Home Automation Digital Whole Home Audio Distribution System User Manual
Summary of Digital Whole Home Audio Distribution System
Page 1
User’s guide digital whole home audio distribution system document number 62r00-1 rev a october, 2006.
Page 2
Copyright © 2006 home automation, inc. All rights reserved.
Page 3
Precautions exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably to noise induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The u.S. Government's occupational safety and...
Page 4: Contents
Contents introduction ........................................................................................................................1 general ................................................................................................................................................... ...
Page 5: Introduction
Page 1 introduction thank you for purchasing your new hi-fi by hai audio distribution system. You are about to enjoy the freedom and convenience of listening to and sharing music from your stereo, ipod™, satellite radio, digital cable tv, computer, cd player, or any other music source in any room in...
Page 6: Operation
Page 2 operation when an audio zone is turned on and the volume-source control (vsc) in that zone is idle, the blue display will show the current volume level of the zone. Volume push to select vsc you can change the zone power on/off state, select an alternative audio source, and adjust the zone vo...
Page 7
Page 3 all zones off if you wish to turn all zones off, press the knob and hold it for 3 - 5 seconds. Release the knob when the display shows "ff". All zone amplifiers are turned off and the volume for each zone is set to "00". Setting zone volume turning the knob on the vsc clockwise will increase ...
Page 8
Page 4 display system setting default value range ba bass 0 -9 to 9 tr treble 0 -9 to 9 bl balance 0 -9 to 9 if there is no interaction with the vsc for more than 20 seconds, the menu will be exited and the display will revert back to the volume setting. You can also manually exit from the zone menu...
Page 9
Page 5 advanced menu to adjust the source gain and the connection status of each source, whether ir is enabled or disabled, whether ir is passed to the audio sources, zone groups, and paging volume, press and hold the knob on the vsc for more than 5 seconds to enter the advanced menu. Release the kn...
Page 10
Page 6 setting source gain / connection status the source gain / connection item allows you to change the source gain setting for each of the six sources. These settings are system-wide and affect all zones. To change the source gain for source 1, turn the knob when "g1" is displayed. Turning the kn...
Page 11
Page 7 ir enable / disable this menu item allows you to set whether the ir information received at the vsc is sent to the hi-fi processor. By default ir is enabled, thus allowing the vsc to route the information to the hi-fi processor whenever an ir signal is received. To change the ir setting, turn...
Page 12
Page 8 power + - 6 5 4 3 2 1 source mute volume 1 2 3 4 5 ir receive when an ir signal is received by the vsc, it is sent directly to the hi-fi processor. Upon receiving the ir data, the hi-fi processor will decode it and process certain commands locally and route all ir data to connected source equ...
Page 13: Rim
Page 9 ir passthrough when ir passthrough is enabled, ir data can also be routed to the connected source equipment. After decoding the received ir, the hi-fi processor will then route the ir signal to the source which is logically connected to that vsc. Ir output each rim ships with an ir flasher (6...
Page 14: Rim
Page 10 rim remote input module hi-fi rim audio in ir out source 2 mp3 player connecting your music source each remote input module (rim) located throughout your house is used to pick up music from your home theater, kitchen tv, computer, personal music player, satellite radio, media center, cd play...
Page 15: Page / Mute
Page 11 page / mute hi-fi has the capability of playing audio over all speakers in your home in special circumstances. For example, it can announce when someone is at the door or when the telephone is ringing. This feature is called paging. If paging is used, the paging audio source will be connecte...
Page 16
Hai • new orleans, la • u s a.