings. Observe the following precautions when drilling: z hold the drill handle...
4-4 step operation 1 put an anchor into each hole vertically. 2 tap the flat end of the anchor with a rubber hammer until the anchor is flush with the wall surface. 4) fix the wall-mounting bracket step operation 1 align the three holes in the wall-mounting bracket with the anchors and insert three ...
4-5 with an outer diameter of 60 to 110 mm (2.36 to 4.33 in) through the fixing support. The mounting plate and the v-shaped bracket are fixed through the self-clinching bolt and a nut, as shown in figure 4-5. Figure 4-5 mounting plate and v-shaped bracket you can adjust the angle of the ap as neede...
4-6 figure 4-7 pole and pole base step4 fix the mounting plate onto one v-shaped fixing bracket with a self-clinching bolt. Step5 fix the pair of v-shaped fixing brackets on a vertical or horizontal pole with tie-bar bolts, flat washers, spring washers, and nuts (see figure 4-8 or figure 4-9). Figur...
4-7 figure 4-9 install the outdoor ap on a horizontal pole step6 fix the ap onto the mounting plate with screws (see the dashed line and arrow in figure 4-8 or figure 4-9). You can first install the fixing support onto the pole and then the ap onto the mounting plate, or vice versa. Installing an ou...
4-8 follow these steps to install a pole on a parapet: step1 weld the lightning rod onto the tip of the pole. Step2 install the pole on a parapet or cement pier. Step3 use a 40 × 4 mm (1.57 × 0.16 in) flat steel to connect the pole to the ground grid step4 use pole-mounting brackets to install the d...
4-9 z if there are parapets around the building top and the parapet height is less than 1200 mm (47.24 in), fix one point of the pole to the parapet with one expansion bolt and the other point to the building top surface with another expansion bolt, and fix the directional outdoor antenna onto the p...
4-10 figure 4-13 install an omni antenna under a special environment lightning rod omni outdoor antenna clamp antenna ploe > 1000mm 45° angle steel in figure 4-13, the antenna pole is welded with two angle steels to the lightning rod pole, instead of a cement pier. Installing an omni antenna on the ...
4-11 figure 4-14 install an omni antenna on the ap directly z after the omni antenna is installed on the ap, the antenna should be at least one meter away from the pole or other metal objects. Z the outdoor ap and the feeder lightning arrester are each equipped with a 3-meter-long grounding cable. I...
4-12 step2 connect one end of the rf cable to the feeder lightning arrester and the other end to the outdoor antenna. Step3 wrap each joint with insulation tape first, and then with waterproof tape. Z it is recommended to install a feeder lightning arrester on each antenna interface and ground it we...
4-13 figure 4-16 connect the ethernet optical interface to the uplink device figure 4-17 exploded view of the port lightning protector (poe) z if the uplink device is a poe switch, no port lightning protector or power adapter is required. It is not recommended to provide power to the ap using a poe ...
4-14 since an ethernet cable needs to pass through a waterproof cover for waterproof purpose (an ethernet cable with an rj-45 connector is unable to pass through), you need to prepare an ethernet cable connector on site. Usually a category-5 or enhanced category-5 twisted pair cable is adopted. Figu...
4-15 pin of rj-45 connector signal category-5 twisted pair cable signal direction pin of rj-45 connector 3 rx+ white (green) Å 1 4 — blue — 4 5 — white (blue) — 5 6 rx- green Å 2 7 — white (brown) — 7 8 — brown — 8 z when distinguishing or preparing these two types of ethernet cables, you can refer ...
4-16 connecting an optical fiber be sure to follow the instructions below when connecting a fiber cable. Otherwise, the ap may get damaged. When connecting the ap to the remote device through a fiber cable, use an appropriate sfp module. The sfp modules provided by h3c can be used outdoor. These sfp...
4-17 the fiber cable is a 10-meter tail fiber with a waterproof cover. One end of the fiber is an lc connector with a waterproof joint, and the other end is an sc connector, which can be connected to a fiber or device. For users using an optical cable terminal box, you can insert the sc connector of...
4-18 z if a poe switch is used to supply power, no port lightning protector or power adapter is required. It is not recommended to provide power to the ap using a poe switch over a long distance. Z to supply power to the ap through a port lightning protector, you need to connect the port lightning p...
4-19 figure 4-22 connection of external cables of the ap outdoor antenna rf cable fiber cable grounding cable outdoor antenna ethernet cable grounding cable for feeder lightning arrester connecting the network in practice, the ap can be connected to the internet or a man through an ethernet interfac...
4-20 figure 4-23 connection between the ap and internet (the ap works in the fat ap mode) a special outdoor waterproof ethernet cable is required to connect the ap and waterproof treatment should be made to the ethernet cable at the outlet of the chassis..
