Technical information manual pc 300pl types 6862 and 6892 pc 300gl types 6275 and 6285.
Ibm technical information manual pc 300pl types 6862 and 6892 pc 300gl types 6275 and 6285.
Note before using this information and the product it supports, be sure to read the general information under appendix e, “notices and trademarks” on page 70. Preliminary edition (june 1998) the following paragraph does not apply to the united kingdom or any country where such provisions are inconsi...
Contents preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Viii related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ix terminology usage . . . . . . . . . . . . . . . ...
Tower model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 scsi adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 cabling requirements for wake on lan adapters . . . . . . . . . . ....
Software compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 software interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 machine-sensitive programs . . . . . . . . . . . . . . . . . . ...
Figures 1. Memory configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2. Serial port assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3. Parallel port assignments . . . . . . . . . . . . . . . . . . ...
51. Irq channel assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 52. Dma channel assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 figures vii.
Preface this technical information manual provides information for the ibm pc 300pl (types 6862 and 6892) and pc 300gl (types 6275 and 6285). It is intended for developers who want to provide hardware and software products to operate with these ibm computers and provides an in-depth view of how thes...
Related publications in addition to this manual, the following ibm publications provide information related to the operation of the ibm pc 300pl (types 6862 and 6892) and pc 300gl (types 6275 and 6285). To order publications in the u.S. And puerto rico, call 1-800-879-2755. In other countries, conta...
Terminology usage attention! The term reserved describes certain signals, bits, and registers that should not be changed. Use of reserved areas can cause compatibility problems, loss of data, or permanent damage to the hardware. When the contents of a register are changed, the state of the reserved ...
Chapter 1. System overview chapter 1. System overview pc 300pl (types 6862 and 6892) and pc 300gl (types 6275 and 6285) are versatile products designed to provide state-of-the-art computing power with room for future growth. Types 6275 and 6862 are desktop models, and types 6285 and 6892 are tower m...
Chapter 1. System overview audio adapter (supports soundblaster, adlib, and microsoft windows sound system applications) is optional in pc 300gl (types 6275 and 6285) integrated 16-bit, stereo audio controller and built-in high quality speaker in pc 300pl (types 6862 and 6892) (supports soundblaster...
Chapter 1. System overview other features the following features may be supported by the pc 300gl (types 6275 and 6285) and pc 300pl (types 6862 and 6892). Wake on lan the power supply of the computer supports the wake on lan feature. With the wake on lan feature, the computer can be turned on when ...
Chapter 2. System-board features chapter 2. System board features this section includes information about system-board features. For an illustration of the system board, see “system board, types 6862/6892 and 6275/6285” on page 14. Microprocessor pc 300gl (types 6275 and 6285) and pc 300pl (types 68...
Chapter 2. System-board features l2 cache pc 300pl and pc 300gl computers are all equipped with a pentium ii microprocessor with mmx technology and 512 kb of l2 cache. The l2 cache ecc function is automatically enabled when ecc memory is installed. If nonparity memory is installed, the l2 cache ecc ...
Chapter 2. System-board features figure 1. Memory configurations total memory (mb) mem 0 mem 1 mem2 16 16 0 0 32 16 16 0 32 32 0 0 48 16 16 16 48 32 16 0 64 32 16 16 64 32 32 0 64 64 0 0 96 32 32 32 96 64 32 0 128 64 32 32 128 64 64 0 128 128 0 0 160 32 64 64 192 64 64 64 224 32 64 128 256 128 64 64...
Chapter 2. System-board features the ide devices receive their power through a four-position power cable containing +5, +12, and ground voltage. When adding devices to the ide interface, one device is designated as the master device and another is designated as the slave or subordinate device. These...
Chapter 2. System-board features video subsystem the video subsystem on the system board includes the integrated agp s3 trio 3d svga (super video graphics array) controller. The system board supports up to two sgram memory modules. Each module contains 2 mb of sgram memory. Integrated agp s3 trio 3d...
Chapter 2. System-board features audio subsystem all pc 300pl (types 6862 and 6892) models come with integrated audio. Some pc 300gl (types 6275 and 6285) models come with a crystal audio adapter. These models, which are capable of playing and recording sounds, support soundblaster, adlib, and micro...
Chapter 2. System-board features input/output controller control of the integrated input/output (i/o) and diskette drive controllers is provided by a single module, the smc 37c673. This module, which supports plug and play, controls the following features: diskette drive interface serial port parall...
Chapter 2. System-board features parallel port integrated in the system board is support for extended capabilities port (ecp), enhanced parallel port (epp), and standard parallel port (spp) modes. The modes of operation are selected through the configuration/setup utility program with the default mo...
Chapter 2. System-board features viewable mac address provided pci 2.1 compliant bus master features of the optional token-ring adapter are: transmits and receives data at 4 mbps or 16 mbps rj-45 and d-shell connectors for lan attachment wake on lan support rpl or dhcp support pc 300gl (types 6275 a...
Chapter 2. System-board features flash eeprom the system board uses an 8 mb flash electrically-erasable, programmable, read-only memory (eeprom) to store the basic input/output system (bios), video bios, ibm logo, configuration/setup utility, and plug and play data. If necessary, the eeprom can be e...
Chapter 2. System-board features physical layout the system board might look slightly different from the one shown. Note: a diagram of the system board, including switch and jumper settings, is attached to the underside of the computer cover. System board, types 6862/6892 and 6275/6285 1 battery 2 m...
Chapter 2. System-board features switch 5 is rom recovery. Switch 6 enables or disables the system board ethernet. When the ethernet disable switch is on, the system board ethernet is disabled. This switch must be on when a wake on lan adapter is installed. (note that only one wake on lan device can...
Chapter 2. System-board features switch 8 controls writes to the diskette drive. Jumper jumpers on the system board are used for custom configurations. For the location of the clear cmos request jumper, refer to the “system board, types 6862/6892 and 6275/6285” on page 14, above.. Riser card, type 6...
Chapter 2. System-board features riser card, type 6275/6862 the riser card in your computer has two isa slots and three pci slots. The third pci connector from the top shares a slot with the isa connector directly below it. The other slots are dedicated to either the isa or pci bus. You can install ...
Chapter 2. System-board features connector panel, types 6275/6862 connectors for features that are integrated into the system board can be identified by a symbol directly below the connector. Connectors provided by an adapter might not have an identifying symbol. For pinout details on connectors, se...
Chapter 2. System-board features note: models equipped with a scsi adapter have an external connector for connecting scsi devices. See the scsi documentation provided with your computer for more information. Chapter 2. System board features 19.
Chapter 3. Physical specifications chapter 3. Physical specifications this section lists the physical specifications for the pc 300gl (types 6275 and 6285) and pc 300pl (types 6862 and 6892).. The pc 300 types 6275/6862 has four expansion slots and four drive bays, and the pc 300 types 6285/6892 has...
Chapter 3. Physical specifications system specifications system specifications are provided to assist you with the setup of your computer. Desktop model dimensions height: 128 mm (5.0 in.) width: 450 mm (17.7 in.) depth: 450 mm (17.7 in.) weight minimum configuration as shipped: 9.9 kg (22 lb) maxim...
Chapter 3. Physical specifications tower model dimensions height: 492 mm (19.4 in.) width: 200 mm (7.9 in.) depth: 445 mm (17.5 in.) weight minimum configuration as shipped: 15 kg (33 lb) maximum configuration: 17.3 kg (38 lb) environment air temperature: – system on: 10° to 32°c (50° to 90°f) – sys...
Chapter 3. Physical specifications cabling requirements for wake on lan adapters wake on lan adapters have two headers: a 3-pin, right-angle header for providing aux5 (auxiliary 5 volts), and a 2-pin straight header for connecting the wakeup signal to the system board (or riser card). The pc 300gl a...
Chapter 4. Power supply chapter 4. Power supply the power supply requirements are supplied by 145-watt pc 300 types 6275/6862 (desktop models) or 200-watt pc 300 types 6285/6892 (tower models) power supply. The power supply provides 3.3-volt power for the pentium microprocessor and core chip set and...
Chapter 4. Power supply pc 300gl type 6285 and pc 300pl type 6892 the total combined 3.3 v/5 v power should not exceed 120 watts. Figure 13. Power output (200 watt) output voltage regulation minimum current maximum current +5 volts +5% to − 4% 1.5 a 20.0 a +12 volts +5% to − 5% 0.2 a 8.0 a − 12 volt...
Chapter 4. Power supply component outputs the power supply provides separate voltage sources for the system board and internal storage devices. The following figures show the approximate power that is provided for specific system components. Many components draw less current than the maximum shown. ...
Chapter 4. Power supply note: some adapters and hard disk drives draw more current than the recommended limits. These adapters and drives can be installed in the system; however, the power supply will shut down if the total power used exceeds the maximum power that is available. Output protection th...
Chapter 5. System software chapter 5. System software this section briefly describes some of the system software included with the computer. Bios the computer uses the ibm basic input/output system (bios), which is stored in flash electrically erasable programmable read only memory (eeprom). Some fe...
Chapter 5. System software configuration/setup utility program the configuration/setup utility program provides menus for selecting options for devices, i/o ports, date and time, system security, start options, advanced setup, isa legacy resources, and power management. More information on using the...
Chapter 6. Ibm system management tools chapter 6. Ibm system management tools ibm system management tools are a collection of hardware and software features designed to make it easier to manage your system over a computer network. When used in conjunction with the appropriate network management soft...
Chapter 6. Ibm system management tools ibm pc system monitor (lm80) this application monitors system-board temperatures, system voltages, and fan speed, and detects removal of the computer cover. Data is reported to the dmi service provider. System management software, such as ibm netfinity services...
Chapter 6. Ibm system management tools power management controller piix4e contains support for advanced power management features, including clock control, and various low-power state control logic. In combination with the onboard battery backed rtc logic, the piix4e provides full hardware and softw...
Chapter 6. Ibm system management tools data can be written and read through either the rf interface to the system or the smbus. Writing and reading via the rf interface requires a portable hand held reader or door reader. Software residing in the hand held reader and portal gate controller are requi...
Chapter 6. Ibm system management tools figure 22 (page 1 of 2). Device types device type device number device number dynamic update comment 0 0-7 null no device not included in rfid eeprom 1 0-7 cpu no 2 0-7 reserved do not use 3 0-7 other ide devices no includes ide devices that do not support elec...
Chapter 6. Ibm system management tools the two checksums for the serialization area are included in the area header. The checksum for the header is used to check the data contained in the first 7 bytes (0-6) of the header. The checksum for the area is used to check the data located in all of the are...
Chapter 6. Ibm system management tools system configuration information includes processor type and speed, hard drive size, and memory configuration as well as information about on-board devices. Both the serial number and system configuration information can be retrieved by system management applic...
Chapter 6. Ibm system management tools security, or to whomever you designate. When paired with an ibm netfinity server or intel landesk server products, alert on lan can send a message to your pager. Alert on lan sends either status or alert packets to your management server. Even after the system ...
Chapter 6. Ibm system management tools ibm smart reaction client has a full-function backup and restoration program, as well as a mirroring program, which can be used to dynamically "mirror" the contents of up to 64 folders to another hard disk. As source files are saved, the mirror files are automa...
Chapter 6. Ibm system management tools ibm smart reaction ibm smart reaction adds an important new tool to ibm's comprehensive suite of asset protection solutions, which provide customers with system security and data protection capabilities that help protect technology and information assets. These...
Chapter 6. Ibm system management tools includes information such as drive size, partitioning, file format and current capacity. This enables smart reaction manager to allocate the necessary space on the administrator-defined backup file server. Once the space is allocated, smart reaction client tran...
Chapter 6. Ibm system management tools intel landesk client manager the landesk client manager is a dmi compliant management application that supplies a user-friendly dmi management interface and component instrumentation. This application provides self-help tools, including a pc health meter, local...
Chapter 6. Ibm system management tools pcs in your network so that lccm, ibm netfinity manager or landesk can perform the management tasks you've defined. Wake on lan components wake on lan requires the following components: a wake on lan-enabled token-ring or ethernet lan adapter card these adapter...
Chapter 6. Ibm system management tools pattern of 16 addresses in the data field is not expected to occur in any normal lan frame other than the specific wake-up frame. The destination address can be either a specific address or a broadcast address. If the destination address is a specific address, ...
Chapter 6. Ibm system management tools handheld asset id unit. Prompt users (if present) for specific information about their name, department, location, etc. And capture this information into the client hardware information. Export captured client information to other tools for inclusion in higher ...
Chapter 6. Ibm system management tools one or more pcs over the network. The magic packet identifies each specific pc through the unique mac address assigned to every network interface device. Lccm can broadcast a magic packet on local area networks made up of hubs, bridges, and switches. Lccm can a...
Chapter 6. Ibm system management tools lccm new client scenario 1. Lccm administrator starts scanning the network for new pcs 2. 2 pcs found. Lccm displays pc serial #, captures and associates vital product data, etc. 3. Lccm creates individual client details notebook for new clients 4. Administrato...
Chapter 6. Ibm system management tools lccm can save customers and ibm remarketers significant costs by reducing the time and personnel required to deploy and manage pcs. Lccm is a key component in the ibm strategy to help customers regain control over their technology so they can better manage thei...
Chapter 7. System compatibility chapter 7. System compatibility this chapter discusses some of the hardware, software, and bios compatibility issues for the computer. Refer to &comp. For a list of compatible hardware and software options. Hardware compatibility this section discusses hardware, softw...
Chapter 7. System compatibility hardware interrupts hardware interrupts are level sensitive for pci interrupts and edge sensitive for isa interrupts. The interrupt controller clears its in-service register bit when the interrupt routine sends an end-of-interrupt (eoi) command to the controller. The ...
Chapter 7. System compatibility diskette drives and controller the following figures show the reading, writing, and formatting capabilities of each type of diskette drive. Notes: 1. Do not use either a 250/500 kb or 300/500 kb diskette drive for 5.25-inch diskettes that are designed for the 1.2mb mo...
Chapter 7. System compatibility hard disk drives and controller reading from and writing to the hard disk is initiated in the same way as in ibm personal computer products; however, new functions are supported. Software compatibility to maintain software compatibility, the interrupt polling mechanis...
Appendix a. Connector pin assignments appendix a. Connector pin assignments the following figures show the pin assignments for various system board connectors. Agp monitor port connector 5 1 10 6 15 11 memory connectors 1 85 84 168 figure 28. Agp monitor port connector pin assignments pin signal i/o...
Appendix a. Connector pin assignments figure 29 (page 2 of 3). System memory connector pin assignments pin x64 non-parity x72 ecc pin x64 non-parity x72 ecc 13 dq9 dq9 97 dq41 dq41 14 dq10 dq10 98 dq42 dq42 15 dq11 dq11 99 dq43 dq43 16 dq12 dq12 100 dq44 dq44 17 dq13 dq13 101 dq45 dq45 18 vcc vcc 10...
Appendix a. Connector pin assignments isa connectors a1 b1 a31 b31 c1 d1 c18 d18 note: the isa connectors are on the riser card. Figure 29 (page 3 of 3). System memory connector pin assignments pin x64 non-parity x72 ecc pin x64 non-parity x72 ecc 56 dq17 dq17 140 dq49 dq49 57 dq18 dq18 141 dq50 dq5...
Appendix a. Connector pin assignments figure 30 (page 2 of 3). Isa connector pin assignments pin signal i/o pin signal i/o b3 +5 v dc na a3 sd6 i/o b4 irq2 i a4 sd5 i/o b5 -5 v dc na a5 sd4 i/o b6 drq2 i a6 sd3 i/o b7 -12 v dc na a7 sd2 i/o b8 ows# i a8 sd1 i/o b9 +12 v dc na a9 sd0 i/o b10 ground n...
Appendix a. Connector pin assignments pci connectors b2 a1 a2 b62 a62 b1 figure 31. Pci bus connector note: the pci connectors are on the riser card. Figure 30 (page 3 of 3). Isa connector pin assignments pin signal i/o pin signal i/o d15 drq7 i c15 sd12 i/o d16 +5 v dc na c16 sd13 i/o d17 master# i...
Appendix a. Connector pin assignments figure 32 (page 2 of 2). Pci connector pin assignments pin signal i/o pin signal i/o a26 idsel o b26 c/be 3# i/o a27 + 3.3 v dc na b27 address/data 23 i/o a28 address/data 22 i/o b28 ground na a29 address/data 20 i/o b29 address/data 21 i/o a30 ground i/o b30 ad...
Appendix a. Connector pin assignments ide connectors 1 2 40 39 note: the ide connectors are on the riser card. Diskette drive connector note: the diskette drive connector is on the riser card. Figure 33. Ide connector pin assignments pin signal i/o pin signal i/o 1 nc o 21 nc na 2 ground na 22 groun...
Appendix a. Connector pin assignments power supply connector note: the power supply connector is on the riser card. Modem/ring wakeup and wake on lan connectors note: the modem/ring wakeup and wake on lan connectors are on the riser card. Figure 34 (page 2 of 2). Diskette drive connector pin assignm...
Appendix a. Connector pin assignments alert on lan connector rfid connector (asset id) fan connector the lm80 system management chip thermally controls the front fan. If the termperature of the system is lower than the programmed threshold, then the fan will be turned off. The lm80 and the system ma...
Appendix a. Connector pin assignments mouse and keyboard port connectors 6 4 2 1 3 5 serial port connectors 1 5 6 9 parallel port connector 13 1 25 14 figure 42. Mouse and keyboard port connector pin assignments pin signal i/o pin signal i/o 1 data i/o 2 reserved na 3 ground na 4 +5 v dc na 5 clock ...
Appendix a. Connector pin assignments figure 44 (page 2 of 2). Parallel port connector pin assignments pin signal i/o pin signal i/o 17 slct in# o 18 ground na 19 ground na 20 ground na 21 ground na 22 ground na 23 ground na 24 ground na 25 ground na 62 technical information manual.
Appendix a. Connector pin assignments monitor port connector 5 1 10 6 15 11 ethernet connector 2 1 8 7 figure 46. Ethernet connector the external interface for the ethernet port is an 8-pin, rj-45 connector. Figure 45. Monitor connector pin assignments pin signal i/o pin signal i/o 1 red o 2 green o...
Appendix b. System address maps appendix b. System address maps system memory map the first 640 kb of system board ram is mapped starting at address hex 0000000. A 256-byte area and a 1 kb area of this ram are reserved for bios data areas. Memory can be mapped differently if post detects an error. I...
Appendix b. System address maps figure 49 (page 2 of 3). I/o address map address (hex) size description 00c0–00de 31 bytes dma 2 00f0 1 byte reset numeric error 0170–0177 8 bytes secondary ide channel 01f0–01f7 8 bytes primary ide channel 0200–0207 8 bytes available 0220–022f 16 bytes available 0240...
Appendix b. System address maps dma i/o address map the following figure lists resource assignments for the dma address map. Any addresses that are not shown are reserved. Figure 49 (page 3 of 3). I/o address map address (hex) size description 0f40–0f47 8 bytes windows sound system (if present) 0f86...
Appendix b. System address maps pci configuration space map figure 50 (page 2 of 2). Dma i/o address map address (hex) description bits byte pointer 00c8 channel 6, memory address register 00–15 yes 00ca channel 6, transfer count register 00–15 yes 00cc channel 7, memory address register 00–15 yes 0...
Appendix c. Irq and dma channel assignments appendix c. Irq and dma channel assignments the following figures list the interrupt request (irq) and direct memory access (dma) channel assignments. Figure 51. Irq channel assignments irq system resource nmi i/o channel check 0 reserved (interval timer) ...
Appendix d. Error codes appendix d. Error codes a complete list of post error codes is provided in using your personal computer. Post error codes post error messages appear when post finds problems with the hardware during power-on or when a change in the hardware configuration is found. Post error ...
Appendix e. Notices and trademarks appendix e. Notices and trademarks references in this publication to ibm products, programs, or services do not imply that ibm intends to make these available in all countries in which ibm operates. Any reference to an ibm product, program, or service is not intend...
References 82439hx pciset system controller (txc) source: intel corporation; available at http://www.Intel.Com/design/pcisets/datashts 82371sb pci isa ide xcelerator (piix3) source: intel corporation; available at http://www.Intel.Com/design/pcisets/datashts advanced power management (apm) bios inte...
Index index a address map dma 66 i/o 64 system memory 64 advanced power management 29 alert on lan 3 apm 29 asset id 3 audio 9 b beep codes 69 bios 28 bios data areas 64 bus ide 6 isa 7, 13 pci 6, 13 universal serial bus 7 bypassing bios 50 c chip set 4, 10 clock, real-time 12 cmos ram 12 compatibil...
Index input power (continued) requirements 24 voltage 24 interrupt request assignments 68 isa bus 7 connectors 13 j jumper configuration 16 locations (system board) 14 l l2 cache 5 level-sensitive interrupts 49 load currents 26 m machine-sensitive programs 51 memory error in 64 map, system 64 ram 64...
Index v video subsystem 8 voltage, input power 24 voltage, output power 24 w wake on lan 3 wake up on ring 3 write current, diskette 50 write-protect switch, diskette drive 16 74 technical information manual.
Ibm part number: xxxxxxx printed in u.S.A. Xxxxxxx.
