Hague Quality Water Hydroclean HC3 Owner's Manual And Installation Manual - Filter Descriptions
HC3 Owner’s Manual
12/11/2013
41
Water Conditioner Specifications
Five-Button Dual Mode Controller
HC3 25
HC3 25CX
HC3 35
HC3 48
HC3 64
HC3 105
Max Compensated Hardness–gpg (g/L)
60 (1.0)
25 (0.4)
90 (1.5)
110 (1.9)
120 (2.0)
130 (2.2)
Iron in solution–ppm
2
1
NA
6
1
8
1
10
1
10
1
Minimum pH–standard units
7
7
7
7
7
7
Tannin–ppm
NA
NA
NA
NA
NA
NA
Sulfur–ppm–SulfurStat
NA
NA
NA
NA
NA
NA
Maximum Chlorine–ppm
1
1
1
1
1
1
Capacity grains (grams) @ 2.5 lb (1.1 kg) salt/cu.ft.
2
(# 1 Salt Setting)
10,700 (693) 10,700 (693) 14,700 (951) 20,100 (1300) 26,800 (1735) 44,300 (2870)
Capacity grains (grams) @ 3.8 lb (1.7 kg) salt/cu.ft.
(# 2 Salt Setting)
14,700 (951) 14,700 (951) 20,200 (1310) 27,500 (1780) 36,700 (2375) 60,600 (3920)
Capacity grains (grams) @ 5.0 lb (2.3 kg) salt/cu.ft.
(# 3 Salt Setting)
17,800 (1150) 17,800 (1150) 24,500 (1590) 33,500 (2170) 44,600 (2890) 73,700 (4770)
Capacity grains (grams) @ 7.0 lb (3.2 kg) salt/cu.ft.
(# 4 Salt Setting)
22,200 (1440) 22,200 (1440) 30,500 (1970) 41,600 (2690) 55,400 (3590) 91,500 (5920)
Capacity grains (grams) @ 15 lb (6.8 kg) salt/cu.ft.
(# 5 Salt Setting)
25,600 (1660) 25,600 (1660) 35,200 (2280) 48,000 (3110) 64,000 (4140) 105,000 (6800)
Brine line flow control refill–gpm (L/min)
0.5 (1.9)
0.5 (1.9)
0.5 (1.9)
0.5 (1.9)
0.5 (1.9)
0.5 (1.9)
Media tank size–inches (cm) Dia. x Ht.
8 x 44
(20 x 112)
9 x 48
(23 x 122)
9 x 48
(23 x 122)
10 x 54
(25 x 137)
12 x 52
(30 x 132)
14 x 65
(36 x 165)
Resin/media amount cu.ft. (cu. m)
0.8 (0.02)
1.1 (0.03)
1.1 (0.03)
1.5 (0.04)
2.0 (0.06)
3.3 (0.09)
Media type
HCR
HCR/HCM
HCR
HCR
HCR
HCR
Bed depth–inch (cm)
30 (76)
33 (84)
33 (84)
35 (89)
34 (86)
43 (109)
Freeboard–inch (cm)
14 (36)
15 (38)
15 (38)
19 (48)
18 (46)
22 (56)
Water Pressure–min–max psi (bar)
20–120
(1.4–8.3)
20–120
(1.4–8.3)
20–120
(1.4–8.3)
20–120
(1.4–8.3)
30–120
(2.1–8.3)
30–120
(2.1–8.3)
Water temperature–min–max °F (°C)
40–120 (4–49) 40–120 (4–49) 40–120 (4–49) 40–120 (4–49) 40–120 (4–49) 40–120 (4–49)
Minimum water volume for backwash–gpm (L/min)
1.5 (5.6)
2.0 (7.5)
2.0 (7.5)
2.4 (9.1)
4.0 (15)
5.0 (19)
Flow Rate gpm (L/min)( @ 15 psi drop
9 (34)
10.5 (40)
10 (38)
12 (45)
16 (60)
18.5 (70)
Pressure Drop in psi (bar) @ normal flow rate–gpm
(L/min)
7.8@6
(0.54@22.7)
7.2@6
(0.50@22.7)
7.6@6
(0.52@22.7)
7.3@9
(0.50@34.1)
8.5@12
(0.59@45.4)
11@14
(0.76@53.0)
Pipe size–inch
3/4
3/4
3/4
3/4
1
1
Height–inch (cm)
48 (122)
52 (132)
52 (132)
58 (147)
56 (142)
69 (175)
Floor space–inch (cm)
18 x 27
(46 x 69)
18 x 28
(46 x 71)
18 x 28
(46 x 71)
18 x 29
(46 x 74)
26 x 36
(66 x 91)
30 x 38
(76 x 97)
Brine or solution tank size–inch (cm)
18 x 33
(46 x 84)
18 x 33
(46 x 84)
18 x 33
(46 x 84)
18 x 33
(46 x 84)
24 x 50
(61 x 127)
24 x 50
(61 x 127)
Brine or solution tank capacity–lb (kg)
200 (91)
200 (91)
200 (91)
200 (91)
640 (290)
640 (290)
Water volume per regen. gal–factory setting (L)
From 19.5
(73.7)
From 24.5
(92.6)
From 27.5
(104)
From 35
(132)
From 51.5
(195)
From 69
(260)
Length of regeneration (minutes)
From 23
From 23
From 27
From 32
From 21
From 28
Shipping weight–lb (kg)
100 (45)
125 (57)
130 (59)
160 (73)
190 (86)
275 (125)
Quartz Gravel–lb (kg)
10 (4.5)
12 (5.4)
12 (5.4)
14 (6.4)
20 (9.1)
30 (13.6)
Standard Features:
Metered or timed HC3 valve, Hydro-Clean
distributor, high capacity resin and self-leveling
thermo media tank.
Options: Low profile valve cover, 1-inch full flow
bypass valve.
Legend:
1
When iron is present in the raw water supply, regeneration frequency cannot exceed 96
hours. Additionally, a minimum salt setting of 7 lb (3.2 kg) per cubic foot of resin is required.
2
Do not use standard 18-inch (45.7 cm) diameter brine tank with salt grid for salt settings
less than 3 lb (1.4 kg).
N/A: No Application
Filter Descriptions
The following table describes the available filters.
Filter
Purpose
HC3 2IF
Removes iron and iron algae. Also removes up to 5 ppm H
2
S with the presence of 2 ppm iron. Refer to HC3 2IF Sizing
Formula to determine regeneration frequency.
HC3 1CF
Removes tastes, odors and will reduce most man-made pollutants. Backwashes as needed.
HC3 1NF
Designed to raise the pH of most low-pH water. The mineral media must be replenished periodically. Backwashes
every 2 days.
HC3 1MMF
Designed to remove heavy sediment and suspended solids. It is capable of filtering down to 10 microns in size.
Backwashes as needed.