I. Tech Dynamic Arrow II User Manual

Manual is about: i.Tech User Guide wireless headphone S3J-51A05053-01A

Page of 10

Download

Print this page

Bookmark us

S3J-51A05053-01A

01/2006

i.Tech Arrow II

2005 Hutchison Harbour Ring Enterprises Limited

All rights in this publication are reserved and no part may

be reproduced without the prior written permission of

the publisher. The contents of this publication are

believed to be correct at the time of going to press, but

any information, specifications, products or services

mentioned may be modified, supplemented or

withdrawn without further notice.

The Stylized i.Tech logos are trademarks owned by

Hutchison Harbour Ring Enterprises Limited or its

affiliates.

Bluetooth

and the Bluetooth logos are trademarks

owned by Bluetooth SIG, Inc, USA and licensed to i.Tech

Dynamic Limited.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired

operation.

Caution: Changes or modifications not expressly

approved by the party responsible for compliance could

void the user's authority to operate the equipment.

i.Tech declares under our sole responsibility that the

headset is in conformity with the provisions of the

following Council Directives: 1999/5/EC

User Guide

1 2 3 4 5 6 7 Next › »

Summary of Arrow II

Page 1
S3j-51a05053-01a 01/2006 i.Tech arrow ii 2005 hutchison harbour ring enterprises limited all rights in this publication are reserved and no part may be reproduced without the prior written permission of the publisher. The contents of this publication are believed to be correct at the time of going t...
Page 2
Providing a simple wireless connection to your bluetooth-enabled mobile handset, i.Tech arrow ii headset offers you the freedom to make and receive calls while on the move or at the office. The i.Tech arrow ii headset is compatible with mobile handsets that support the bluetooth headset and handsfre...
Page 3
We, i.Tech dynamic ltd., declare that the following product: product name: i.Tech arrow ii model no.: c51-a05053-xx is in conformity with the following essential requirements of council directive 1999/5/ec ( referred to as r&tte directive ) : article 3.1a, 3.1.B and 3.2. And the product is manufactu...
Page 4
15 2 i.Tech arrow ii overview (fig. 1) bluetooth specification: version 1.2 class 2 bluetooth profile supported: headset and handsfree range of frequency: 2.4ghz spectrum reception distance: 10 metres normal charging time: within 10 hours talk time*: up to 6 hours standby time*: up to 200 hours dime...
Page 5
14 3 3 charging your headset (fig. 2) the headset comes with a built-in rechargeable battery. Prior to using the headset for the first time, it is recommendable to charge the battery fully. Troubleshooting if you are unable to connect your headset and mobile handset, please try the following: • ensu...
Page 6
13 4 safety information • check local laws regarding use of a mobile handset and headset while driving. If you use the headset while driving, ensure your attention and focus remains on the road. It is your responsibility to drive safely. • never allow children to play with the headset – small parts ...
Page 7
5 12 turning on the headset press and hold the mfb (fig.1) until you hear a short beep. The status indicator will start flashing blue. Important press the mfb again each time you turn on the headset to reactivate pairing so that the connection between the headset and the mobile handset is resumed. F...
Page 8
11 6 pairing your headset prior to using your headset for the first time, you must pair it with a bluetooth-enabled mobile handset. The information on the next page describes pairing instruction for a typical bluetooth-enabled mobile handset. Headset pairing procedure is subject to different models ...
Page 9
7 10 1. Place the headset and the mobile handset where they are easily viewable and no more than 1 metre apart. 2. Ensure the headset is off. (no flashing on the status indicator). 3. Press and hold the mfb (fig. 1) until the headset status indicator alternately flashes blue and red. 4. Activate you...
Page 10
9 8 using your headset voice dialling from your headset if your mobile handset is equipped with a voice dialling function, simply press the mfb on your headset and when you hear a beep, say the voice tag. Important please make sure to record voice tags into the mobile handset first before using voic...