- DL manuals
- Holman
- Irrigation System
- RSR
- Instruction Manual
Holman RSR Instruction Manual
Summary of RSR
Page 1
Instruction manual suitable for indoor use only otherwise warranty is void irrigation controller 6 station model.
Page 2
Page 1 this unit is available as a 6 station configuration. Designed for residential and light commercial applications, this controller has four separate programs with up to sixteen possible start times a day. This ensures efficient watering of different garden or turf areas. These different areas m...
Page 3
Page 3 programming instructions introduction this controller has been designed with four separate programs, to allow different garden areas to have their own individual watering requirements. A program is basically a method of grouping stations (valves) with similar watering requirements to water on...
Page 4
Page 5 programming instructions programming instructions programming example in this example, the lawn areas , program 1 ( group 1 ), are using pop-up sprinklers & require less frequent watering. The vegetables are being watered using drippers on a longer run time, with the flower beds, pots, hangin...
Page 5
Page 7 before proceeding, ensure your watering planner has been completed. From this, you should be aware of which stations are allocated to each program. Note: set one program at a time -this will ensure that all the values are entered correctly. Setting program 1 - the program number can only be s...
Page 6
Page 9 programming odd / even day selection (optional) in some regions, users are only allowed to water their gardens on, odd dates if their house number is odd, or on even dates when their number is even . This controller allows this to be done simply by setting the relevant selection of odd or eve...
Page 7
Page 11 manual operations programming step 3. Set station run times. (continued) to adjust the run time in minutes press next , and use or . To set the run time in hours, press next and “0” will appear and flash. To adjust use or . If not required, press next and advance to station 2 by pressing the...
Page 8
Page 13 rain sensor ready this feature should only be used when a rain sensor has been connected. The controller comes pre-fitted with a socket, ready to take the “holman” rain sensor (p/n crs1000bc, not included) which has also been pre- fitted with a plug. Simply push the plug into the socket and ...
Page 9
Rain sensor ready (cont.) delay feature - when using the rain sensor ready feature, in conjunction with the rain sensor. It is possible to set a delay in the controller to stop the automatic programs from activating too quickly. This feature is applicable to the stations nominated to be controlled b...
Page 10
Installation instructions mounting the controller this controller unit is an indoor model and must not be exposed to rain or water ingress. (if the controller needs to be outdoors, you can purchase a holman outdoor weatherproof box, p/n cobox, to mount the controller inside.This box is available fro...
Page 11
Installation instructions power supply connections the controller itself can run off a 240v ac to 24v ac external transformer.. It is recommended that the transformer is not connected to a 240v ac supply which is also servicing or supplying motors (i.E. Air conditioners, pool pumps, refrigerators, e...
Page 12
Electrical characteristics power supply mains supply this unit can run off a 50hz external transformer, (plugpack), with an output of 24vac 50hz @ 1 amp. Plug pack model the correct wiring installation for the 24vac plug pack is shown on page 19. The plug pack model is only suitable for indoor insta...
Page 13
Possible cause faulty transformer. Fuse blown. Faulty solenoid coil. Incorrect wiring or bad wiring joint. Incorrect programming or blown fuse. Short on keypad or programming not correct. Short on keypad or too many start times entered on automatic programs. Damaged main output driver chip. Faulty r...
Page 14
Spare watering planner page 25 page 24 spare watering planner.
Page 15
Your guarantee the manufacturer guarantee to the original purchaser that any product supplied by the manufacturer will be free from defects in materials and workmanship for a period of three years from the date of purchase. Any product found to have defects in material or workmanship within the peri...