Instruction manual m-16 chisel morticer (240v) 125mm timber width capacity w347 page 1 instructions manual for m-16 (w347) 07/06/2017.
Chisel mortiser model m -16 assembl y and opera tiong instr u ction / p a rt s list page 2 instructions manual for m-16 (w347) 07/06/2017.
M -16 chisel mortiser v.02 01-11-2010 １ general safety rules woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain hazards involved with the operation of the product. Using the machine with respect and caution will considerabl...
M -16 chisel mortiser v.02 01-11-2010 ２ 16. Use recommended accessories. The use of accessories and attachments not recommended by manufacturer may cause hazards or risk of injury to persons. 17. Reduce the risk of unintentional starting. Make sure switch is in “off” position before plugging in powe...
M -16 chisel mortiser v.02 01-11-2010 ３ additional safety rules for chisel mortisers 1. Do not operate this machine until it is assembled and installed according to the instructions. 2. Obtain advice from your supervisor, instructor, or another qualified person if you are not familiar with the opera...
M -16 chisel mortiser v.02 01-11-2010 ４ warning: failure to follow these rules may result in serious personal injury. Save these instructions. Refer to them often and use them to instruct others. Connecting tool to power source power connections a separate electrical circuit should be used for your ...
M -16 chisel mortiser v.02 01-11-2010 ５ use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord, which has a grounding type plug and a receptacle, which will accept the tool’s plug. When using an extension cord, be sure to use one heavy enough to...
M -16 chisel mortiser v.02 01-11-2010 ６ assembly warning: for your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. Raising and lowering handle 1. Assemble hub of handle assembly (a) fig. 2...
M -16 chisel mortiser v.02 01-11-2010 ７ fig 4 fence the fence (a) fig. 5, can be moved in or out by loosening lever (b), sliding fence to the desired position and tightening lever (b). Fig5 fig6 depth stop a depth stop guide (a) fig. 6, is provided to limit the depth of the chisel (b). To adjust the...
M -16 chisel mortiser v.02 01-11-2010 ８ installing chisel & bit 1. Loosen lock screw, shown in figure 7. Fig 7 fig 8 2. Insert chisel bushing (with the hole facing forward) into the head. Tighten the screw just enough to hold the chisel in place. ! Note: set the slot in the side of the chisel to the...
M -16 chisel mortiser v.02 01-11-2010 ９ fig 9 fig 10 3. Use a small, triangular, smooth file to relieve the inner corners of the chisel. See fig.10. Remove any burrs from the outside of the chisel with a fine oilstone. Wiring diagram page 11 instructions manual for m-16 (w347) 07/06/2017.
M -16 chisel mortiser v.02 01-11-2010 １０ parts diagram for m -16 page 12 instructions manual for m-16 (w347) 07/06/2017.
M -16 chisel mortiser v.02 01-11-2010 １１ part list for m -16 page 13 instructions manual for m-16 (w347) 07/06/2017.
M -16 chisel mortiser v.02 01-11-2010 １２ please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate recycling bin. Only for eu countries do not dispose ...
