User manual innovative lcd display solutions ap — 10av series dp — 10av series op — 10av series u ltra v iew.
Jan 05 p.1 ap-10av / dp-10av / dp-10av series user manual 1. Table of content page.1 2. Introduction a) overview page.2 b) features page.2 c) dimension diagrams page.3-5 d) technical specifications page.6 3. Installation a) package contents page.7 b) caution to the user page.7 c) cleaning page.7 d) ...
Jan 05 p.2 disclaimer this information is subject to change without notice. The producer of this manual accepts no responsibility for damage or claims, resulting from misuse or misinterpretation a. Overview b. Features ap-10av / dp-10av / dp-10av series user manual 2. Introduction this lcd monitor i...
Jan 05 p.3 ap-10av series c. Dimension diagrams ap-10av / dp-10av / dp-10av series user manual 2. Introduction.
Jan 05 p.4 dp-10av series c. Dimension diagrams ap-10av / dp-10av / dp-10av series user manual 2. Introduction.
Jan 05 p.5 op-10av series c. Dimension diagrams ap-10av / dp-10av / dp-10av series user manual 2. Introduction.
Jan 05 p.6 technical specifications monitor panel 10.4" lcd panel display type tft lcd active matrix colour resolutions 800 x 600 response time tr=15ms, tf=25ms contrast ratio 180:1 typical brightness 350 cd/m 2 typical pixel pitch 0.264(h) x 0.264(v) panel colour 262,144 display colour viewing angl...
After unpacking the carton, check and see if the following items are included in good condition. Contact your supplier as soon as possible for replacing the missing / damaged items. ● 10.4 ” tft lcd monitor ● rca cable (optional for av version only) ● s-video cable (optional for av version only) ● v...
Jan 05 p.8 read all of these instructions and save them for later use. Follow all warnings and instructions on the product. Product ● do not cover or block the vent holes in the case. ● do not insert sharp objects or spill liquid into the lcd monitor through cabinet slots. They may cause accident fi...
Jan 05 p.9 d. Precautions (cont.) power and extension cords 1. Do not allow anything to rest on the power cord. 2. Do not locate this product where persons will walk on the cord. 3. Use the proper power cord with correct attachment plug type. If the power source is 120v ac, use a power cord that has...
A. Product views ap series - front view ap series - rear view ap-10av / dp-10av / dp-10av series user manual jan 05 p.10 3. Installation.
A. Product views (cont.) dp series - front view dp series - rear view ap-10av / dp-10av / dp-10av series user manual jan 05 p.11 3. Installation.
A. Product views (cont.) op series - front view op series - rear view ap-10av / dp-10av / dp-10av series user manual jan 05 p.12 3. Installation.
Jan 05 p.13 (2) (1) dc in : this is for connecting the power cable. (2) pc in : this can be connected with the d-sub 15 pin signal connector. (3) s-video in : this can be connected with the s-video cable connector. (for av series only) (4) rca in : this can be connected with the composite cable conn...
Jan 05 p.14 c. Installation procedures this monitor is equipped with an auto-sensing power supply for voltage ranges 100~240v, 50~60hz. Please follow the following instruction to install lcd monitor. 1. Make sure that the system power is turned off. 2. Plug the signal cable to the signal connector a...
D. Setup touchscreen touchscreen used for ultraview products are manufactured by 3m. Here provide touchware tm software includes touch screen drivers for your installing. For windows 95, 98, me, nt4.0, 2000 & xp 1. Open the driver cd provided along with the product or download the driver from our we...
D. Setup touchscreen for windows 95, 98, me, nt4.0, 2000 & xp (cont.) 7. Once installation is complete, restart the system. As the system restarts, windows detects and loads the driver. ● for serial controllers, restart the system. As the system restarts, win- dows detects and load the driver ● for ...
Jan 05 p.17 d. Setup touchscreen for dos (cont.) 7. Type install followed by the source disk drive, the destination drive, and the destination directory. For example, the following command copies the files from drive a (source drive) to drive c (destination drive) and the \mts\touch directory : inst...
D. Setup touchscreen for dos (cont.) loading the dos touchscreen driver after you install the files for the dos touchscreen driver, you must load the driver before you can run a dos touch application or open the dos touchscreen control panel. You can run the dos touchscreen driver from a full-screen...
Jan 05 p.19 e. Osd switch input select: this button is used to select cvbs for composite video input, rgb for vga input and s-video for super-video input osd menu: this button is used to enter osd main menu increase( à): this button is used to adjust the increasing or next value of selected osd cont...
F. Osd control for vga input vesion ap-10av / dp-10av / dp-10av series user manual 4. Using the system lcd membrane diagram left right exit menu/selection power main menu bright/contrast auto adjust phase/clock h/v position misc reset main menu bright / contrast ● to enter into the bright, black lev...
Jan 05 p.21 f. Osd control for vga input version ap-10av / dp-10av / dp-10av series user manual 4. Using the system bright / contrast 1. Brightness ● to perform brightness adjustment of the input rgb signal ● use the left & right button to adjust and button to “brightness” 2. Contrast ● to adjust th...
Jan 05 p.22 f. Osd control for vga input version ap-10av / dp-10av / dp-10av series user manual 4. Using the system misc 1. Information ● the first header row shows the current resolution setup ● the second header row shows the horizontal frequency of the current input signal ● the third header row ...
Jan 05 p.23 colour configuration page g. Osd control for video input version colour brightness contrast colour adjust exit brightness ︰ adjust the brightness value from 1 to 100 using ( à) and ( ß) buttons. Contrast ︰ adjust the contrast value from 1 to 100 using ( à) and ( ß) buttons. Colour adjust...
Jan 05 p.24 picture configuration page picture h.Position v.Position sharpness phase clock exit h.Position ︰ press ( à) shifting display image to right with value from 0 to 100; press ( ß) shifting display image to left from value 0 to 100. V.Position ︰ press ( à) shifting display image to upward wi...
Function configuration page function auto adjust auto position auto phase auto clock exit auto adjust ︰ enable or disable function for auto adjusting brightness, contrast, color etc. Yes ︰ enable no ︰ disable auto position ︰ enable or disable function for auto adjusting horizontal position or vertic...
Jan 05 p.26 osd menu configuration page osd menu language osd h.Position osd v.Position osd timer translucent exit language ︰ change language of osd menu for english or traditional chinese osd h.Position ︰ press ( ") shifting osd menu to right with value from 0 to 100; press ( !) shifting osd menu t...
Jan 05 p.27 miscellaneous configuration page miscellaneous mode select reset exit mode select ︰ switch the display size for 640 x 400 or 720 x 400 in dos mode reset ︰ enter for reloading all factory default exit ︰ exit the function configuration page ap-10av / dp-10av / dp-10av series user manual 4....