Haier 0010554405B Installation Manual

Page of 8

Download

Print this page

Bookmark us

No.0010554405

Installation Manual of Room Air Conditioner

No.

Accessory parts

Remote controller

R-03 dry battery

Mounting plate

Drain hose

Steel nail, cement

Screw

Plastic cap

Drain-elbow

Cover

Cushion

Connecting cable

Number

articles

Accessory parts

Optional parts for piping

Mark

Parts name

more than 5cm

more than 10cm

more than 60cm

more than 15cm

Non-adhesive tape

The marks from to in the figure are the parts numbers.

The distance between the indoor unit and the floor should

be more than 2m.

more than 10cm

Adhesive tape

Saddle(L.S) with screws

Attention must be paid to

the rising up of drain hose

Arrangement of piping directions

Rear left

Rear

right

Left

Below

Right

Connecting electric cable

for indoor and outdoor

Drain hose

Heating insulating material

4X50

4X25

Piping hole cover

Read this manual before installation

1.Driver

2.Hacksaw

3.Hole core drill

4.Spanner(17,19 and 26mm)

5.Torque wrench(17mm,22mm,26mm)

6.Pipe cutter

7.Flaring tool

8.Knife

9.Nipper

12.Reamer

10.Gas leakage detector or

soap-and-water solution

11.Measuring tape

Explain sufficiently the operating means to the user

according to this manual.

Change for

fresh air box

Change for

fresh air

tube(suit)

Outlet joint

Screw

Note:1.Cooling only units don't have Drain-elbow

Outlet joint

2. is only for the models of 18,22.

3.The models ZF don't have fresh function

and accessory parts related with freshing.

Drawing for the installation of indoor and outdoor units

Necessary Tools for Installation

1 2 3 4 5 6 7 Next › »

Summary of 0010554405B

Page 1
No.0010554405 b installation manual of room air conditioner no. Accessory parts remote controller r-03 dry battery mounting plate drain hose steel nail, cement screw plastic cap drain-elbow cover cushion connecting cable 1 1 a b c d e f g 2 3 4 5 6 7 8 9 10 2 1 1 6 4 1 1 4 1 number of articles acces...
Page 2
Fixing of outdoor unit indoor unit selection of installation place power source selection of pipe outdoor unit fix the unit to concrete or block with bolts( 10mm) and nuts firmly and horizontally. When fitting the unit to wall surface, roof or rooftop, fix a supporter surely with nails or wires in c...
Page 3
Indoor unit 1.Fitting of the mounting plate and positioning of the wall hole 2.Making a hole on the wall and fitting the piping hole cover when the mounting plate is first fixed when the mounting plate is fixed side bar and lintel 1.Carry out, based on the neighboring pillars or lintels, a proper le...
Page 4
Indoor unit 4.Connecting the indoor/outdoor electric cable fixing the indoor unit body removing the wiring cover [other direction piping] indoor/outdoor electric cable and drain hose must be bound with refrigerant piping by protecting tape. Cut away, with a nipper, the lid for piping according to th...
Page 5
Indoor unit 2.Another way for the models of 18,22 ,24,as illustrated: way one (right direction): take off the lid for right piping pipe,put the outlet joint into the lid,then put the fresh air tube into the outlet jont. Way two (left direction): take off the lid for leftt piping pipe,put the outlet ...
Page 6
Outdoor unit 1.Installation of outdoor unit 3.Connection 4.Attaching drain-elbow 2.Connection of pipes install according to to bend a pipe, give the roundness as large as possible not to crush the pipe ,and the bending radius should be 30 to 40 mm or longer. Connecting the pipe of gas side first mak...
Page 7
Outdoor unit 6.Purging method: 1.Remove the four screws of fresh air box from the back cover. 2.Use six screws to fix fresh air box onto the designated position on the outdoor unit. 3.Remove two screws of the pipe junction of the fresh air box, then insert the flared departure of the change for fres...
Page 8
1.Cut pipe 3.Insert the flare nut 4.Flare pipe it becomes high midway. The end is immersed in water. It waves. The gap with the ground is too small less than 5cm there is the bad smell from a ditch 2.Remove burs 1.Power source installation 2.Cutting and flaring work of piping 3.On drainage check for...