- DL manuals
- I-Data
- Printer Accessories
- 812-1x MIO
- Operator's Manual
I-Data 812-1x MIO Operator's Manual - Scalable Fonts
ida 812-1x MIO Operator’s Guide
Font Selection
-39-
Scalable Fonts
NOTE:
Only applies to printers running PCL Level 5
.
The ida 812-1x MIO allows GFID access to all the scalable fonts
found in the printer. These GFIDs are in the range 400 - 65535.
Typeface, typeface attributes and point size have been linked
together using the system described below.
GFID Number = XXXYY
where XXX = point size
and YY = typeface + attribute
Possible typeface values are:
Typeface
ID
PCL No.
Name of Typeface
0
5
CG Times Roman
4
4116
Coronet
10
4
Helvetica
14
36
Helvetica Narrow
20
23
Century Schoolbook
24
4297
Marigold
30
17
Humanist / CG Optima
34
4168
Antique Olive
40
31
ICT Avant Garde
44
4197
Garamond Antique
50
16901
Times New Roman
54
16602
Arial
60
52
Univers
Summary of 812-1x MIO
Page 1
I-data electronic documentation ida 812-1x mio operator’s guide doc. No d60222 revision 01 i-data international a-s • vadstrupvej 35-43 • 2880 bagsværd • denmark phone: +45 44 36 60 00 • fax: +45 44 36 61 11 • www: http://www.I-data.Com • e-mail: i-data@i-data.Com warning: this equipment generates, ...
Page 2
-2- document no.: d60222-01 © copyright i-data international a-s 1997 main office: i-data international a-s vadstrupvej 35-43 dk-2880 bagsvaerd denmark telephone: +45 44 36 60 00 telefax: +45 44 36 61 11 subsidiaries i-data denmark vadstrupvej 35 dk-2880 bagsvaerd denmark telephone: +45 44 44 77 50 ...
Page 3: Preface
Ida 812-1x mio operator’s guide preface -3- preface september 1997 this manual applies to the ida 812-1x mio, i.E. The following printers equipped with an i-data plug-in interface with firmware release no: s21 112.070 or higher. • hp laserjet iiisi • hp laserjet 4 • hp laserjet 4si • hp laserjet 4 p...
Page 4
Ida 812-1x mio operator’s guide preface -4- related manuals "ida 812-1x pcl platform, programmer's guide" document no. D62026. As the ida 812-1x mio emulates the ibm 5219 printer, useful information may be obtained from: "ibm 5219 printer, models do1/do2, programmer's reference guide", ibm order no....
Page 5: Table of Contents
Ida 812-1x mio operator’s guide table of contents -5- table of contents preface................................ ................................ ................................ ........... 3 prerequisite manuals ................................ ................................ .3 table of contents....
Page 6
Ida 812-1x mio operator’s guide table of contents -6- 5.2.4. Setup menu ................................ ................................ ..29 5.2.5. Save/restore menu ................................ .................. 29 6. Errors and recovery................................ .........................
Page 7: 1.2. Ida 812-1X Mio Features
Ida 812-1x mio operator’s guide introduction -7- 1. Introduction to the ida 812-1x mio 1.1. What is the ida 812-1x mio the ida 812-1x mio is a printer with an interface de signed for use with the displaywrite/36, office/38, office/400, tms and similar programs. The ida 812-1x mio emulates the ibm 52...
Page 8
Ida 812-1x mio operator’s guide introduction -8- • up to 24 pages per minute • laser quality printout • printer sharing with automatic switching and setup • automatic font change • scalable fonts • proportional spacing • internally generated bar codes which can be accessed via gfid or via escape seq...
Page 9
Ida 812-1x mio operator’s guide introduction -9- settings (the hp mio printer’s) or be over written from the syst em and cause formatting problems (see chapter 5 front panel setup). 1.4. How the ida 812-1x mio works the ida 812-1x mio works using 26 internal setup func tions. These setup functions a...
Page 10
Ida 812-1x mio operator’s guide installation -10- 2. Installing the ida 812-1x mio interface before you start the installation, make sure that the kit is complete. It should contain the following items: • ida 812-1x mio interface • auto-terminating t-cable • "ida 812-1x mio, operator's guide"; docum...
Page 11: 2.2. European Or Us Defaults
Ida 812-1x mio operator’s guide installation -11- the possible values are: • international • united states • austria/germany • belgium • brazil • canada/france • denmark/norway • finland/sweden • france • italy • iceland • japan (english) • portugal • spain • spanish speaking • united kingdom • mult...
Page 12: 2.3. Installation Procedure
Ida 812-1x mio operator’s guide installation -12- 2.3. Installation procedure the installation of the ida 812-1x mio interface varies slightly depending on the printer in which it is installed. This is decribed in more detail below. Note: irrespective of printer, you should first make sure that powe...
Page 13
Ida 812-1x mio operator’s guide installation -13- 2.3.4. Hp laserjet 5si 1. Loosen the screws and remove the plate of the top slot positioned on the rear of the printer. 2. Insert the ida 812-1x mio interface in the slot and tighten screws. 2.3.5. Hp paintjet xl300 1. Loosen the screws on the cover ...
Page 14: 3.1. Power Connection
Ida 812-1x mio operator’s guide installation -14- 3. Installing the ida 812-1x mio printer the installation of the ida 812-1x mio printer is similar to the installation de scribed in the origina l hp manuals, except for the twinax cable connection of the ida 812-1x mio to the host system (see sectio...
Page 15: 3.3. Twinax Connection
Ida 812-1x mio operator’s guide installation -15- 3.2. Printer configuration procedure 1. Set the device address on the switch located on the rear panel next to the twinax connector. Possible values are 0 to 6. Make sure that the device address is set before the twinax cable is connected. 2. Select ...
Page 16: 3.4. Printer Emulations
Ida 812-1x mio operator’s guide installation -16- warning! The twinax cable must never be connected directly to the twinax socket of the printer. It must always be connected to the t-cable. 3.4. Printer emulations on the ida 812-1x mio it is possible to emulate the following ibm printers once the in...
Page 17: 3.5. System Configuration
Ida 812-1x mio operator’s guide installation -17- 6. Turn printer power off and set the device address switch as described in section 3.2, printer configuration procedure and according to the new emulation. 7. Connect the twinax cable and turn printer power on. 3.5. System configuration to obtain ac...
Page 18: 4. Ida 812-1X Mio Operation
Ida 812-1x mio operator’s guide operation -18- 4. Ida 812-1x mio operation the ida 812-1x mio is controlled entirely from the host system by ibm commands and requires very little operator intervention. The configuration of the printer may be changed from the system with function selection via the li...
Page 19: 4.2. The Test Key
Ida 812-1x mio operator’s guide operation -19- the par.Data indicator led has 2 states which indicate the follow- ing: state indication off parallel interface inactive. On parallel interface active. 4.2. The test key as previously mentioned, tests are primarily selected via the line. However, the [t...
Page 20
Ida 812-1x mio operator’s guide operation -20- if data is sent on the twinax line, the module will enter twinax session mode. If no data is sent via the twinax line within the specified timeout period, parallel data may be printed. This also applies if the module is in twinax session mode. Note: bec...
Page 21: 5. Front Panel Setup
Ida 812-1x mio operator’s guide front panel seup -21- 5. Front panel setup this chapter describes the setting up of the ida 812-1x mio interface via the printer's front panel. Setting up via the front panel provides an alternative to setting up fsl functions. But please note that the front panel onl...
Page 22
Ida 812-1x mio operator’s guide front panel seup -22- front panel setup for the ida 812-1x mio 2 ipds emulation codepage version cpgid font margins to system vpa check im smooth print offset save menu duplex memory autoconfiguration true page counter setup menu hp main menu save settings restore sel...
Page 23
Ida 812-1x mio operator’s guide front panel seup -23- 5.1.1. Navigation keys the following guidelines apply after you have entered the main menu for ida 812-1x setup (see navigation chart above). The keys you use to navigate vary slightly depending on the printer; e.G.: to go to next menu on hp lase...
Page 24
Ida 812-1x mio operator’s guide front panel seup -24- mark with an asterisk *: press enter go to next setting: press item save settings: after change of settings, you toggle to save menu using item key and press enter. Save sett.= no* will appear in the display. To select yes, you press + or - key. ...
Page 25: 5.2. Sub-Menus
Ida 812-1x mio operator’s guide front panel seup -25- 5.2. Sub-menus below is a more detailed description of the individual sub-menus. The factory default settings are marked with an asterisk ( *). In the front panel display, the asterisk will mark the currently selected value. 5.2.1. Non-ipds menu ...
Page 26
Ida 812-1x mio operator’s guide front panel seup -26- lines per inch (lpi) corresponds to fsl-function y2. Possible selections are: 0 3lpi 4lpi *6lpi 8lpi characters per inch (cpi) corresponds to fsl function y3. Possible selections are: 5 cpi *10 cpi 12 cpi 15 cpi 16 cpi codepage corresponds to fsl...
Page 27
Ida 812-1x mio operator’s guide front panel seup -27- emulation possible selections for emulation are: *3812 includes 3816 5224 5225 5256 4234 ipds 3 ip1k 1k ipds data buffer support note: after making changes to emulation via the front panel (remember to save via the save menu), you must switch off...
Page 28
Ida 812-1x mio operator’s guide front panel seup -28- 5.2.2. Test menu the "test menu" contains all test print functions and dump mode functions. Selected test functions are executed when the printer is ready for printing. Several tests can be selected at the same time. Settings printout (no/yes) "s...
Page 29
Ida 812-1x mio operator’s guide front panel seup -29- paper size "size=" defines the size/type of paper in the present tray and the extents and margins that will be reported back to the host system. Possible values are: "letter" "legal" "a4" "executive" “ledger” “a3” (hp laserjet 4v only) "monarch" ...
Page 30: 6. Errors And Recovery
Ida 812-1x mio operator’s guide errors and recovery -30- 6. Errors and recovery 6.1. Error messages in mio front panel the 80_service (01xx) error message will be displayed in the mio front panel if the following error situations occur: recovery attempt can be made as follows: • turn power off for 1...
Page 31: 6.2. Error Messages On Paper
Ida 812-1x mio operator’s guide errors and recovery -31- downloaded firmware again no invalid boot id in hex data 8e you have tried to download a firmware not meant for this product attempt to write to boot area 90 firmware code error. A correction to the firmware code is needed get correction to fi...
Page 32: 7.1. The Escape Character
Ida 812-1x mio operator’s guide function selection via the line -32- 7. Function selection via the line note: this section is a brief description of how to set up the interface from the line with fsl functions. The section is primarily intended for users who are already familiar with i-data products...
Page 33
Ida 812-1x mio operator’s guide function selection via the line -33- an esc character can be any character you wish, but before you define it you should consider the following: • once the esc character has been defined, it cannot be printed. For this reason it is advisable to select a character you ...
Page 34: 7.5. Invalid Escape Sequence
Ida 812-1x mio operator’s guide function selection via the line -34- 7.3. Syntax of an fsl function the special sequence that the interface will interpret as an fsl function is shown in figure 7-3. %y,% fig. 7-3: syntax of an fsl function. "%" is the defined esc character 7.4. Supported fsl function...
Page 35
Ida 812-1x mio operator’s guide fsl setup via pc’s parallel port -35- 8. Fsl setup via pc's parallel port in order to ease customization of the ida 812-1x, fsl parame ters for twinax input can be programmed directly via the interface's centronics port using the engineering function y249. The enginee...
Page 36: 8.1. Updating Firmware
Ida 812-1x mio operator’s guide fsl setup via pc’s parallel port -36- deactivating the y249 engineering function the function will be deactivated automatically after timeout on the share port (timeout is defined in y100 port sharing option). Limitations when y249 is active 1. Escape sequences must b...
Page 37: 9. Font Selection
Ida 812-1x mio operator’s guide font selection -37- 9. Font selection the factory default gfid table below lists all the predefined fonts which are supplied with the interface gfids (gfids 1 - 399) 6 . Fonts with gfids above 400 (i.E. Scalable fonts) are described in the section scalable fonts below...
Page 38
Ida 812-1x mio operator’s guide font selection -38- in the table below, an asterisk (*) after the gfid number denotes a simulated ibm gfid. Gfid font type- face attri- bute symbol set point size translate table 3* ocr b 0 0 7 12 7 11* courier 3 0 1 12 1 12* prestige 8 0 1 10 1 18* courier italic 3 2...
Page 39: Scalable Fonts
Ida 812-1x mio operator’s guide font selection -39- scalable fonts note: only applies to printers running pcl level 5 . The ida 812-1x mio allows gfid access to all the scalable fonts found in the printer. These gfids are in the range 400 - 65535. Typeface, typeface attributes and point size have be...
Page 40
Ida 812-1x mio operator’s guide font selection -40- possible attribute values are: style strokeweight 0 medium upright 1 bold upright 2 medium italic 3 bold italic %y96,4815% this is 48 point, helvetica narrow, bold upright %y96,1301% this is 13 point, times roman, bold upright font examples other r...
Page 41: 10. Test Settings Printout
Ida 812-1x mio operator’s guide test settings printout -41- 10. Test settings printout ida 812-1x mio, firmware version: s21 112.070/00206062 i-data international a-s vadstrupvej 35-43 2880 bagsvaerd, denmark phone: +45 44 366000 fax: +45 44 366111 boot id: 80003004 hw id: current escape code = 00 i...
Page 42: List of Abbreviations
Ida 812-1x mio operator’s guide list of abbreviations -42- list of abbreviations the following list is an alphabetical list of the abbreviations used in this publication, together with their definitions. Apl a programming language ascii american standard code for information interchange cpi characte...
Page 43: Appendix A - Fsl Functions
Ida 812-1x mio operator’s guide appendix a - fsl functions -43- appendix a - fsl functions no. Function 2 lpi 3 cpi 8 language 10 page format 11 paper path 12 paper size 19 duplex printing 21 horizontal compression 22 printer driver selection 37 ibm printer emulation selection 48 permanent esc chara...
Page 44
Ida 812-1x mio operator’s guide appendix a - fsl functions -44- t(est) functions: t1 = online hex dump t4 = setup printout z function: zn = send user-defined string s function: sn = send user-defined string w function: wn = print barcode x functions: x1 = store settings in the permanent memory x3 = ...
Page 45
Ida 812-1x mio operator’s guide appendix a - fsl functions -45- no. Name syntax parameters 2 lpi %y2,% 3 = 3 lpi 4 = 4 lpi *6 = 6 lpi 8 = 8 lpi 3 cpi %y3,% 5 = 5 cpi *10 = 10 cpi 12 = 12 cpi 15 = 15 cpi 16 = 16.7 cpi 8 language %y8,% **37 = engl. Us ebcdic 38 = ebcdic 256 = international 273 = austr...
Page 46
Ida 812-1x mio operator’s guide appendix a - fsl functions -46- no. Name syntax parameters 12 paper size %y12,[,n2,n3]% n1 (physical paper size) *1 = a4 2 = legal **3 = letter 4 = executive 5 = letter (monarch) 6 = business 7 = intl dl 8 = intl c5 9 = b5 10 = a3 11 = ledger 15 = comm 9 envelope 16 =...
Page 47
Ida 812-1x mio operator’s guide appendix a - fsl functions -47- no. Name syntax parameters 19 duplex printing %y19,% *0 = simplex 1 = long-edge duplex 2 = short-edge duplex 21 horizontal compression extended (vertical linefeed com- pression) %y21,[,n2]% %y21,[,n2,n3]% n1 0 = compression *1 = no comp...
Page 48
Ida 812-1x mio operator’s guide appendix a - fsl functions -48- no. Name syntax parameters 59 bar code type definition %y59,,, ,[,n5]% n1 1-8 = bar code def. No. N2 22-39 = bar code type n3 1-255 = height n4 1-32 = horizontal expansion n5 1-65535 = gfid no. 61 setup for user strings %y61,,% n1 0-7 =...
Page 49
Ida 812-1x mio operator’s guide appendix a - fsl functions -49- no. Name syntax parameters 75 overwrite translate table %y75,[,n2], % n1 40-ff = position in hex of character to be trans- lated n2 1-8 = symbol set defined in fsl 74 n3 00-ff = data in ascii hex required to print the character 88 physi...
Page 50
Ida 812-1x mio operator’s guide appendix a - fsl functions -50- no. Name syntax parameters 90 user esc string definition %y90,,% n1 0 = erase strings 01-ff = string no. In hex n2 '' = string contents in apostrophe nota- tion (see "ida 812-1x pcl platform, program- mer's guide") 91 font definition %y...
Page 51
Ida 812-1x mio operator’s guide appendix a - fsl functions -51- no. Name syntax parameters 92 font point size definition string %y92,,% n1 1-8 = string no in decimal n2 00-ff = string contents in hex 93 font attribute definition string %y93,,% n1 1-8 = string no in decimal n2 00-ff = string contents...
Page 52
Ida 812-1x mio operator’s guide appendix a - fsl functions -52- no. Name syntax parameters 100 port sharing option %y100,[,n2]% n1 0 = resend the settings after share timeout 1-255 = timeout in no. Of sec- onds *20 n2 00-ff = string in hex to be sent to printer before transmission of data when print...
Page 53
Ida 812-1x mio operator’s guide appendix b - dip switch settings -53- appendix b. Dip switch settings language 4 of the 8 dip switches are used to select language and paper size (us/european paper size). The united states/canada and the canada/france 7 switches select letter paper size (i.E. 8.5" x ...
Page 54: Index
Ida 812-1x mio operator’s guide index -54- index —c— connection power, 14 twinax, 15 —d— dip switch, 53 dip switches settings, 53 —e— errors, 30 escape character, 32 temporary, 33 —f— features, 7 front panel aux io menu, 21 codepage (non-ipds), 26 cpi (non-ipds), 26 emulation (non-ipds) , 27 lpi (no...
Page 55
Ida 812-1x mio operator’s guide reader’s comments -55- reader's comments this manual is part of a library that serves as a reference source for programmers and operators of i -data equipment. This form may be copied and used to communicate your view about this publication. Your interest is appreciat...