Welcome to i+me actia ! Before acquainting you with your new i+me hardware we would first like to thank you for purchasing our product. We are extremely pleased that you have chosen to place your trust in i+me actia and will do our best to satisfy whatever needs you may have. The following is a brie...
Whether your professional background is into industry- process-control or development and test tools, we offer six product groups to fulfill your sophisticated needs. Tried and tested under the most severe conditions the automotive industry has to offer, our products have proved themselves again and...
4 can system application software enabling real-time system modeling, testing of networked systems as well as application support. Offering basic services for network communication which is applicable for various processors and programming languages. Facilitating the application interface for distri...
Don’t hesitate to call us and benefit from i+me’s extensive knowledge - your need is our desire. Our merger with the french corporation actia in 1995 allowed us to become a powerful supplier for the european automotive industry. Actia products include diagnostic systems for automotive service and ma...
I+me actia representatives si-kwadraat actia sa nuenen, netherlands toulouse, france t: +31 40 2631185 t: +33 05 61176161 f: +31 40 2838092 f: +33 05 61554231 nohau elek. Ab actia inc. Malmö, sweden bedford, texas usa t: +46 40 592200 t: +1 817 5710435 f: +46 40 592229 f: +1 817 3559513 if needed, p...
Manual netporty ii contents 1 introduction......................................... 1-1 1.1 your i+me netporty ii ......................................1-2 1.2 system requirements ......................................1-4 1.3 delivery contents .............................................1-5 1.3.1 s...
5 glossary .............................................. 5-1 6 literature ............................................. 6-1 a levelx api b levelx demos c pccancontrol administration of document document version: 1.05.
1 introduction your i+me netporty ii. Overview, systemrequirements, delivery contents and s.O..
Introduction your i+me netporty ii version 1.03 1-2 1.1 your i+me netporty ii the netporty ii is an improved portable network adapter. It is designed to connect devices with rs232 or centronics interface to the can bus. With its features it is an ideal general purpose hardware for industrial and aut...
Introduction your i+me netporty ii version 1.03 1-3 i+me actia is always eager to full fill the needs of our customers. If problems should occur, please refer to troubleshooting. If the problem persists, then feel free to contact our after-sales support hotline using the following number: after-sale...
Introduction system requirements version 1.03 1-4 1.2 system requirements pc requirements: • standard pc with rs232 or centronics (epp 1.7 or 1.9) interface • other device with standard rs232 interface (used signals described in chapter hardware).
Introduction delivery contents version 1.03 1-5 1.3 delivery contents 1.3.1 standard your netporty ii delivery package (order code: ime 1602401) includes: • 1 netporty ii • 1 system user manual (hardware/software) • transfer tools to netporty ii • levelx software driver for design of 32 bit windows ...
Introduction technical specifications version 1.03 1-6 1.4 technical specifications general characteristics of netporty ii processor 80c165, @36,84mhz protocol interface 1 x sja1000, @ 16 mhz 1 x 82527, @16mhz 1 x uart physical interface can: according to iso 11898 (pca 82c251) memory 512 x 16 kbyte...
Introduction technical specifications version 1.03 1-7 options memory 64 kb eprom instead of flash physical interface: iso low speed (iso 11519) diagnosis channel iso 9141 physical interface can can optional galvanic disconnect cable 1 m cable for adaptation power supply 230 v/ac to regulated 8 v/dc...
2 installation installing your netporty ii. Step by step installation procedures for hardware and software..
Installation overview version 1.03 2-2 2.1 overview this chapter gives detailed information about installing the netporty ii hardware and about the necessary software drivers which make netporty ii access possible. The netporty ii is delivered with access driver and applications for windows 95 and w...
Installation installing the hardware version 1.03 2-3 it is also necessary to connect the netporty ii with a power supply. Therefore an external power unit can be used to supply the netporty ii via the power connector or via the 9 pin d-sub can-connector. If all connections are done netporty ii is o...
Installation installing the software version 1.03 2-4 2.3 installing the software 2.3.1 if you start at serial port driver installation: 1 insert the cd. The setup programm will start automatic, if not please start the program “start.Exe” in root path. 2 go to "software installation" 3 choose your o...
Installation installing the software version 1.03 2-5 problems: it is possible you chose an incorrect com port. Start pccancontrol again and choose an other com port. 2.3.2 if you start at parallel port 1 make sure that your pc parallel port uses the epp- mode. You have to control it under bios setu...
Installation installing the software version 1.03 2-6 this software is a win32-console-application and runs under win95 and winnt. Usage: - connect your netporty ii with one serial port. - if you do not use com1 please change it into the file l.Bat. - start l.Bat. - if you get error messages like "b...
3 hardware the technical components, there specifications and the way they work together..
Hardware micro controller version 1.03 3-2 3.1 micro controller the i+me netporty ii includes the 16-bit siemens 80c165 micro controller on a piggy back. The controller’s clock frequency is 36,84mhz. The following recourses are used: port 2.14 [ex6in] sja1000 port 2.15 [ex7in] 82527 / 16cs550 cs0-cs...
Hardware memory version 1.03 3-3 3.2 memory the i+me netporty ii is equipped with flash (cs0) 128 kbyte (x 8 bit) sram (cs1) 512 kbyte (x 16 bit) optional it can be equipped with flash 512 kbyte (x 8 bit) and ram 128 kbyte (x 16 bit) 3.2.1 netporty ii internal buffers: to avoid lost data (can is fas...
Hardware protocol interface version 1.03 3-4 3.3 protocol interface the product has two can protocol chips at a frequency of 16 mhz. The sja1000 chip is connected to the 9 pin d-sub connector with the cia pinning. The optional 82527 is also connected to the 9 pin d-sub connector without physical lin...
Hardware physical interface version 1.03 3-5 3.4 physical interface netporty ii has the transceiver chip 82c251 (according to iso 11898) as physical interface. It is not galvanic disconnect. The standard physical interface is linked to the sja1000, the output control register must be set to 0xfa. To...
Hardware connector version 1.03 3-6 3.6 connector 3.6.1 9pol sub-min-d male 3.6.1.1 1 can channel the can connector is based on the cia standard if only one can channel is used. It is a 9pol sub-min-d male connector. Figure 3-1 standard can connector pins 1, 4 and 8 are not used by netporty ii.
Hardware connector version 1.03 3-7 pin signal description 1 nc not connected 2 can_l can_l bus line (dominant low) 3 can_gnd can ground (connected on the cable shield) 4 nc not connected 5 can_shield can ground (connected on the cable shield) 6 power_gnd power supply input ground 7 can_h can_h bus ...
Hardware connector version 1.03 3-8 3.6.1.2 more than 1 can channel the pinning is different if more than one can channel is used. Figure 3-2 pinning for more than 1 can channel.
Hardware connector version 1.03 3-9 pin signal description 1 uni_out2 connected to port 6.7 2 can_l can_l bus line (dominant low) 3 can_gnd can ground (connected on the cable shield) 4 uni_out0 connected to port 6.5 or uart rx or can2 rx 0 5 can_shield can ground (connected on the cable shield) 6 po...
Hardware connector version 1.03 3-10 3.6.2 25pol sub-min-d male to connect the netporty ii with the pc it is possible to use the centronics (lpt) port directly or to use the adapter cable to use the rs232 (com) port. In both cases the pinning of the 25pol sub-min-d male is the same. Connector defini...
Hardware connector version 1.03 3-11 3.6.3 cable set for serial connection cable length: 30cm 25 pin female 9 pin female signal 23 1 cd 20 2 rx 19 3 tx 16 4 dtr 18 5 gnd 24 6 dsr 21 7 rts 22 8 cts 25 9 ri.
Hardware connector version 1.03 3-12 3.6.4 power supply the netporty ii can be powered by an external power supply therefore the connector is specified for the power supply jack below: the power connector is a dc3.5/1.3 mm type. That means the internal diameter is 1.3mm. Figure 3-3 power connector f...
4 troubleshooting & techn. Support common problems and how to solve them. How to get in touch with our after-sales support experts if you so desire..
Troubleshooting & techn. Support what to do if you have problems version 1.03 4-2 4.1 what to do if you have problems first and foremost, please read installation very closely and make sure that you performed your installation exactly as described. For developers: the key is often used in developing...
Troubleshooting & techn. Support what to do if you have problems version 1.03 4-3 4.1.1 solutions for all parts ... The system crashes after choose the hardware at pccancontrol: the selected memory area is not free, or the selected interrupt is being used by another application. Make sure that no co...
Troubleshooting & techn. Support what to do if you have problems version 1.03 4-4 4.1.2 solutions for pcmcia the system crashes after the installation of the key client: the selected memory area is not free, or the selected interrupt is being used by another application. Refer to installation. The s...
Troubleshooting & techn. Support what to do if you have problems version 1.03 4-5 the key is inserted and pccancontrol starts with the message: i+me card not available or drive not ready. Some aspect of the resource allocation is wrong. Refer to installation for more information. 1.1.1 non-supported...
Troubleshooting & techn. Support what to do if you have problems version 1.03 4-6 4.1.3 solutions for netporty ii you start pccancontrol but the connection doesn’t work correct: for parallel port usage it is necessary to have the epp-loader-firmware (bootload.H86) in the netporty ii -flash-eprom. Al...
Troubleshooting & techn. Support what to do if you have problems version 1.03 4-7 the netporty ii doesn’t work under parallel port: use the right epp mode on bios. It can be only one of the epp modes work with one win-system together. In past we find out that epp 1.7 is necessary for win9x and epp 1...
Troubleshooting & techn. Support what to do if you have problems version 1.03 4-8 if you encounter difficulties which are not discussed in the manual, or if you need more help than is offered in installation and troubleshooting, please call our after-sales service. Our experts will do their best to ...
5 glossary for better understanding....
Glossary 5-2 glossary adapter a piece of hardware which contains one or more pcmcia sockets.The adapter contains the interface between the socket controller and the host system. Autoexec.Bat a set of commands in the form of a batch file program that are automatically executed by dos to help configur...
Glossary v 1.00 5-3 socket-controller a pc system hardware component that manages the operation of pcmcia sockets in conjunction with system software. System.Ini a windows initialization file (similar to the config.Sys file for dos) that contains windows device drivers, commands and settings you can...
6 literature for more informations ....
Literature 6-2 literature [1] sab 80c167cr user manual siemens ag. [2] sab c167cr description of the on-chip can-module siemens ag. [3] cia ds 102-1can in automation e.V.