Haier RDE350AW - 6.5 Cu. Ft. Electric Dryer Service Manual

Other manuals for RDE350AW - 6.5 Cu. Ft. Electric Dryer: User Manual, User Manual And Installation Instructions
Manual is about: Gas and Electric Clothes Dryers

Summary of RDE350AW - 6.5 Cu. Ft. Electric Dryer

  • Page 1

    Features: electrionic control front door design 3 drying cycles 4 temperatures setting end of drying signal wrinkle care program electric clothes dryer service manual rde350aw serial number :rde350aw edition: 2008-08-08 model: version: a 8.

  • Page 2

    Contents 1. Specifiation list ………………………………………………………………………1 2. Dimensional drawing ……………………………………………………………… 1 3. Circuit diagram …………………………………………………………………… 2 4. Names of parts …………………………………………………………………… 2 5. Usage of the operation knobs………………………………………… ………… 3 6. Products brief and new features ………………...

  • Page 3

    Model about 59kg l 686mm w 718mm h 1080mm programs rde350aw 120v/240v 60hz 10kg(weight of standard dry cloth) setting drying program according to the laundries automatically the time for setting : 30 min, 60 min, 90 min, 120 min user's manual , product registration card rated voltage·rated frequency...

  • Page 4

    2 3 circuit diagram circuit diagram control plate front plate front door control panel shutter exhaust duct back baffle nameplate cabinet adjustable foot thread-protected board i thread-protected board ii fasten button whisk leaf barrel roll lint filter lock body electric clothes drye r model:rde350...

  • Page 5

    3 warning: to reduce the risk of fire, electric shock or injury to persons, read the important safety instructions before operating this dryer. Understanding the control panel cycle select diail: (2) start/pause button: (4) select the from 3 auto-dry cycles (heavy duty, normal, and delicates), or 4 ...

  • Page 6

    4 3) power transmission system during drying, motor 1 transmits the driving power to tumbler 5 through belt 2 and multi-wedge belt 3. Then tensioning wheel 4 tensions the belt under the action of tensioning spring. At the same time, it also increases the transmission wrap angle of the pulley, and im...

  • Page 7

    5 dry sensor: (feature only active in auto dry cycle) end of cycle signal: lint filter: leveling legs: your dryer also has the following features for your convenience: c new features this senses temperature in the drum. The dryer will automatically shut itself off. Your dryer is equipped with an aud...

  • Page 8

    96 power supply: power supply cord kit: 3 wire , 120 volt , 30 amp, 60hz, 1 phase (not supplied when sold in the united states) the dryer must employ a 3-conductor power supply cord nema 10-30 type srdt rated at 120 volt ac minium, 30 amp, with 3 open end spade lug connectors with upturned ends or c...

  • Page 9

    97 after installation is completed, the following method must be used to determine if the exhaust system is acceptable: although vertical orientation of the exhaust system is acceptable, certain extenuating circumstances could affect the performance of the dryer: the exhaust system should be inspect...

  • Page 10

    9 8 c installation in mobile home dryer must be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 inches (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. If dryer is exhausted through the...

  • Page 11

    9 3-wire cord connections 8 danger : improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. The dryer must be connected to a grounded metal, permanent w...

  • Page 12

    9 11 8.2 the tub rotates but does not dry 8.3 the machine dries but the tub does not rotates switch on the power, push down the start button switch on the power, push down the start button set timed drying (above 15 min) yes no no yes observe wether the heater is aglow from the back of the machine (...

  • Page 13

    9 10 8 analysis of the common breakdowns if you replace the thermal limiter or program controller without checking the other components carefully, the thermal limiter or program controller may be damaged again. Therefore, please first check if the other components working normally before replacing t...

  • Page 14

    9 12 8.4 too much noise in drying the noise includes the harsh , the metallic bang and the big collision sound during drying , these are normal sounds such as vent-like sound and a grating ect. Switch on the power, push down the start button search the root of the noise check if these come from the ...

  • Page 15: Group

    Group sincere forever haier industrial park, no.1, haier road 266101, qingdao, china http://www.Haier.Com.