- DL manuals
- Haicom
- GPS
- HI-203E
- User Manual
Haicom HI-203E User Manual - Hi-203E Gps Receiver
Summary of HI-203E
Page 1
User manual hi-203e mini-din gps receiver hi-203e mini-din gps receiver.
Page 2
1 hi-203e gps receiver hi-203e gps receiver.
Page 3: General Description of What
2 general description of what gps is and how it works. Gps (global positioning system) is the only system today able to show you your exact position on the earth anytime, in any weather, anywhere. Gps satellites, 24 in all, orbit at 11,000 nautical miles above the earth. They are continuously monito...
Page 4
3 although gps was designed for military use, many thousands of civi lians make use of it. The satellites actually broadcast two signals, one is only formilitary use, and the ther can be used by both military and civilians. Since gps is passive (you only need to receive the signal), there are no res...
Page 5: Hi-203E Gps Receiver
4 ps/2 connector color function cn1 green tx 5 white rx 4 red vcc 2 black gnd 1 1 3 5 2 4 6 1 1 2 2 1800±30mm global positioning system hi-203e gps receiver pin assignment connectors mini din: 6 pin male connector wire: 3.6 ± 0.1mm.
Page 6
5 pocket pc hi-203e ps/ii gps receiver can connecting to a female ps/ii connector. One end from the female connector is +12v car charger (charging pda and gps receiver simultaneously) the other end form the female ps/ii connector is the pda connector for connecting your pda. For notebook pc use: hi-...
Page 7
6 1. Hi-203e series introductions hi-203e is a gps receiver with ps/ii mini-din interfaces and built-in active antenna for high sensitivity to tracking signal. Hi-203e is well suited to system integration and users who use any kinds of mobile devices, such as, pda, notebook pc, tablet pc, etc. It sa...
Page 8
7 optional accessories: • ps/ii to pda connector and car charger • ps/ii to db9 adapting cable • ps/ii to usb adapting cable hi-203e-xxxx (pocket pc plug) hi-203e-db9 hi-203e-usb.
Page 9
8 section 1 introduction 1.1 overview 12 channel gps sensor module the hi-203e is an all-in-one gps receiver module specifically designed for handheld device market. It features small size, low power consumption, and ease of use. The hi-203e is optimized for good performance and low cost. Its 12 par...
Page 10
9 1.2 features • 12 parallel channel gps receiver • 4000 simultaneous time-frequency search bins • better than -135dbm sensitivity • • • 5m cep accuracy.
Page 11
10 section 2 receiver operation upon power up, after initial self-test has completed, the hi-203e will begin satellite acquisition and tracking process. Under normal open-sky condition, position-fix can be achieved within approximately 35 seconds (within 10 seconds if valid ephemeris data is already...
Page 12
11 as soon as gps signal is acquired and tracked, the hi-203e will transmit valid navigation infor mation through its ser ial interface. The navigation data contains following infor mation: • receiver position in latitude, longitude, and altitude • receiver velocity • time • dop error-magnification ...
Page 13
12 2.1 technical specifications 2.2 led indicator features receiver type accuracy startup time reacquisition acquisition sensitivity update rate dynamics operational limits serial interface protocol datum interface connector input voltage current consumption dimension weight: operating humidity led ...
Page 14
13 section 3 hardware interface 3.1 mechanical dimensions 58±0.2 i/o cable i/o cable i/o cable led indicator cpu top view lateral view bottom view 41±0.2 20±0.2 41±0.2 unit:mm.
Page 15
14 hi-203e lateral view 3.2 pinout description pin number 1 2 3 4 5 6 signal name serial data out 1 serial data in 1 serial data out 2 serial data in 2 power ground description asynchronous serial output at lvttl level, to output nmea message asynchronous serial input at lvttl level, to input comman...
Page 16
15 3.3 one-pulse-per-second (1pps) output the one-pulse-per-second output is provided for applications requiring precise timing measurements. The output pulse is 1usec in duration. Rising edge of the output pulse is accurate to +/-1usec with respect to the start of each gps second. Accuracy of the o...
Page 17
16 as long as enough satellite signals are received to generate valid position fixes, the 1pps output remains synchronized to the gps second, and the 1pps valid signal remains active. If signal blockage prevents the receiver from generating valid position fix, the 1pps output will drift away from th...
Page 18
17 section 4 software interface this section describes the details of the serial port commands through which the hi-203e is controlled and monitored. The serial port commands allow users to set the receiver parameters, configure output message type, and retrieve status information. The baud rate and...
Page 19
18 4.1.1 nmea messages the serial interface protocol is based on the national marine electronics association's nmea 0183 ascii interface specification. This standard is fully define in "nmea 0183, version 3.01" the standard may be obtained from nmea, www.Nmea.Org 4.1.2 gga - gps fix data time, posit...
Page 20
19 note: the checksum field starts with a '*' and consists of 2 characters representing a hex number. The checksum is the exclusive or of all characters between '$' and '*'. Field 1 2 3 4 5 6 7 8 9 10 11 12 13 example 104549.04 2447.2038 n 12100.4990 e 1 06 01.7 00078.8 0016.3 5c description utc tim...
Page 21
20 4.1.3 gll - latitude and longitude, with time of position fix and status latitude and longitude of current position, time, and status. Format: $gpgll,,,,,,,* example: $gpgll,2447.2073,n,12100.5022,e,104548.04,a, a*65 field 1 2 3 4 5 6 7 8 example 2447.2073 n 12100.5022 e 104548.04 a a 65 descript...
Page 22
21 4.1.4 gsa - gps dop and active satellites gps receiver operating mode, satellites used for navigation, and dop values. Format: $gpgsa,,,,,,,,,,, ,,,,,,* example: $gpgsa,a,3,26,21,,,09,17,,,,,,,10.8,02.1,10.6*07 field 1 2 3 4 5 6 7 example a 3 26,21,,,09, 17,,,,,, 10.8 02.1 10.6 07 description mod...
Page 23
22 4.1.5 gsv - gps satellite in view number of satellites in view, prn number, elevation angle, azimuth angle, and c/no. Only up to four satellite details are transmitted per message. Additional satellite in view information is sent in subsequent gsv messages. Format: $gpgsv,,,,,,,, ... , ,,, * exam...
Page 24
23 4.1.6 rmc - recommanded minimum specific gps/transit data time, date, position, course and speed data. Format: $gprmc,,,,,,,,,,, ,* example: $gprmc,104549.04,a,2447.2038,n,12100.4990,e, 016.0,221.0,250304,003.3,w,a*22 field 1 2 3 4 5 6 7 8 9 10 11 12 13 example 104549.04 a 2447.2038 n 12100.4990 ...
Page 25
24 4.1.7 vtg - course over ground and ground speed velocity is given as course over ground (cog) and speed over ground (sog). Format: gpvtg,,t,,m,,n,,k,* example: $gpvtg,221.0,t,224.3,m,016.0,n,0029.6,k,a*1f field 1 2 3 4 5 6 example 221.0 224.3 016.0 0029.6 a 1f description true course over ground,...
Page 26
25 4.1.8 zda time and date format: $gpzda,,,,,,* example: $gpzda,104548.04,25,03,2004,,*6c binary messages see binary message protocol user's guide for detailed descriptions. Field 1 2 3 4 5 6 7 example 104548.04 25 03 2004 6c description utc time in hhmmss.Ss format, 000000.00 ~ 235959.99 utc time:...
Page 27
26 mechanical characteristics unit: mm 25 6.6 25 8 31 46 3.5 10.5 10.5 2.5 4.3 31 1.2 1.5 1.5 0.9 14.5 2.5 2.5 46 3.
Page 28
27 appendix b default values the product has the following factory preset default values: commands can be issued to the hi-203e to change the settings of the receiver. The new settings will remain effective on next power-on as long as the on-board rechargeable backup battery is not discharged. After...
Page 29: Troubleshooting
28 troubleshooting problem reasons solutions no position output but timer is counting weak or no gps signal can be received at the place of hi-203e unit place the hi-203e under an open space, then, press 'reset' at outdoor space but gps signal is blocked by building or car roof to try again, go to o...
Page 31
Waterproof gps receiver waterproof gps receiver.