Document number: 45i00-1 45a00-1 installation instructions description the model 45a00-1 supervised wireless receiver allows up to 64 unique wireless security transmitters to report information to an hai controller. The wireless transmitters replace wired door and window sensors, as well as wired sm...
1 installation install the receiver in a central area of the premises, as high above ground as practical. The receiver may be mounted up to 1000 feet from the hai controller. ¾ the receiver should be at least 5 feet from the controller or any other electronic device. ¾ avoid areas where receiver wil...
2 mode set +12v a b gnd d3 type led led display mode led mode/advance switch set switch antenna specifications dimensions: 2.5w x 3.75h x 1.0d, excluding antenna current consumption: 30ma maximum operating temperature: 32 o f - 140 o f (0 o c - 60 o c) maximum humidity: 90% relative humidity, non-co...
3 operation the two operating modes of the receiver are "run" and "setup". In run mode, with the receiver connected to and communicating with the controller, the mode led (see figure 2) should blink once per second. The receiver monitors the status of each transmitter. If the status condition of a t...
4 type led - in setup mode,the type led (see figure 2) is used to indicate if a transmitter is supervised. Setup mode the setup mode is used to configure the general operating parameters of the receiver, to program a transmitter into the receiver, and to change the characteristics of a programmed tr...
5 if no transmitter is programmed in an address location, neither the mode led nor the type led will be lit. If a transmitter is programmed in an address location: 1. The mode led indicates whether the transmitter sends restore transmissions ¾ the mode led is on if the transmitter sends restore tran...
6 transmitter setup 1. Press and hold the mode/advance button for two (2) seconds. 2. "a1" will appear. On omnilt, omni ii, and lumina "a1" is always used. On omnipro ii and lumina pro the address will depend on the number of expansion enclosures used (see "omnipro ii / lumina pro setup" for more in...
7 reset memory to erase all transmitters from memory and to reset to the factory default configuration, press and hold both the set and mode/advance switches simultaneously for 2 seconds. The display will show "ee". If you choose to continue, press and hold the set and mode/advance switches simultan...
8 co ntr ol le r bl a c k g r een ye l lo w re d gn d +12v a b d3 mo d e s e t wireless rec e ive r gree n yello w blac k red.
9 omnilt setup a. At a console, select "installer setup" (press 9, installer code, then #). Press 2 for “zones”, and then press 1 # (“wireless receiver?” yes = 1). B. When connected to omnilt, zones 9-24 are the wireless receiver zones. C. When connected to omnilt, the receiver address on the 45a00-...
10 1. Connect the "a" & "b" terminals of the 45a00-1 to the "a" & "b" terminals under the section marked "console" on the controller. 2. Connect the "+12" and "gnd" terminals of the 45a00-1 to the "12v" and "gnd" terminals under the section marked “console” on the controller. Verify that the status ...
11 green yello w blac k red mod e d3 wi re le s s re ce iv er +1 2v se t gn d ab co ntr oll er bl a c k gre e n ye llo w red.
12 omnipro ii and lumina pro setup a. Omnipro ii and lumina pro can have two 45a00-1 wireless receivers connected. When connected, the 45a00-1 is recognized as an expansion enclosure. Each 45a00-1 can handle up to 64 wireless zones, in groups of 16. Each group of 16 zones is considered 1 expansion e...
13 note: if two 45a00-1 wireless receivers are connected, the first 45a00-1 must be addressed between 1-4 (a1-a4), and the second must be addressed between 5-8 (a5-a8). The charts below describe where each group of wireless transmitters (groups of 16) on the 45a00-1 wireless receiver relates to each...
14 hai controller indications when the condition of a transmitter changes state, the hai console will display that condition as follows: transmitter condition hai console display when a transmitter (zone) is violated zone name "not rdy" when a cover is removed from a transmitter zone name "not rdy" ...
To enter setup mode, press and hold the mode/advance switch for 2 seconds. Display description set switch mode/advance switch a 1 enter the receiver address changes the current address (1-8) advances to the next item n 1 enter number of addresses changes number of addresses (1-4) advances to the nex...
