Haier AB092FCAIA Operation And Installation Manual - Cautions
2
All electrical repairs must be carried out
by qualified electricians. Inadequate repairs
may result in a major source of danger for
the user of the air conditoiner.
Do not damage any parts of the air
conditioner that carry refrigerant by
piercing or perforating the air conditioner's
tubes with sharp or pointed items, crushing
or twisting any tubes, or scraping the
coatings off the surfaces. If the refrigerant
spurts out and gets into eyes, it may result
in serious eye injuries.
Do not obstruct or cover the ventilation
grille of the air conditioner. Do not put
fingers or any other things into the
inlet/outlet and swing louver.
Do not allow children to play with the air
conditioner. In no case should children be
allowed to sit on the outdoor unit.
Specifications
The refrigerating circuit is leak-proof.
1. Applicable ambient temperature range:
The machine is adaptive in following
situation
2. If the supply cord is damaged, it must be
replaced by the manufacturer or its service
agent or a similar qualified person.
3. If the fuse on PC board is broken please
change it with the type of T3.15A /250VAC.
Cautions
Cooling
Heating
Indoor
outdoor
Rated Maximum Minimum
27 32 18
19 23 14
35 43 -5
24 26 --
20 27 15
14.5 -- --
7 21 -15
6 15 --
DB C
WB C
DB C
WB C
Indoor
outdoor DB C
WB C
DB C
WB C
2
2
19
Other Instructions
1.Configuration of power supply
Air conditioner must use special power supply system (above 20A), and qualified electrician makes
wiring and fixing according to wiring regulations specified in national standard.
In socket, exactly distinguish earth wire with neutral wire and it is wrong to connect them together.
A leakage breaker must be installed.
Parameters of power supply: H07RN-F 3G 2.0
mm
2
Connection method is Y-connection .If the power cord is damaged, it must be replaced by
professional people of manufacturer or its maintenance department or similar to avoid dangers.
2.Pipe cutting and expanding
Must remove burrs if cut pipes with pipe cutter.
Expand flare after insert the pipe expander.
Installation check and test run
Require customers to use air conditioner according to the operation manual.
The items checked during test run,please mark in
No gas leakage on the pipe joint ?
How about the thermal insulation of the pipe joint:
Is the electrical wiring between indoor and outdoor unit connected to the terminal block firmly?
Is the wiring of indoor and outdoor unit secured firmly?
Is the drainage hose arranged correct?
Is the earthing wire connected firmly?
Is the power supply voltage conformed to the electrical regulation?
Any noise?
Is the display on the control board (LCD) correct?
Cooling normal?
Does the indoor temperature regulator work normally?
For the power supply
L shall be connected to the live wire.
N shall be connected to the neutral wire.
Shall be connected to the earth wire.
The person who has completed this installation shall be requested to conduct a test operation for check:
Is the temperature adjuster working normally?
Does the location for installation conform to requirements?
Winding up with Protective Plastic Tape
The connection pipes, drain pipe, and the connection wires
shall be wound up with PVC tape.
Notes: The connection pipes shall also be wound up with insulating
material to preserve the temperature. The airing direction shall be
from bottom to top.
Trial Operation
Correct
Incorrect
Deflection
Crack occurs
Broken
Incomplete
Over outward
A
Pipe expander
Liquid pipe
Gas pipe
Diameter of pipe
Dimension A (mm)
1.0~1.2
1.4~2.2
6.35mm (1/4î)
12.7mm (1/2î)
Installation Procedures,Check and Test Run
4. The wiring method should be in line with
the local wiring standard.
5. Use copper wire only. The connecting cable
should be H05RN-F 4G 0.75mm . The power
cable should be H05RN-F 3G 2.5mm .
All the cables shall have got the European
authentication certificate.
6. The waste battery shall be disposed properly.
7. The indoor unit installation height is at least
2.5m.
8. The appliance must be installation that the
plug should be easily accessible after
installation.
9. The power plug should be self-provided and
it should have got the Local authenti-
cation certificate.