Hacker Pitts EPP ARF orange Construction Manual

Summary of Pitts EPP ARF orange

  • Page 1

    Mega force 400+ technická data/ technical data g 850 mm 760 mm 390 g 4 superaerobatic model for “3d” aerobatic flying superakrobatický model pro létání “3d” www.Hacker-model.Com rychlostavebnice rychlostavebnice almost ready to fly almost ready to fly www.Hacker-model.Com pitts epp èervený / ed pitt...

  • Page 2

    Stavební návod www.Hacker-model.Com www.Hacker-model.Com construction guide pitts special 3 model is produced by modern technology on cnc machines from epp “almost unbreakable” material. + 6 85 0 4 channel rc set with 3 micro servos, extension servo cables 100mm 1x and 150mm 2x, power set mega force...

  • Page 3

    Www.Hacker-model.Com rc set- 4 channel and power set rc sestava 4 kanálová s pohonnou jednotkou elektromotor electromotor pohonná baterie accu pack regulátor otáèek speed controller pøijímaè 4 kanálový receiver 4 channel serva servos køidélka ailerons výškovka elevator smìrovka rudder vypínaè switch...

  • Page 4

    1 1 trup / fuselage hc 1299a(b,c)090 2 1 levé dolní køídlo / left lower wing hc 1299a(b,c)080 2a 1 levé horní køídlo / left upper wing hc1299a(b,c)085 3 1 pravé dolní køídlo / right lower wing spolu s 2 / along with 2 3a 1 pravé horní køídlo / right upper wing spolu s 2a / along with 2a 4 1 vop / ho...

  • Page 5

    6 1 ca 1 6 20 40 www.Hacker-model.Com www.Hacker-model.Com 5 12 vložte do trupu lože podvozku podle obrázku a zalepte ho po celém obvodu calepidlem. Insert the landing gear mount into fuselage . Glue the landing gear mount into fuselage around the edge. Use caglue. 1 12 12 1 12 1 ca 1 12 1 2 pøiložt...

  • Page 6

    Ca 2 1 do spodního køídla ( + ) zasuòte vzpìry . Insert the wing strut into the lower wing ( + ) as shown. 2 3 28 28 2 3 28 28 1 27 ! Do trupu zasuòte baldachýn . Dodržte polohu dvou otvorù podle obrázku. Insert the baldachin into the fuselage as shown. Keep right position of two holes at back side ...

  • Page 7

    4 15 10mm osa konektoru axis connector záøezy slots modeláøským nožem as shown. Vyøíznìte do køidélek záøezy pro páky køidélek podle obrázku. Cut a slots in the ailerons for the control horns 21 21 7 10 17 osa konektoru táhla pro smìrovku axis of pushrod connector for rudder 16 16 10 1 ca 1 32 18 1 ...

  • Page 8

    2 3 7 ca 1 29 25mm 4 5 ca 5 1 4 9 8 www.Hacker-model.Com www.Hacker-model.Com 24 1 táhlo výškovky odstøíhnìte cca 10mm od konektoru táhla . Cut the pushrod as shown. 16 cca 10mm smìrovku pøilepte na trup ca lepidlem. Kontrolujte kolmost a souosost smìrovky podle nákresu. Glue vertical fin on the fus...