1. DL manuals
  2. IBASE Technology
  3. Motherboard
  4. IB100
  5. User manual

IBASE Technology IB100 User manual - Checklist

Manual is about: TI AM3517 ARM CortexTM-A8 Embedded BOARD

Summary of IB100

  • Page 1

    Ib100 ti am3517 arm cortextm-a8 embedded board user’s manual version 1.0

  • Page 2: Acknowledgments

    Ii ib100 user’s manual acknowledgments ti is a registered trademark of texas instruments. All other product names or trademarks are properties of their respective owners..

  • Page 3: Introduction

    Ib100 user’s manual iii table of contents introduction ....................................................... 1 product description ............................................................. 1 checklist .............................................................................. 3 ib100 specif...

  • Page 4

    Iv ib100 user’s manual this page is intentionally left blank..

  • Page 5: Introduction

    Introduction ib100 mrs user’s manual 1 introduction product description the ib100 embedded board is based on the ti am3517 arm processor .Ti am3517 is a high-performance arm cortex-a8 with speeds up to 600 mhz. The device offers 3d graphics acceleration while also supporting numerous peripherals, in...

  • Page 6

    Introduction 2 ib100 user’s manual ib100 features: • ti am3517 600mhz arm cortex-a8 microprocessor • 256 mb ddr2 ram • 512mb nand flash • 1 x 18 bit lcd connector • 1x com port connector • 1 x mini-pcie (x1) slot (w/ usb support) • 10/100 based-t ethernet (rj-45) connector • 12v dc-in power connecto...

  • Page 7: Checklist

    Introduction ib100 mrs user’s manual 3 checklist your ib100 package should include the items listed below. •the ib100 embedded board •this user’s manual.

  • Page 8: Ib100 Specifications

    Introduction 4 ib100 user’s manual ib100 specifications mainboard ib100-mrs mpu type operating frequency ti am3517: 65nm bulk, 491-nfbga, 600mhz (arm cortextm-a8 core) 700mw tdp (est.) cache instruction cache: 16kb data cache: 16kb l2 cache: 256kb ram ddr2-667 1.8v onboard 256mb (64x16 x2) c02416040...

  • Page 9

    Introduction ib100 mrs user’s manual 5 headers & expansion slots headers: • tft lcd connector x 1 (starconn 089h40 or equivalent) • gpio x 8 (8pin, pitch 2.0 with 3.3v) • com (rs232) x 2 (pitch 2.0,com2/com3 debug port) • audio pin header x2 (mic x1 /speaker x1) • fpc connector for touch x1 (csf-059...

  • Page 10: Board Dimensions

    Introduction 6 ib100 user’s manual [ board dimensions top side.

  • Page 11

    Introduction ib100 mrs user’s manual 7 bottom side.

  • Page 12

    Installations 8 ib100 user’s manual this page is intentionally left blank..

  • Page 13: Installations

    Installations ib100 mrs user’s manual 9 installations this section provides information on how to use the jumpers and connectors on the ib100 in order to set up a workable system. The topics covered are: setting the jumpers .................................................................... 10 conn...

  • Page 14: Setting The Jumpers

    Installations 10 ib100 user’s manual setting the jumpers jumpers are used on ib100 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on ib100 and t...

  • Page 15

    Installations ib100 mrs user’s manual 11 jumper locations on ib100 top side.

  • Page 16

    Installations 12 ib100 user’s manual bottom side.

  • Page 17

    Installations ib100 mrs user’s manual 13 j13: com1 rs232 (rj45) pin8 /+5v/+3v power setting j13 setting function pin 2-4 short/closed com1 port pin 8 +5v pin 4-6 short/closed com1 port pin 8 +3v pin 8-10 short/closed com1 port pin 8 com2_tx note: pin 8 maximum output current is 0.5a default setting ...

  • Page 18

    Installations 14 ib100 user’s manual j14: cn6 id pin control (factory use only) j14 dvi signal output pin 1-2 short/closed cn6 usb used as host mode note: default is pin 1-2 open. S1 (sw1,sw2,sw3,sw4,sw5,sw6): system boot configuration s1 (sw1 .. Sw6) first second third fourth 000100 usb sd nand fla...

  • Page 19

    Installations ib100 mrs user’s manual 15 s1 (sw8): dvi signal output control s1 (sw8) function 0(off) disable dvi signal output 1(on) enable dvi signal output note: default setting is 1 (on). D8,d9,d10,d11,d12,d13,d14,d15,d16,d17,d18,d19: double colors led indicator pin # description u4. P07 low: re...

  • Page 20: Connectors On Ib100 Mrs

    Installations 16 ib100 user’s manual connectors on ib100 mrs connector locations on ib100 ............................................................ 17 cn2: sd card connector .................................................................... 18 com1 port: rj45 10 pin connector .....................

  • Page 21

    Installations ib100 mrs user’s manual 17 connector locations on ib100 b b.

  • Page 22

    Installations 18 ib100 user’s manual cn2: sd card connector com1 port: rj45 10 pin connector pin # signal name 1 com3 rxd, receive data (same signal as com3 port pin 1) 2 com1 rts, request to send 3 vdd1 4 com1 txd, transmit data 5 gnd, ground 6 gnd, ground 7 com1 rxd, receive data 8 vdd2 9 com1 cts...

  • Page 23

    Installations ib100 mrs user’s manual 19 com3 port: com3 rs232 connector, debug port connector (factory use only) pin # signal name 1 com3 rxd, receive data 2 com3 txd, transmit data 3 gnd, ground 4 nc lvds1: lvds display connector pin # signal name 1 +3.3v 2 +3.3v 3 nc 4 nc 5 tx0- 6 tx0+ 7 gnd 8 tx...

  • Page 24

    Installations 20 ib100 user’s manual cn1: lcd 18 bit parallel signal connector pin # signal name 1 +5v 2 +5v 3 backlight adj 4 gnd 5 gnd 6 +3.3v 7 +3.3v 8 mode 9 de 10 vsync 11 hsync 12 gnd 13 b5(msb) 14 b4 15 b3 16 gnd 17 b2 18 b1 19 b0 20 gnd 21 g5 22 g4 23 g3 24 gnd 25 g2 26 g1 27 g0 28 gnd 29 r5...

  • Page 25

    Installations ib100 mrs user’s manual 21 j3: lcd 24 bit parallel signal connector (factory use only) pin # signal name pin # signal name 1 +5v 23 d16 2 +5v 24 d17 3 +3.3v 25 d18 4 +3.3v 26 d19 5 d0 27 d20 6 d1 28 d21 7 d2 29 d22 8 d3 30 d23 9 d4 31 gnd 10 d5 32 de 11 d6 33 vsync 12 d7 34 hsync 13 gn...

  • Page 26

    Installations 22 ib100 user’s manual cn4: 10/100mb lan (poe supported) this rj45 lan connector supports poe function. Cn8: led backlight control connector pin # signal name 1 +12v 2 backlight adj 3 backlight enable 4 gnd note: pin 1 maximum output current is 0.5a cn9: i2c3 connector pin # signal nam...

  • Page 27

    Installations ib100 mrs user’s manual 23 cn10: spi1 connector pin # signal name 1 spi1_clk 2 spi1_simo 3 spi1_somi 4 spi1_cs0 5 +3.3v 6 gnd j2: arm jtag debug port (factory use only) j9: resistive touch connector (factory use only) j17: rs232 connector (factory use only) jmic1: mic connector pin # s...

  • Page 28

    Installations 24 ib100 user’s manual j1: digital i/o 4 in/4 out connector signal name pin # pin # signal name gnd 1 2 +3.3v out3 3 4 out1 out2 5 6 out0 in3 7 8 in1 in2 9 10 in0 note: all in/out signals level are 3.3v level. Sw1: push button for hardware reset j6: s-video connector bat1: cr2032 3v li...

  • Page 29

    Installations ib100 mrs user’s manual 25 jusb1: usb2.0 type a connector pin # signal name 1 +5v 2 d- 3 d+ 4 gnd j11: usb2.0 connector pin # signal name 1 +5v 2 d- 3 d+ 4 gnd 5 gnd j12: usb2.0 connector pin # signal name 1 +5v 2 d- 3 d+ 4 gnd 5 gnd cn6: mini usb otg connector pin # signal name 1 +5v ...

  • Page 30

    Installations 26 ib100 user’s manual j7: dvi connector pin # signal name 1 tx2+ 2 gnd 3 tx2- 4 tx1+ 5 gnd 6 tx1- 7 tx0+ 8 gnd 9 tx0- 10 txc+ 11 gnd 12 txc- 13 nc 14 nc 15 nc 16 nc 17 gnd 18 +5v 19 nc.

  • Page 31

    Installations ib100 mrs user’s manual 27 jmini1: mini pcie connector signal name pin # pin # signal name nc 1 2 +3.3v nc 3 4 gnd nc 5 6 nc nc 7 8 nc gnd 9 10 nc nc 11 12 nc nc 13 14 nc gnd 15 16 nc nc 17 18 gnd nc 19 20 nc gnd 21 22 resetn nc 23 24 nc nc 25 26 gnd gnd 27 28 nc gnd 29 30 nc nc 31 32 ...

  • Page 32

    Installations 28 ib100 user’s manual this page is intentionally left blank..

  • Page 33

    Appendix ib100 mrs user’s manual 29.