Haier DWL 2825 D00 User Manual - page 23
22
HEATED DRY
Select this option to dry dishes with heat.
Not selecting heated dry skips the drying period. If the heated drying period is
not selected the dishes take longer to dry and some spotting can occur. For best
drying, always use a liquid rinse aid. Some items (such as plastics) may need
towel drying.
NOTE: Heated Dry is an option with Pots and Pans Wash, Normal and China/
Crystal cycles. For faster air drying, you can open the door a couple of
inches after the final rinse is complete.
STEAm OPTION
Use for all dish loads, including extra large loads. Steam is generated early in
the cycle to help wet baked on soils from dish load and soften it for easier remov-
al by the wash system. The steam cycle raises the temperature in the final rinse to
150ºF (66ºC).
NOTE: This option can be used with all cycles except Rinse and Hold and Speed
cycle.
DELAY HOURS (select models)
Select this option to run your dishwasher at a later time or during off-peak hours.
You can add items to the load anytime during the delay countdown. After adding
items, close the door firmly until it latches.
You can delay the start of a cycle up to 9 hours in 3 hour increments (3, 6, or 9 Hr)
To delay the start
1. Open the door
2. Repeatedly press "Delay Hours until you see the desired hours of delay lighted
in LED indicator on the left. When the delay reaches 9 hours, the delay turns
off. Press "Delay Hours" again to select a new number of delay hours.
3. Select a wash cycle and options
4. Close the door
NOTE: To cancel the delay and cycle, press Cancel. To Cancel the delay and
start the cycle immediately, press Delay Start until there is no light in any
of LED indicators on the left.
DWL3525 WHITE VERSION-160780101
DWL4035 WHITE VERSION-160860101
DWL7075 WHITE VERSION
-160870101
0120400017
SEE NOTES
0
0
ENTER DESCRIPTION
THIRD ANGLEPPROJECTION
A2
DRAFT WHERE APPLICABLEP
MUST REMAINP
WITHIN DIMENSIONS
SYMBOLS
QUALITY
ANGULAR
INCH
mm
=
=
EC NO:
DR
WN:
CH
'KD:
APPR:
DESCRIPTION
REV
SIZE
SCALE
DESIGN UNITS
DIMENSION STYLE
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX
INCORPORATED AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SHEET NO.
DOCUMENT NO.
MATERIAL NO.
APPROVED BY
DATE
CHECKED BY
DATE
DRAWN BY
DATE
TITLE
C
MOLEX INCORPORATED
GENERAL TOLERANCESP
(UNLESS SPECIFIED)
1 OF 1
molex
+0.1
mm
Michael 2009/07/06
E-160XX-101
1:1
mm
GRAPHIC OVERLAY
USE ONL
Y
PRE-RELEASE
REFERENCE
tb_frame_A4_P_ME_TPRev. D 2004/04/02
E
D
C
B
E
D
C
B
A
1
2
3
4
5
6
1
2
3
4
5
6
7
A
1 PLACE
2 PLACES
3 PLACES
4 PLACES
+0.75
+0.25
WHITE FROST(X16)
1
PANTONE COOL GRAY 9C
TRANSPARENT SMOKE
PANTONE 1805C
PANTONE 427C
PANTONE COOL GRAY 3C
BACKGROUND:WHITE COLOR
BUTTON BACKGROUND:PANTONE 427C
BUTTON TOP & BOTTOM:PANTONE COOL GRAY 3C
FONTS:PANTONE COOL GRAY 9C
RED:PANTONE RED 1805C
LED WINDOW:WHITE FROST.
7-SEGMENT DISPLAY WINDOW:TRANSPARENT SMOKE
DWL3525 WHITE VERSION-160780101
DWL4035 WHITE VERSION-160860101
DWL7075 WHITE VERSION
-160870101
0120400017
SEE NOTES
0
0
ENTER DESCRIPTION
THIRD ANGLEPPROJECTION
A2
DRAFT WHERE APPLICABLEP
MUST REMAINP
WITHIN DIMENSIONS
SYMBOLS
QUALITY
ANGULAR
INCH
mm
=
=
EC NO:
DR
WN:
CH
'KD:
APPR:
DESCRIPTION
REV
SIZE
SCALE
DESIGN UNITS
DIMENSION STYLE
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX
INCORPORATED AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
SHEET NO.
DOCUMENT NO.
MATERIAL NO.
APPROVED BY
DATE
CHECKED BY
DATE
DRAWN BY
DATE
TITLE
C
MOLEX INCORPORATED
GENERAL TOLERANCESP
(UNLESS SPECIFIED)
1 OF 1
molex
+0.1
mm
Michael 2009/07/06
E-160XX-101
1:1
mm
GRAPHIC OVERLAY
USE ONL
Y
PRE-RELEASE
REFERENCE
tb_frame_A4_P_ME_TPRev. D 2004/04/02
E
D
C
B
E
D
C
B
A
1
2
3
4
5
6
1
2
3
4
5
6
7
A
1 PLACE
2 PLACES
3 PLACES
4 PLACES
+0.75
+0.25
WHITE FROST(X16)
1
PANTONE COOL GRAY 9C
TRANSPARENT SMOKE
PANTONE 1805C
PANTONE 427C
PANTONE COOL GRAY 3C
BACKGROUND:WHITE COLOR
BUTTON BACKGROUND:PANTONE 427C
BUTTON TOP & BOTTOM:PANTONE COOL GRAY 3C
FONTS:PANTONE COOL GRAY 9C
RED:PANTONE RED 1805C
LED WINDOW:WHITE FROST.
7-SEGMENT DISPLAY WINDOW:TRANSPARENT SMOKE