1 hi-203e gps receiver hi-203e gps receiver.
General description of what gps is and how it works. Gps (global positioning system) is the only system today able to show you your exact position on the earth anytime, in any weather, anywhere. Gps satellites, 24 in all, orbit at 11,000 nautical miles above the earth. They are continuously monitore...
3 2 ps/2 connector color function cn1 green tx 5 white rx 4 red vcc 2 black gnd 1 1 2 1 3 5 2 4 6 1 2 1800±30mm global positioning system hi-203e gps receiver pin assignment connectors pocket pc hi-203e ps/ii gps receiver can connecting to a female ps/ii connector. One end from the female connector ...
Hi-203e is a gps receiver with ps/ii mini-din interfaces and built-in active antenna for high sensitivity to tracking signal. Hi-203e is well suited to system integration and users who use any kinds of mobile devices, such as, pda, notebook pc, tablet pc, etc. It satisfies a wide variety of applicat...
Section 1 introduction 1.1 overview the hi-203e gps receiver is intended for use in a wide range of applications. The receiver simultaneously tracks up to twelve satellites, provides accurate satellite positioning data with fast time-to-first-fix (ttff) and low power consumption. It is designed for ...
Section 2 receiver operation upon power up, after initial self-test has completed, the hi-203e will begin satellite acquisition and tracking process. Under normal open-sky condition, position-fix can be achieved within approximately 45 seconds (within 15 seconds if valid ephemeris data is already co...
2.1 receiver specifications features general sensitivity update rate accuracy acquisition reacquisition dynamics operation temperature storage temperature operating humidity primary power current consumption serial interface protocol datum antenna nmea message dimension 2.2 led indicator led off led...
Section 3 hardware interface 3.1 mechanical dimensions unit:mm top view lateral view bottom view 41±0.2 20±0.2 41±0.2 8 58±0.2 i/o cable i/o cable i/o cable led indicator cpu.
3.2 rf module hardware interface 9 1 2 3 4 5 6 7 8 9 10 rfic pin 1 2 3 4 5 6 7 8 9 10 description nc nc vcc input : 3.3v ctrl : input signal for rf module power-saving control gnd : power and signal ground ref out : 16.367mhz reference output gnd : power and signal ground if out : 4.092mhz if signal...
3.3 baseband hardware interface the 10 pin-connector is the same as the rf connector. A1 : gnd, ground a2 : 1pps valid signal (1:valid, 0:invalid) a3 : 1pps b1 : tx, serial port output (gps navigation output) b2 : rx, serial port input b3 : vcc, power supply input, 3.8v ~ 8.0v dc unregulated the fol...
3.4 one-pulse-per-second (1pps) output the one-pulse-per-second output is provided for applications requiring precise timing measurements. The output pulse is 1usec in duration. Rising edge of the output pulse is accurate to +/-1usec with respect to the start of each gps second. Accuracy of the one-...
Section 4 software interface this section describes the details of the serial port commands through which the hi-203e is controlled and monitored. The serial port commands allow users to set the receiver parameters, configure output message type, and retrieve status information. The baud rate and pr...
Appendix b default values the product has the following factory preset default values: datum: 000 (wgs-84) nmea enable switch: baud rate: elevation mask: dop mask: receiver operating mode: commands can be issued to the hi-203e to change the settings of the receiver. The new settings will remain effe...
14 troubleshooting problem reasons solutions no position output but timer is counting weak or no gps signal can be received at the place of hi-203e unit connect an external antenna to hi-203e and place the antenna under a open space, then, press 'reset' at outdoor space but gps signal is blocked by ...
14 gps receiver gps receiver offizielle vertretung schweiz: sintrade ag kriesbachstrasse 30 ch-8600 dübendorf www.Sintrade.Ch.
