Service manual this service information is designed for experienced repair technicians only and is not designed for use by the general public. It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products powered by ele...
Service manul model no.Hltd500acw contents chapter 1 general information ________________________________________________ 1-1. General guidelines _____________________________________________________ 1-2. Caution and warning symbols ____________________________________________ 1-3. Function indicati...
7-5. Location of your dryer _________________________________________________ 7-6. Manufacation (mobile) home installation __________________________________ 7-7. Electrical installation __________________________________________________ 7-8. Electrical connections chapter 8 wiring circuit and elect...
Chapter 1 general information 1-1. General guidelines when servicing, observe the original lead dress. If a short circuit is found, replace all parts which are overheated or damaged by the short circuit. After servicing ,see to it that all the protective devices such as insulation barriers ,insulati...
Chapter 2 product feature 2-1. Features (1). Humidity sensor for automatic drying performance. Automatic cycles allow you to match the cycle to the load you are drying. A humidity sensor detects the moisture in the load and automatically adjusts the drying time for optimal drying. (2). 5-temperature...
Service manul model no.Hltd500acw issue rev. - 5 - safety systems motor overheating protection mop 4. Child protection - programs sanitize,heavy duty,normal,eco dry,perm press,delicate n° air dry,touch up,quick dry,timed dry 5. - 4 - optional function keys (additional program settings) power,start/p...
Chapter 3 matters needing attention 3-1. Safety service manul model no.Hltd500acw issue rev. - 6 - important safety instructions before beginning installation, carefully read these instructions. This will simplify the installation and ensure the dryer is installed correctly and safely. Note 1 :the e...
Service manul model no.Hltd500acw issue rev. - 7 - 10.Do not use heat to dry articles or products to eliminate static unless recommended by the manufacturers of the fabric softener or product. 11.Clean lint screen before or after each load. 12.Keep area around the exhaust opening and adjacent surrou...
Service manul model no.Hltd500acw issue rev. - 8 - 2. The dryer must not be exhausted into any gas vent, chimney, wall, ceiling attic, crawl or any concealed space of a building.The dryer exhaust system must be exhausted to the outdoors.If the dryer is not exhausted outdoors, some the laundry area. ...
Chapter 4 operational guidance service manul model no.Hltd500acw issue rev. - 9 - understanding the control panel dry level button when the dryer is first powered on, the cycle status lights indicate the stages of the selected cycles. As the dryer is operation,the active stage blinks.As a stage is c...
Service manul model no.Hltd500acw issue rev. - 10 - wrinkle saver button at the end of the cool down cycle,the dryer will periodically tumble for 1 hour to prevent wrinkles from setting in your garments. Use this button to extend the feature for 150 minutes or to turn the wrinkle saver feature off. ...
Service manul model no.Hltd500acw issue rev. - 11 - k cycle guide note: to protect your garments,all options and settings are not available for all cycles. The sharded boxes indicate the default settings for each cycles. Damp signal button use this button to select or deselect damp signal.The damp s...
Chapter 5 drying mathods 5-1. Preparations before drying service manul model no.Hltd500acw issue rev. - 12 - sort clothes of the same kind (cotton, synthetics, woolen) to dry. Dark and light colored clothes should be separately dried. Fabrics prone to losing lint and those prone to adhering lint sha...
Chapter 6 appearance brief introduction 6-1. Name of parts 6-2. Net dimension power line height:1080mm / width:686mm / depth:777mm service manul model no.Hltd500acw issue rev. - 13 - knob.
Chapter 7 disassembly and installation 7-1. Remove packing materials 7-2. Exhaust requirements service manul model no.Hltd500acw issue rev. - 14 - unpacking your dryer: 1. Remove all packaging material. This includes the foam base and all adhesive tape holding the dryer accessories inside and outsid...
7-3. Adjusting the dryer 7-4. Electrical requirements service manul model no.Hltd500acw issue rev. -15 - recommended maximum exhaust hood types recommended use only for short run installations no. Of 90 o elbows rigid metal flexible metal rigid metal flexible metal . T f 0 6 . T f 0 9 0 . T f 5 4 . ...
7-5. Location of your dryer service manul model no.Hltd500acw issue rev. - 16 - dryers being installed in a manufactured (mobile) home must employ a 4- wire power supply cord nema 14-30 type srdt or st (as required) rated to 240 volt ac minimum, 30 amp, with 4 open-end spade lug connectors with uptu...
7-6. Manufacation (mobile) home installation 1). Dryer must be exhausted outside ( outdoors, not beneath the manufactured home) using metal ducting that will not support combustion. Metal ducting must be 4 inch (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. 2). If dryer ...
Service manul model no.Hltd500acw issue rev. - 18 - 7-7. Electrical installation 1.This appliance must be properly grounded. Electrical shock can result if the dryer is not warning:the following are specific requirements for proper and safe electrical installation of your dryer. Failure to follow th...
Service manul model no.Hltd500acw issue rev. - 19 - 2.Insert a ul listed strain relief into the mounting bracket hole. Position the strain relief so that one tab is pointing up and one tab is pointing down. Tighten the strain relief screws just enough to hold the two halves together. Tab strain reli...
Service manul model no.Hltd500acw issue rev. - 20 - a1. Remove the green ground screw connecting the neutral-ground jumper wire white) to the cabinet and the center terminal block screw, then discard the jumper wire. A2. Attach the power cord ground wire (green) to the cabinet with the green ground ...
Service manul model no.Hltd500acw issue rev. - 21 - chapter 8 wiring circuit and electric appliances parameter 8-1. Wiring circuit 8-2. Electric appliances parameter part name reference number in sbom parameter remark motor door switch control pcb display pcb high limit thermostat heater thermal lim...
Chapter 9 error display and troubleshooting 9-1. Error display service manul model no.Hltd500acw issue rev. - 22 - 9-1-1. The digital tube display “f3” troubleshooting: connect the wire properly n y error message:ntc1 is abnormity . Check if the wire connecting of the ntc1 and pcb is disconnection; ...
9-1-3. The digital tube display “f4” error message:heater is abnormity . Troubleshooting: cut off the power. Check if the power line is well and connected properly replace the power line or connect the power wire properly connect the wire properly replace the heater check if the wire connecting of t...
Service manul model no.Hltd500acw issue rev. - 24 - 9-2. Examination & troubleshooting 9-2-1. The computer is power on and display right,but the dryer no action troubleshooting: cut off the power .Check if the door of the dryer is closed? Close the door. Check if the belt is correctly installed? Cor...
Service manul model no.Hltd500acw issue rev. - 25 - 9-2-2. Display nothing troubleshooting: measure the power supply ,is it exists 120v/240v ac voltage repair power supply connect the wire properly cut off the power. Check if the power line connecting between the dryer and the power supply cord is o...
Service manul model no.Hltd500acw issue rev. - 26 - 9-2-4. Use the “automatic cycles” program the dryer is drying but the clothes can’t intensive drying end the program troubleshooting: check system are good? If the external and inner exhaust clean or repair the external and inner exhaust system. N ...
Service manul model no.Hltd500acw issue rev. - 27 - 9-2-6. Too much abnormal noise in drying 9-2-7. The lamp is not bright when open the door troubleshooting: search the root of the noise. Check if is there grating between the impeller and the worm shell? Fasten the screw check if the drum touch som...
Service manul model no.Hltd500acw issue rev. - 28 - 9-2-8. The barrel is continuing runing after opening the door troubleshooting: well:the you can replace it or use ohmmeter,when the door is open, you can use ohmmeter to measure just as the picture show. Resistence is infinite; well check if the do...
Service manul model no.Hltd500acw issue rev. - 29 - chapter 10 maintenance lint filter needs to be cleaned before or after each use for your unit to operate at optimum efficiency. The filter can be removed by pulling on the tabs located on the inside of the dryer door. The filter may be washed or va...
Sincere forever haier industrial park, no.1, haier road 266101, qingdao, china http://www.Haier.Com printed in china h ier group.
