Ibanez B10 Instruction Manual

The output level of the instrument as well

as the quality of the signal can be affected

by the pickup height. Pickup height should

be adjusted until the volume of neck and

bridge pickups are almost equal with both

volumes wide open.  The volume may drop

drastically if the pickup height is too low.

As the pickups are magnetic, fret buzzing

and distortion may occur if the pickup is too

close to the strings. Use a small

screwdriver to make adjustments to raise

or lower the pickup.

*Instruments that have adjustable pole pieces can be adjusted to balance the output of each string.

PICKUPS

Intonation adjustment is

the operation of adjusting

the location of the string at

the saddle to compensate

for different tuning. Follow

the instructions of the

particular bridge intonation

below. Intonation is

properly set when the 12th fret note and the 12th fret harmonic are exactly the

same note. This is the center point of the scale and the most accurate way of

setting a standard scale length. With the harmonic note as the standard, if the

fretted note is flat move the bridge saddle forward toward the headstock (a) to

decrease the string length. If the fretted note is sharp, move it back away from

the headstock (b) to increase the string length intonation adjustments.

* Please note that strings can be broken when the saddle is moved, so always loosen the strings before

making adjustment.

INTONATION

ACTION

NECK

STRINGS AND TUNING MACHINES

CLEANING

IIbanez steel string models are equipped with adjustable truss rods. The purpose

of a truss rod is to adjust the neck to counteract string tension. There are many

reasons for truss rod adjustments. One of the most frequent reasons is changing

string gauges or tuning pitch which can affect string tension. String tension

changes may affect the string height and cause fret buzz or incorrect notes. To

adjust the truss rod, locate the truss rod nut and adjust it by inserting the correct

wrench into the nut and tightening (clockwise) or loosening (counter clockwise)

the rod. Truss rod tension can be measured by installing a capo at the first fret,

holding the string down at the

fret position where the neck

joins the body. Insert a thickness

gauge between the string and

the fret at the 8th fret. There

should be between 0.3 mm to

0.5 mm clearance. That

clearance is referred to as "neck

relief" Too much neck relief can

cause the neck to have higher

action in the middle of the neck

causing poor intonation and

uncomfortable playability. No

neck relief can cause fret buzz.

* Appropriate care must be taken when

adjusting the neck and we recommend only

qualified technicians perform this procedure.

Regular cleaning of your bass is

one of the most important ways

you can maintain the finish and

lengthen string life. After playing,

wipe down your instrument to

remove any perspiration from the

instrument. Perspiration can

actually contain acids that can be

corrosive to the strings and metal parts of the bass. Gloss finish basses should be

polished with polish formulated specifically for musical instruments, and a soft

treated guitar cloth or a cotton rag. Abrasive rags such as polyester can scratch

the finish. Oil finished basses should be wiped clean immediately after playing

with a dry cotton rag only. If your bass has become discolored due to extended

use or heavy perspiration, factory appearance, see a qualified bass repair person

about methods to restore the oil finish to its original factory appearance.

If strings become dirty, discolored, or

produce a dull sound or buzz, replace

the strings with new ones. For best

results we recommend replacing one

string at a time, this will help to avoid

removing the string tension from the

neck. When replacing strings with

different gauge strings, it may be

necessary to adjust the truss rod

tension. (We recommend only

qualified technicians perform this.)

Ibanez basses are factory equipped

with the following string gauges. Please follow the

instructions below for your particular model. The strings

should be tightly wound on to the tuning machines from

top to bottom with 2 to 3 string wraps around the post. In

case of tuning machines, where the string ends are

inserted into the posts, the string can be cut to length in

advance using a pair of string cutters. If the tuning

machines are sealed gear units, they are self-lubricating

types. The set screws for the tuning knob are adjustment

screws that can be tightened with a small Phillips head

screwdriver to increase the tension.

*The use of coarse strings may lead to buzzing and sound distortion. Using strings

that have twists or kinds may cause buzzing or decreased sustain. Make sure

that the strings are smooth and free from any defects before installing.

IIbanez bass string action is set at

the factory. However, there are

many reasons that an instrument's

string height can change.

Instruments can be affected by changes in temperature

and moisture. High string action can make the guitar

difficult to play. If the string action is too low, fret buzz or

unclear notes can occur. To remedy this, follow the

instructions for the particular type of bridge installed. In

the case of string action, make sure the guitar is in tune

and the truss rod is adjusted properly. Ibanez action is set

to 2.0mm for treble side and 2.5mm for bass side at the

12th fret. The action may also need to be readjusted after

the neck is adjusted or strings are changed to a different gauge. Follow the

instructions in the relevant bridge manual to make adjustments.

* If strings other than those described above are used, gradually increase the action clearance from the treble side

through to the bass side. 

INSTRUCTION MANUAL

ELECTRIC BASSES

LOOSEN

TIGHTEN

8TH FRET

0.3~0.5mm

This is to certify that the aforementioned equipments fully

conform to protection requirements of the following EC

PRINTED IN KOREA  04001NOV          © 2004

Maintenance

Our congratulations and deepest thanks on making

Ibanez your choice of instrument. Ibanez standards

are second to none. All Ibanez instruments are set up

to our strict quality control standards before shipping.

The purpose of this manual is to explain how to

maintain your instrument's finish and to keep your

guitar playing as well as it did when it left our factory.

1

3

2

LOOSEN

TIGHTEN

LOOSEN

TIGHTEN

Solid and Semi Acoustic Guitars

Full Acoustic Guitars

4 String Basses

5 String Basses

.009-.042”

.013-.054” Flat Wound

.045-.105”

.045-.105 + .130”

STRING GAUGES

LOOSEN

TIGHTEN

LOOSEN

TIGHTEN

Solid Guitars

Full Acoustic Guitars

Basses

1.5mm

1.7mm

2.0mm

2.0mm

2.3mm

2.5mm

BASS SIDE

TREBLE SIDE

The battery should be changed when the

volume becomes weak or the sound becomes

distorted. Use a new 9-volt alkaline (not

lithium or carbon) battery. The battery is

stored inside battery cavity or control cavity.

Inserting a plug into the jack activates the

power supply. Be sure to disconnect the cord

when the bass is not in use; this will prevent

the battery from draining.

BATTERY