- DL manuals
- HAI
- Thermostat
- RC-122B
- Owner's Manual
HAI RC-122B Owner's Manual
Summary of RC-122B
Page 1
O m n i s t a t electronic communicating thermostat owner's manual rc-122b / rc-122bz two stage heat/cool 2 stage heat / 2 stage cool with energy efficient control document number 13r00-17 may, 2007 : day p cool auto.
Page 2
Copyright © 1999-2007 home automation, inc. All rights reserved.
Page 3
Contents introduction ............................................................................................. 1 description.................................................................................................. 1 maintenance..............................................................
Page 4
This thermostat is listed by underwriter's laboratories and ul canada. This thermostat has been tested and found to comply with the requirements of the european union for electromagnetic interference, electromagnetic immunity and safety under the applicable emi and low voltage directives and standar...
Page 5
1 introduction thank you for purchasing your new rc-122 two stage electronic communicating thermostat. Your thermostat will provide you with comfort, convenience, and energy savings for years to come. We hope that you take a few moments to become familiar with all of the features of this fine produc...
Page 6
2 about two stage units... Two stage systems have two "speeds" of heating and cooling. "stage 1" is similar to "low speed" and "stage 2" is similar to "high speed". In most cases, stage 1 is sufficient to heat or cool the building, but from time to time, due to hot or cold weather, stage 2 is needed...
Page 7
3 operation to take advantage of all the benefits and features offered by your thermostat, we recommend that you start by becoming familiar with its operation. Note : to check your desired setting without changing it, press the up or down arrow key ( ∧ or ∨) once. 1- display the display is used to s...
Page 8
4 3- prog press the prog (programming) key to set the current time and day (hours, minutes, day of week), and to program the temperature time schedules for the morn, day, eve, and nite periods. 4- mode press the mode key to set the thermostat mode to off, heat, cool, or auto . In off mode, the heati...
Page 9
5 display the following icons will be displayed during normal operation: 1- temperature display shows the current temperature, desired temperature, or heating and cooling settings. 2- time display shows the current time of day. 3- desired desired is displayed when the temperature display shows the d...
Page 10
6 5- the top is displayed when stage 1 of the heating or cooling system is running. The bottom is displayed when stage 2 of the heating or cooling system is running. 6- cool cool is displayed when the system is in cool mode. 7- auto auto is displayed when in automatic changeover mode. 8- heat heat i...
Page 11
7 filter reminder your thermostat logs the amount of time your heating and cooling system has been running and gives you a reminder when it's time to replace your filter. " f i l t " will be displayed every four seconds in the place of the time display when it is time to change you filter. To clear ...
Page 12
8 setting the current time and day to set or change the current time and day, press and release the prog key. The hour will blink. 1. Use the arrow keys ( ∧ − ∨ ) to change the hour . 2. Press the prog key to advance to minutes. 3. Use the arrow keys ( ∧ − ∨ ) to change minutes. 4. Press the prog ke...
Page 13
9 programming your thermostat may be programmed to adjust the heating and cooling settings up to 4 times per day ( morn, day, eve, and nite). You can setup a temperature time schedule for weekdays, saturday, and sunday. To enter programming mode, press the prog key 4 times. When in programming mode:...
Page 14
10 setting time schedules to view or change the programming time schedules of your thermostat, press and the prog key four times. The weekday morn time will flash. 1. Use the arrow keys ( ∧ − ∨ ) to change the scheduled time for the displayed period ( morn, day, eve, or nite). 2. Press the prog key ...
Page 15
11 repeat steps 1-6 for the day, eve, and nite periods. Afterwards, repeat steps 1-6 for 4 daily periods on saturdays (day 6), and 4 daily periods on sundays (day 7). The temperature display will show "6" for saturdays, and "7" for sunday times. Note: if programming mode is not being used and day/ni...
Page 16
12 automatic time update the thermostat time will automatically be updated by the connected automation system. Power outages the thermostat will restart the heating/cooling system 3 to 8 minutes after the electricity comes back on. All settings and programs are stored permanently, and will not be af...
Page 17
Time schedules the table below shows the time schedules that are currently set into your thermostat. There is a blank table at the bottom that can be used to plan changes to the current schedule. Weekdays saturdays sundays morn 6:00 am 8:00 am 8:00 am cool 78 78 78 heat 70 70 70 day 8:00 am cool 85 ...
Page 20
Two year limited warranty home automation, inc. (hai), warrants this product against defects in material and workmanship, under normal use and service, for a period of two (2) years from the date of purchase by the consumer. During the warranty period, hai will repair or replace, at its option, any ...