Ibm expandable storage plus 2104 model dl1 installation guide ga33-3292-00
Ibm expandable storage plus 2104 model dl1 installation guide ga33-3292-00
First edition (september 1999) the following paragraph does not apply to any country where such provisions are inconsistent with local law: this publication is printed “as is” without warranty of any kind, either express or implied, including, but not limited to, the implied warranties of merchantab...
Contents communications statements . . . . . . . . . . . . . . . . . . . V federal communications commission (fcc) statement . . . . . . . . . . V japanese voluntary control council for interference (vcci) statement. . . . . . V korean government ministry of communication (moc) statement . . . . . ....
Iv ibm expandable storage plus: 2104 model dl1 installation guide.
Communications statements the following statements apply to this product. The statements for other products intended for use with this product appear in their accompanying manuals. Federal communications commission (fcc) statement this equipment has been tested and found to comply with the limits fo...
New zealand compliance statement this is a class a product. In a domestic environment this product might cause radio interference, in which event the user might be required to take adequate measures. International electrotechnical commission (iec) statement this product has been designed and built t...
Dieses gerät ist berechtigt in Übereinstimmung mit dem deutschen emvg das eg–konformitätszeichen zu führen. Der aussteller der konformitätserklärung ist die ibm deutschland. Informationen in hinsicht emvg paragraph 3 abs. (2): das gerät erfüllt die schutzanforderungen nach en 50082-1 und en 55022 kl...
Viii ibm expandable storage plus: 2104 model dl1 installation guide.
Safety notices definitions of safety notices a danger notice indicates the presence of a hazard that has the potential of causing death or serious personal injury. This book contains no danger notices. A caution notice indicates the presence of a hazard that has the potential of causing moderate or ...
X ibm expandable storage plus: 2104 model dl1 installation guide.
About this book this book provides installation instructions for any person who is required to install a 2104 model dl1, which is a rack-mounted small computer systems interface (scsi) disk enclosure. Numbering convention in this book, one gigabyte (gb) equals 1 000 000 000 bytes. Related publicatio...
Xii ibm expandable storage plus: 2104 model dl1 installation guide.
Installing a 2104 model dl1 important: the installation of this product is a customer responsibility. Attention: before continuing with any of the actions described in this book, please read the safety notices now. These are in “appendix b. Translated safety notices” on page 31. Attention: when you ...
If the 2104 disk enclosure has already been installed in the rack: v go to “connecting the 2104 model dl1 to the power source” on page 21 if the power cables for the 2104 have not been installed. V go to “connecting the 2104 to the using system” on page 23 if the power cables for the 2104 have been ...
Installing a 2104 model dl1 into an rs/6000 rack installing a 2104 model dl1 into an rs/6000 rack is done by: 1. Preparing the rs/6000 rack 2. Removing the disk drive modules from the 2104 model dl1 3. Installing the 2104 model dl1 into the rack 4. Reinstalling the disk drive modules into the 2104 m...
Checking the items for an rs/6000 rack 1. Refer to figure 1. 1 2104 model dl1 5 support rails 2 mounting screws (front) 6 mounting screws (back) 3 rail mounting screws 7 power cable(s) 4 nut clips note: if your 2104 model dl1 has only one fan-and-power-supply assembly, only one power cable is suppli...
Preparing the rs/6000 rack (system or expansion) notes: 1. If you are installing the 2104 disk enclosure into an empty rack, install it into the lowest available position so that the rack does not become unstable. 2. If you are installing more than one 2104 disk enclosure into the rack, start at the...
4. Refer to figure 2. 5. For each support rail: a. Attach nut clips 1 and 2 at the selected holes in the rack. The selected holes should be at the same positions at the front and back of the rack. B. Loosen the five screws 4 and 5 on the support rail so that the support rail can be extended to fit t...
Leave the rail screw 5 loose; it will be tightened later. 6. Go to “removing the disk drive modules and dummy disk drive modules” on page 8. Installing a 2104 model dl1 7.
Removing the disk drive modules and dummy disk drive modules caution: a fully-configured 2104 model dl1 weighs up to 38.5 kg (85 lb) with disk drive modules installed. Do not attempt to lift the 2104 disk enclosure into the rack unless all the disk drive modules have been removed. Attention: disk dr...
3. Refer to figure 4. 4. Press the blue latch 1, and pull the handle 2 fully up. This action pulls the disk drive module partially out of its slot. 1 2 figure 4. Opening the handle of a disk drive module installing a 2104 model dl1 9.
5. Refer to figure 5. 6. Grip the handle, and carefully pull out the disk drive module. As the module comes out, put one hand under its base to prevent it from falling. Figure 5. Removing a disk drive module 10 ibm expandable storage plus: 2104 model dl1 installation guide.
7. Lay the disk drive module on its side as shown in figure 6. It rests on four blue supports (not visible in the figure) on the bottom of the disk drive module. This prevents the disk drive module from falling over and becoming damaged. Note: it is recommended that the removed disk drive modules be...
9. You may also wish to remove the dummy disk drive modules. A dummy disk drive module has a simple handle. There is no latch to be pulled upward. Refer to figure 7. Figure 7. Removing a dummy disk drive module 12 ibm expandable storage plus: 2104 model dl1 installation guide.
Installing the 2104 model dl1 into an rs/6000 rack caution: the stabilizer must be correctly attached to the bottom front of the rack to prevent the rack from tipping forward while the 2104 disk enclosure is being installed into the rack. Do not install or pull out any unit if the stabilizer is not ...
3. Refer to figure 8. 4. Install the two front mounting screws 1 and tighten them. 1 1 figure 8. Installing the front mounting screws 14 ibm expandable storage plus: 2104 model dl1 installation guide.
5. Refer to figure 9. 6. At the back of the rack, install and tighten the two screws 1. Note: these are the screws identified as 5 in figure 2 on page 6. 7. Go to “reinstalling the disk drive modules and dummy disk drive modules” on page 16. 1 1 figure 9. Installing the back mounting screws installi...
Reinstalling the disk drive modules and dummy disk drive modules attention: v disk drive modules are fragile. Handle them with care, and keep them well away from strong magnetic fields. V any slot that has no disk drive module installed must contain a dummy disk drive module. The dummy disk drive mo...
5. Refer to figure 11. 6. While continuing to push the disk drive module into the slot, slowly close the handle 1 until it stops with a click. This action pushes the module fully home. 7. Verify that the disk drive module that you have just installed is aligned with the sides of the 2104 and that no...
9. Ensure that the 2104 disk enclosure has no empty slots. Install dummy disk drive modules if necessary. 10. Refer to figure 12. 11. Go to “connecting the 2104 model dl1 to the power source” on page 21. Figure 12. Reinstalling a dummy disk drive module 18 ibm expandable storage plus: 2104 model dl1...
Getting ready to connect the 2104 model dl1 1. Referring to your preinstallation planning information, check how the 2104 is to be connected to the using system. 2. Refer to figure 13. 3. Rotate the box id rotary switch to the id you have chosen for this 2104 disk enclosure. You need a small screwdr...
5. Now look at the option switches. Refer to figure 14. 6. Switch 1, the power control switch, if set on, means that this 2104 model dl1 does not automatically switch on or off when the host machine is switched on or off. If you want this 2104 model dl1 to switch on automatically when the host machi...
Connecting the 2104 model dl1 to the power source 1. Refer to figure 15. 2. At the back of the 2104, plug a power cable into the mainline power connector 1 on each fan-and-power-supply assembly. Attention: never use power cables from another drawer to connect a 2104 to the mainline power outlet. Use...
3. Refer to figure 16. 4. Ensure that the dc on/standby switch 1 is set to standby. 5. Ensure that all power is removed from the rack. 6. Plug the other end of the power cable into the power source in the rack (see the installation and service guide, or equivalent, for the rack). 7. Perform the grou...
Connecting the 2104 to the using system 1. Referring to your preinstallation planning information, check how the 2104 is to be connected to the using system. 1. Attach identification labels to the external scsi signal cables (see the appropriate adapters, devices and cables information manual for de...
Figure 18. Back of fully configured 2104 model dl1 after connection to the using system 24 ibm expandable storage plus: 2104 model dl1 installation guide.
Switching on and testing the 2104 1. If the power to the using system is switched off, switch it on. 2. Refer to figure 19. 3. The 2104 disk enclosure has two lights. The green 2104 activity light 1 comes on and stays on. The amber 2104 check light 2 comes on for approximately two seconds and goes o...
If the lights are correct, go to “appendix a. Operating with risc systems” on page 27 which gives information about how to configure your 2104 to the using system, what service aids are available, and how to collect statistics during the operation of your 2104. If the 2104 check light 2 is on, there...
Appendix a. Operating with risc systems this appendix gives advice when operating risc systems to which ibm expandable storage plus disk enclosures are attached. Scsi service aids service aids are available on the using system to help you service the ibm expandable storage plus disk enclosure. Servi...
The cron requires a script. To create this script, generate a file named run_ses_healthcheck in directory /usr/lpp/diagnostics/bin. The contents of the file must be: #!/bin/ksh #name: run_ses_healthcheck #location: /usr/lpp/diagnostics/bin #function: scsi ses hourly healthcheck /usr/sbin/lsdev -cc c...
V adapters, devices and cable information for multiple bus systems, sa38-0516 appendix a. Operating with risc systems 29.
30 ibm expandable storage plus: 2104 model dl1 installation guide.
Appendix b. Translated safety notices this appendix contains the danger and caution notices that are used in the various books related to the expandable storage plus: 2104 models dl1 and tl1. The notices are shown in english and in various other languages. Danger notice a danger notice calls attenti...
Caution notices caution: this unit may have two linecords, to remove all power, disconnect both linecords. Caution: this unit weighs 38.5 kg. Caution: the stabilizer must be correctly attached to the bottom front of the rack to prevent the rack from tipping forward while the units are being removed ...
Cette annexe contient la traduction des consignes de type danger et attention figurant dans les diff rents manuels concernant expandable storage plus: 2104 models dl1 and tl1. é consignes de type danger les consignes de s curit de type danger indiquent la pr sence d'un risque de blessures graves, vo...
Consignes attention attention: le stabilisateur doit tre solidement fix au bas de la face avant de l'armoire pour emp cher cette derni re de basculer lorsqu'on en retire des unit s. Ne retirez pas ou n'installez pas d'unit avant d'avoir v rifi que le stabilisateur est bien fix l'armoire. ê é ê è é é...
Dieser abschnitt enth lt die sicherheitshinweise vorsicht und achtung, die in den ver ffentlichungen zum ibm expandable storage plus 2104, modelle dl1 und tl1 verwendet werden. ä ö hinweis vorsicht der hinweis vorsicht macht auf eine gefahr aufmerksam, die t dliche oder schwere verletzungen zur folg...
Hinweise achtung achtung: der stabilisator muß ordnungsgemäß unten an der vorderseite des gehäuses angebracht werden, um ein vorkippen beim entfernen der einheiten aus dem gehäuse zu verhindern. Die einheiten nicht installieren oder entfernen, wenn der stabilisator nicht am gehäuse montiert ist. Ach...
Greek appendix b. Translated safety notices 37.
Dc sw1 caution: double pole / neutral fusing f2 = t10a / 250v f1 = t10a / 250v l n 38 ibm expandable storage plus: 2104 model dl1 installation guide.
Appendix b. Translated safety notices 39.
40 ibm expandable storage plus: 2104 model dl1 installation guide.
Appendix b. Translated safety notices 41.
Dc sw1 caution: double pole / neutral fusing f2 = t10a / 250v f1 = t10a / 250v l n 38.5 38.5 85 42 ibm expandable storage plus: 2104 model dl1 installation guide.
Questo opuscolo contiene la traduzione degli avvisi di pericolo e di attenzione presenti nei manuali relativi all'expandable storage plus: 2104 modelli dl1 e tl1. Avviso di pericolo un avviso di pericolo richiama l'attenzione su una situazione potenzialmente mortale oppure estremamente pericolosa pe...
Avvisi di attenzione attenzione: lo stabilizzatore deve essere correttamente assicurato alla parte frontale, estremit inferiore del rack per evitare che quest'ultimo si inclini in avanti durante la rimozione delle unit dal rack. Non installare o non estrarre alcuna unit se lo stabilizzatore non inst...
Appendix b. Translated safety notices 45.
46 ibm expandable storage plus: 2104 model dl1 installation guide.
Appendix b. Translated safety notices 47.
Dc sw1 caution: double pole / neutral fusing f2 = t10a / 250v f1 = t10a / 250v l n 38.5 48 ibm expandable storage plus: 2104 model dl1 installation guide.
Este apêndice contém traduções dos avisos de perigo e cuidado utilizados em diversos manuais relacionados ao produto expandable storage plus: 2104 modelos dl1 e tl1. Aviso de perigo um aviso de perigo adverte sobre uma situação potencialmente letal ou extremamente prejudicial às pessoas. Aviso de cu...
Avisos de cuidado cuidado: o estabilizador deve estar conectado corretamente à parte frontal inferior do rack para evitar que o rack caia para frente quando as unidades estiverem sendo removidas do rack. Não retire ou instale nenhuma unidade, se o estabilizador não estiver conectado ao rack. Cuidado...
Appendix b. Translated safety notices 51.
Dc sw1 caution: double pole / neutral fusing f2 = t10a / 250v f1 = t10a / 250v l n 52 ibm expandable storage plus: 2104 model dl1 installation guide.
Part number: 09l3321 printed in the u.S.A. Ga33-3292-00 09l3321.