I3 International Am52R User Manual - User Manual
USER MANUAL
Page -2-
Am52R Analog Dome Camera
Joystick
UP
Focus Lever +
locking screw
(Far/Near)
F N
Zoom Lever +
locking screw
(Tele/Wide)
T W
UP
3-axis Range Limitations:
Pan:
0 - 355°
Tilt: 0 - 75°
Rotation:
0 - 355°
10. Connect camera to 12DC or 24AC power
and attach the service monitor to the 2-pin
connector on the camera. Make sure the
dipswitch is set to CVBS to enable Service
Monitor.
11. Adjust the lens angle by panning and tilting the
camera lens assembly and rotating the camera
lens base. Do not over-rotate the camera lens
beyond the stop point to avoid damage to the
camera.
CVBS / WDR
dipswitch
2-pin Service
Monitor
connector
13. Use the joystick on the camera board to adjust any additional camera settings (e.g.
image brightness, colour or contrast, day/night mode, etc.).
See CAMERA MENU
section for more information on camera’s on-screen menu.
14. Once the desired view is achieved, unplug the service monitor
and switch the dip switch back into WDR mode (if using).
Replace camera’s inner liner (shroud) until it snaps back into
place.
15. Replace the camera dome bubble and re-tighten 3 silver screws
securing the dome bubble to the camera base.
Joystick
FLUSH MOUNTING
Am52R camera can be flush mounted with the use of i3’s flush mounting kit
(Part # AM42FM). Sold separately. When flush-mounting the camera, do not use the
supplied camera back box.
Follow the mounting instructions supplied with the kit.
WALL MOUNTING w/ GOOSENECK BRACKET
12. Adjust the camera’s zoom and focus using
Zoom / Focus levers on the camera module.
Loosen the locking screws, adjust the lever
and re-tighten the locking screw when
desired view is achieved. Use camera’s
Smart Focus feature for best focus.
See
MENU > SETUP > SMART FOCUS section
for more information.
Am52R
Back Box
DB60
Gooseneck
Bracket
Use silicone
to maintain
IP66 rating
3/4” Rigid
Pipe
3/4” Electrical
EMT Conduit
Fitting
Use silicone
to maintain
IP66 rating
Am52R
Back Box
Am52R camera can be wall-mounted with the use
of i3’s gooseneck wall bracket (Part # DB60). Sold
separately. Together with the optional DB60CPM
bracket, DB60 gooseneck bracket has the
capability of being corner- or pole-mounted.
Follow the mounting instructions supplied
with the DB60 bracket.
Attach the top conduit hole of the camera’s
back box to the threaded end of the DB60
bracket and rotate clockwise to attach the
two together. Use silicone sealer to maintain IP66
rating when installing outdoors.
Complete installation as for Surface Mounting from Step #8 onwards.
PENDANT POLE MOUNTING
Use a 3/4” Electrical EMT Conduit Fitting with a rigid
3/4” pipe for this type of installation.
Attach the top conduit hole of the camera’s back
box to the threaded end of the 3/4” Electrical EMT
Conduit Fitting and rotate clockwise to attach the two
together.
Use silicone sealer to maintain IP66 rating
when installing outdoors.
Complete installation as for Surface Mounting
from Step #8 onwards.
CAMERA MENU
Use the camera’s on-board joystick to adjust
camera settings.
Use the button in the middle of the Joystick
to access the camera OSD MENU and confirm
selection. Move the Joystick in UP/DOWN/
LEFT/RIGHT directions to navigate within
camera menus.
UP
Press to access
camera menu
and to confirm
selection.
INSTALLING THE CAMERA
Prepare the mounting surface.
• Depending on the type of
installation, additional mounting
accessories may need to be
purchased.
• It is the installer’s responsibility
to ensure that the mounting
surface is suitable for the chosen
installation method.
• Based on installation location and
surface type, supplied screws and anchors
may not be adequate. Mounting hardware
is site-specific and may need to be supplied by the
installer.
SURFACE MOUNTING
1. Use the supplied security Torx key to loosen three
screws securing the dome bubble housing to camera
module. Gently pull the dome bubble away from the
main camera module.
2. Temporarily remove the camera liner/shroud for
easier lens adjustment.
3. Depending on the type of installation and mounting
surface, complete drilling 2-4 holes in the back box
in preparation for the mounting.
4. Attach the supplied mounting template to the
mounting surface.
5. Drill holes, as marked on the template and insert
supplied anchors into the holes. The number and
positioning of holes must match the ones pre-
drilled on the back box in Step 4.
6. Drill the conduit hole for the camera
cable, as marked on the template,
if using the top conduit hole to
route cables. Skip is using the
side conduit hole.
7. Use three tapping screws provided
to secure the camera’s back box to
the prepared mounting surface.
8. Feed the camera cables through the
selected conduit hole. Use silicone sealer
around the chosen conduit hole to maintain IP66 rating when installing outdoors.
9. Use the supplied security Torx key to attach the camera module to the back box. Use
three long machine-type screws pre-inserted into the camera module.