Si-313 digital signage player user’s manual version 1.0 (may 2017).
Ii si-313 user manual copyright © 2017 ibase technology, inc. All rights reserved. No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without...
Si-313 user manual iii compliance in a domestic environment, this product may cause radio interference in which case users may be required to take adequate measures. This product has been tested and found to comply with the limits for a class b device, pursuant to part 15 of the fcc rules. These lim...
Iv si-313 user manual important safety information carefully read the precautions before using the device. Environmental conditions: • lay the device horizontally on a stable and solid surface in case the device may fall, causing serious damage. • leave plenty of space around the device and do not b...
Si-313 user manual v caution danger of explosion if internal lithium-ion battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Warranty policy • ibase standard p...
Vi si-313 user manual table of contents compliance.................................................................................................... Iii important safety information ....................................................................... Iv warning ....................................
Si-313 user manual vii 2.5.6 lan port (cn5) .................................................................... 23 2.5.7 dual usb 3.0 ports (cn6) .................................................... 23 2.5.8 dual usb 2.0 ports (cn7) .................................................... 24 2.5.9 com1...
Viii si-313 user manual appendix ...................................................................................................... 52 a. I/o port address map ............................................................................ 53 b. Interrupt request lines (irq) ...........................
1 chapter 1 general information the information provided in this chapter includes: • features • packing list • specifications • optional accessories • overview • dimensions.
2 si-313 user manual 1.1 introduction si-313, a product code of ibase digital signage player series, is a mid-range system with ismart and capable of auto-scheduling for general applications. It is designed with the feature of segregated flow ventilation. The device is powered by the amd 3 rd gen. E...
General information si-313 user manual 3 1 1.3 packing list your si-313-n package should include the items listed below. If any of the items below is missing, contact the distributor or the dealer from whom you purchased the product. • si-313 digital signage player (with rack mount kit) x 1 • power ...
4 si-313 user manual 1.5 specifications product si-313 system mainboard mbd313 operating system windows 7 / 8 / 10 / linux cpu amd 3 rd gen. Embedded r-series soc apu (fp4 bga) cpu clock (max/base): 2.7ghz / 3.6 ghz chipset amd integrated soc cache up to 4 mb memory 2 x ddr4 so-dimm 4gb 2133 mhz, du...
General information si-313 user manual 5 1 i/o ports hdmi 3 x hdmi 2.0, choose either way: • use 2 ports for 4k (3840 x 2160) display at 60 hz (via hdmi 2.0) (if 3 displays are connected, the resolutions will be 4k, 4k, 1080p per the sequence of connection.) • use 3 port for 4k (3840 x 2160) display...
6 si-313 user manual 1.6 overview top view oblique view.
General information si-313 user manual 7 1 i/o view no. Name no. Name 1 dc power input 8 audio line-out 2 hdmi 2.0 port 9 microphone input 3 edid clearance button * 10 power button 4 lan port 11 led indicator for power 5 usb 3.0 12 led indicator for hdd 6 usb 2.0 13 mounting kit 7 com port 14 antenn...
8 si-313 user manual 1.7 dimensions unit: mm.
9 chapter 2 hardware installation & motherboard information the information provided in this chapter includes: • essential installations before you begin • information and locations of connectors.
10 si-313 user manual 2.1 essential installations before you begin 2.1.1 memory installation there are two so-dimm ddr4 memory slots inside si-313 for a maximum total memory of 32 gb. To install the modules, locate the memory slot on the board and perform the following steps: 1. Align the key of the...
Motherboard information si-313 user manual 11 2 2.1.2 mini pcie & m.2 network cards installation 1. Align the key of the mini pcie card to the mini pcie interface, and insert the card slantwise. (insert the m.2 network card in the same way.) 2. Push the mini pcie card down, fix it with 2 screws. (fi...
12 si-313 user manual 2.1.3 wifi / 3g / 4g antenna installation thread the wifi / 3g / 4g antenna extension cable through an antenna hole of the front i/o cover and fasten the antenna as shown below. Then apply adhesive to the edge of the hex nut behind the front i/o cover to prevent the extension c...
Motherboard information si-313 user manual 13 2 2.1.4 wall mount installation note: before mounting the system on wall, ensure that you are following all applicable building and electric codes. Requirements when mounting, ensure that you have enough room for power and signal cable routing, and have ...
14 si-313 user manual wall mount installation instructions: prepare at least 4 screws (m3) to install the device on wall as below. You can install your si-313 on plastic (lcd monitor), wood, drywall surface over studs, or a solid concrete or metal plane directly. The types of fasteners required are ...
Motherboard information si-313 user manual 15 2 2.2 setting the jumpers set up and configure your si-313 by using jumpers for various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your use. 2.2.1 how to set j...
16 si-313 user manual 2.3 jumper & connector locations on motherboard motherboard: mbd313 mbd313 - top sio j4 7 8 1 2 j2 j3 7 8 1 2 2 1 9 amd 3 rd gen. Embedded r-series soc apu l e d 5 l e d 4 s w1 c n 10 cn9 cn8 cn7 cn6 cn5 cn1 cn4 cn3 cn2 j1 1.
Motherboard information si-313 user manual 17 2 3 mbd313 - bottom j7 j12 j11 jp2 j18 j19 j14 sw2 j13 j15 j16 j17 j10 j6 j9 j8 jp1 144 1 2 143 146 145 260 259 143 2 1 144 145 145 259 260 o p e n l o c k battery 1 1 2 1 1 2 9 10 9 1 1 1 1 2 9 10 1 1 bz1.
18 si-313 user manual 2.4 jumpers quick reference jumper: function connector name page cmos data clearance jp1 18 atx / at power mode selection jp2 19 2.4.1 cmos data clearance (jp1) function pin closed illustration normal (default) 1-2 clear cmos 2-3 1 1 1.
Motherboard information si-313 user manual 19 2 2.4.2 atx / at power mode connector (jp2) function pin closed illustration atx (default) 1-2 at 2-3 1 1 1.
20 si-313 user manual 2.5 connectors quick reference i/o coastline connectors: function connector name page power button sw1 21 edid clearance button sw2 21 led indicator led4 (red, for power) led5 (green, for hdd) 22 dc power input cn1 22 hdmi 2.0 port cn2,cn3,cn4 23 lan port (gbe) cn5 23 dual usb ...
Motherboard information si-313 user manual 21 2 2.5.1 power button (sw1) 2.5.2 edid clearance button (sw2) note: be sure to press this button shortly so as to clear the edid register if any connected display/monitor is unable to be recognized, or when the image displayed cannot not be resampled to f...
22 si-313 user manual 2.5.3 led indicators for power & hdd (led4, led5) led4 led5 led4 is the red led indicator for power status. It stays on (not blinks) as the device is on. Led5 is the green led indicator for hdd. When hdd is being read, it blinks. 2.5.4 dc power input (cn1) pin assigment pin ass...
Motherboard information si-313 user manual 23 2 2.5.5 hdmi 2.0 port (cn2, cn3, cn4) 2.5.6 lan port (cn5) 2.5.7 dual usb 3.0 ports (cn6).
24 si-313 user manual 2.5.8 dual usb 2.0 ports (cn7) 2.5.9 com1 rs-232 port (cn8) pin assigment pin assigment 1 dsr (data set ready) 6 dcd (data carrier detect) 2 ground 7 dtr (data terminal ready) 3 ground 8 cts (clear to send) 4 tx (transmit) 9 rts (request to send) 5 rx (receive) 10 ri (ring indi...
Motherboard information si-313 user manual 25 2 2.5.10 audio jack (cn9, cn10) cn9: line-out cn10: microphone input 2.5.11 cpu fan power connector (j1) pin assigment 1 ground 2 +12v 3 rotation detection 1.
26 si-313 user manual 2.5.12 usb 2.0 ports header (j2) pin assigment pin assigment 1 +5v 5 data+ 2 +5v 6 data+ 3 data- 7 ground 4 data- 8 ground 2.5.13 com2 rs-232 port (j3) pin assigment pin assigment 1 dcd (data carrier detect) 6 cts (clear to send) 2 dsr (data set ready) 7 dtr (data terminal read...
Motherboard information si-313 user manual 27 2 2.5.14 system function connector (j4) pin assigment pin assigment 1 power btn 5 reset btn 2 power btn 6 reset btn 3 hdd led+ 7 +5v 4 hdd led- 8 +5vsb 2.5.15 ngff m.2 connector (j6, j13) j6 is a m.2 m-key (2280) connector with sata. J13 is a m.2 b-key (...
28 si-313 user manual 2.5.16 sim card socket (j8) 2.5.17 mini pcie connector (j10) j10 is a mini pcie connector with pci-e, usb and sim. 2.5.18 ddr4 so-dimm (j11, j12) j12 j11 s o p en l o ck.
Motherboard information si-313 user manual 29 2 2.5.19 digital i/o connector (j19) pin assigmentd pin assigment 1 ground 6 out0 2 +5v 7 in3 3 out3 8 in1 4 out1 9 in2 5 out2 10 in0 9 1 10 2.
30 chapter 3 driver installation the information provided in this chapter includes: • amd merlin falcon graphics drivers installation • hd audio driver installation • lan driver installation.
Driver installation si-313 user manual 31 3 3.1 introduction this section describes the installation procedures for software drivers. The software drivers are in a disk enclosed with the product package. If you find anything missing, please contact the distributor where you made the purchase. 3.2 am...
32 si-313 user manual 3.3 hd audio driver installation 1. Insert the disk enclosed in the package with the board. Click systemand then realtek high definition audio driver. 2. On the welcome screen of the installshield wizard, click next. 3. After reading the descriptions of the setup options, click...
Driver installation si-313 user manual 33 3 3.4 lan driver installation 1. Insert the disk enclosed in the package with the board. Click systemand then realtek gbe _fe ethernet pci-e nic driver. 2. When the welcome screen appears, click next and then install to contiune installation. 3. The driver h...
34 chapter 4 bios setup this chapter describes the different settings available in the ami bios that comes with the board. The topics covered in this chapter are as follows: • main settings • advanced settings • chipset settings • security settingss • book settings • save & exit.
Bios setup si-313 user manual 35 4 4.1 introduction the bios (basic input/output system) installed in the rom of your computer system supports intel® processors. The bios provides critical low-level support for standard devices such as disk drives, serial ports and parallel ports. It also provides p...
36 si-313 user manual 4.3 main settings bios setting description system language choose the system default language. System date sets the date. Use the key to switch between the data elements. System time set the time. Use the key to switch between the data elements..
Bios setup si-313 user manual 37 4 4.4 advanced settings this section allows you to configure, improve your system and allows you to set up some system features according to your preference..
38 si-313 user manual 4.4.1 ide configuration 4.4.2 acpi shutdown temperature.
Bios setup si-313 user manual 39 4 4.4.3 ismart controller bios setting description power-on after power failure enables / disables the system to be turned on automatically after a power failure. Schedule slot 1 / 2 sets up the hour / minute for system powe-on..
40 si-313 user manual 4.4.4 super io configuration bios setting description serial port configuration sets parameters of serial ports (coma). Enables / disables the serial port and select an optimal setting for the super io device..
Bios setup si-313 user manual 41 4 4.4.5 hardware monitor bios setting description cpu smart fan control enables / disables the smart fan feature. Disabled (default) • 50 ℃ • 60 ℃ • 70 ℃ • 80 ℃ • 90 ℃ temperatures / voltages these fields are the parameters of the hardware monitoring function feature...
42 si-313 user manual 4.4.6 cpu configuration bios setting description node 0 information shows the memory information related to node 0..
Bios setup si-313 user manual 43 4 4.4.7 sata configuration bios setting description sata controller(s) enables / disables sata devices. Sata mode selection determines how the sata controller(s) operate. • ahci mode. • raid mode. Serial ata ports enables / disables serial ports. Hot plug designates ...
44 si-313 user manual 4.4.8 csm configuration bios setting description csm support enables or disables csm support..
Bios setup si-313 user manual 45 4 4.4.9 usb configuration bios setting description legacy usb support • enable: enables ledacy usb support. • auto: disables legacy support if no usb devices are connected. • disable: keeps usb devices available only for efi applications. Xhci / ehci hand-off this is...
46 si-313 user manual 4.5 chipset settings bios setting description sourth bridge south bridge parameters north bridge north bridge parameters.
Bios setup si-313 user manual 47 4 4.5.1 south bridge 4.5.1.1. Sata configuration bios setting description sb sata / usb configuration options for sata configuration.
48 si-313 user manual 4.5.1.2. Xhci controller 4.5.2 north bridge bios setting description socket 0 information displays the information related to socket 0...
Bios setup si-313 user manual 49 4 4.6 security settings bios setting description administrator password sets an administrator password for the setup utility. User password sets a user password..
50 si-313 user manual 4.7 boot settings bios setting description setup prompt timeout number of seconds to wait for setup activation key. 65535 (0xffff) means indefinite waiting. Bootup numlock state selects the keyboard numlock state. Quiet boot enables / disables quiet boot option. Fast boot enabl...
Bios setup si-313 user manual 51 4 4.8 save & exit settings bios setting description save changes and exit exits system setup after saving the changes. Discard changes and exit exits system setup without saving any changes. Save changes and reset resets the system after saving the changes. Discard c...
52 appendix this section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. • i/o port address map • interrupt request lines (irq) • digital i/o sample code • watchdog timer configuration.
Appendix si-313 user manual 53 a. I/o port address map each peripheral device in the system is assigned a set of i/o port addresses which also becomes the identity of the device. The following table lists the i/o port addresses used. Address device description 0x00000a00-0x00000a0f motherboard resou...
54 si-313 user manual address device description 0x0000f120-0x0000f127 standard sata ahci controller 0x0000f110-0x0000f113 standard sata ahci controller 0x0000f100-0x0000f10f standard sata ahci controller 0x00000010-0x0000001f motherboard resources 0x00000022-0x0000003f motherboard resources 0x00000...
Appendix si-313 user manual 55 address device description 0x00000800-0x0000089f motherboard resources 0x00000b20-0x00000b3f motherboard resources 0x00000900-0x0000090f motherboard resources 0x00000910-0x0000091f motherboard resources 0x0000fe00-0x0000fefe motherboard resources 0x00000061-0x00000061 ...
56 si-313 user manual b. Interrupt request lines (irq) peripheral devices use interrupt request lines to notify cpu for the service required. The following table shows the irq used by the devices on board. Level function irq 0 system timer irq 0 high precision event timer irq 3 communications port (...
Appendix si-313 user manual 57 c. Watchdog timer configuration the watchdog timer (wdt) is used to generate a variety of output signals after a user programmable count. The wdt is suitable for the use in the prevention of system lock-up, such as when software becomes trapped in a deadlock. Under the...
58 si-313 user manual //--------------------------------------------------------------------------- void enablewdt(int interval) { unsigned char bbuf; bbuf = get_f81866_reg(0x2b); bbuf &= (~0x20); set_f81866_reg(0x2b, bbuf); //enable wdto set_f81866_ld(0x07); //switch to logic device 7 set_f81866_re...
Appendix si-313 user manual 59 //--------------------------------------------------------------------------- // // this code and information is provided "as is" without warranty of any // kind, either expressed or implied, including but not limited to the // implied warranties of merchantability and...
60 si-313 user manual } //--------------------------------------------------------------------------- void set_f81866_reg( unsigned char reg, unsigned char data) { unlock_f81866(); outportb(f81866_index_port, reg); outportb(f81866_data_port, data); lock_f81866(); } //--------------------------------...
