Haier AMS09H03-N Operation Manual - page 2
Display board
Signal receiver hole
COOL
display
HEAT
display
HEALTH display
Dry
display
4
2
3
1
6
7
5
8
Parts and Functions
4
2
3
1
6
5
(
If the unit which you purchased
has healthy function,follow it.
TIMER OFF display
TIMER ON display
SLEEP display
If not,please ignore.
)
7
ON/OFF
TEMP
MODE
SET
FAN
TIMER
SWING
CLOCK
SLEEP
LOCK
RESET
5
6
7
8
9
10
19
20
21
22
23
4
1
2
3
11
12
13
14
15
16
A
U
T
O
ON
OFF
AM
PM
o
C
17
18
24
HEALTH
1. Operation mode display
2. SWING display
3. FAN SPEED display
LO
MED
HI
AUTO
5. SLEEP display
6. LOCK display
7. SIGNAL SENDING display
8. TIMER OFF display
9. TIMER ON display
10. CLOCK display
11. TEMP display
12. POWER ON/OFF
Used for unit start and stop.
13. MODE
Used to select AUTO run, COOL,
HEAT DRY and FAN operation
15. HOUR
Used to set clock and timer setting.
16. SWING
Used to set auto fan direction.
17. SLEEP
Used to select sleep mode.
18. LOCK
Used to lock buttons and LCD display.
19. TEMP.
Used to select your desired temp.
20. SET
Used to confirm timer and clock
21. TIMER
Used to select TIMER ON,
TIMER OFF, TIMER ON-OFF
22. CLOCK
Used to set correct time
23. RESET
normal condition.
Used to reset the controller back to
4. HEALTH display
24. HEALTH
Used to operate the healthy function
25.
14. FAN
Used to select fan speed LO, MED,
HI, AUTO
Ambient temp.display
When receiving the remote control signal,
display the set temperature and in the rest
this room temperature is only for reference.
time the room temperature is displayed and
25
POWER/SOFT
POWER/SOFT button
26
POWER/SOFT
display
26.
MODE
SET
FAN
TIMER
SWING
CLOCK
6
5
2
1
4
3
Inlet grille
Inlet
Air Purifying Filter (inside)
Outlet
Horizontal flap
6
4
2
1
5
3
5
2
1
5
3
6
8
Parts and Functions
Actual inlet grille may vary from the one shown in the
manual according to the product purchased
(adjust up and down air flow
Don't adjust it manually)
(adjust left and right air flow)
Vertical blade
Remote controller
If the unit which you purchased has healthy function,follow it.If not,please ignore.
NOTE:
Cooling only unit do not have displays and functions related with heating
4
Outdoor Unit
1
4
Indoor Unit
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
1
2
3
4
Remove the battery cover;
Load the batteries as
illustrated. 2 R-03 batteries,
resetting key(cylinder);
Be sure that the loading
is in line with the" + "/"-";
Load the battery,then put on the cover again.
The distance between the signal transmission head and the
receiver hole should be within 7m without any obstacle as well.
When electronic-started type fluorescent lamp or change-over
so the distance to the indoor unit should be shorter.
wireless telephone is installed in the type fluorescent lamp or
room, the receiver is apt to be disturbed in receivingthe signals,
Note:
Full display or unclear display during operation indicates the
ries have been used up.Please change batteries.
If the remote controller can't run normally during operation,
reload several minutes later.
batte
remove the batteries and
Remove the batteries in case unit won't be in usage for a long period.
If there are any display after taking-out, just need to press reset key
Hint:
Loading of the battery
please
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
or decrease 1min. If the button is kept pressed,time will
will increase
Ope
r
ation mode AUTO
FAN
COOLDRY
Remote controller
Display board
HEAT
settings.
7
(inside)
Anion generator
7
1
2
3
This function is unavailable on
some models.
This function is unavailable on
some models.
(This function is unavailable on
some models.)
(This function is unavailable on
some models.)
1