1. DL manuals
  2. IBM
  3. Motherboard
  4. NuPRO-630
  5. Manual

IBM NuPRO-630 Manual

Manual is about: Pentium-II Bus-100MHz VGA, Full Size All-in-one PC/104 VGA CRT Interface, Supports DMA33 WDT DOC USB IrDA, PICMG Bus Industrial Single Board Computer

Summary of NuPRO-630

  • Page 1

    Nupro-630 pentium ® -ii bus-100mhz vga full size all-in-one pc/104 vga crt interface supports dma33 wdt doc usb irda picmg bus industrial single board computer.

  • Page 2

    © copyright 1999 all rights reserved. Manual rev 1.0, february 22.1999 this manual is copyrighted and all rights are reserved. It is not allow any non authorization in copied, photocopied, translated or reduced to any electronic or machine readable in whole or in part form without prior written cons...

  • Page 3

    Contents • i contents chapter1 general information ...............................................................1-1 1.1 m ajor f eatures .............................................................................................. 1-2 1.2 s pecifications .............................................

  • Page 4

    Ii •contents 3.13 usb p orts c onnector ............................................................................... 3-10 chapter4 award bios setup ........................................................................4-1 4.1 m ain m enu ............................................................

  • Page 5: Chapter-1

    General information 1-1 chapter-1 general information the nupro-630 is a bus-100mhz ali ® bx-level chipset design picmg bus pentium ® ii industrial single board (i.S.B.) cpu card with features combine together to make it an ideal all-in-one industrial single board computer, enhanced i/o effects with...

  • Page 6

    1-2 general information 1.1 major features ü picmg bus supported. ü pc/104 bus connector for 8/16-bit supported. ü one axial-horizontal type slot-1 socket for intel™ pentium ® ii 233∼450 mhz processors. ü ali™ m1621 bx-level chipset. ü three pieces dimm sockets supports dram up to 1.5 gb. ü fast pci...

  • Page 7

    General information 1-3 1.2 specifications ² cpu: one intel pentium ® ii 233/266/300/333/400/450mhz. ² bus interface: picmg bus, pc/104 bus. ² chipset: ali™ m1621 bx-level with bus-100mhz facility. ² data bus: 64-bit ² processing ability: 64-bit ² svga controller: s3 ® 86c375 chipset with 2mb memory...

  • Page 8

    1-4 general information ² flash memory disk: socket for diskonchip™ (doc), support up to 72mb flash memory disk. ² extra power input: provides one 4-pin extra dc +5v/+12v power input connector. ² cmos: real-time clock/calendar and battery backup by ds12b887 or equivalent device. ² power supply volta...

  • Page 9: Chapter-2

    Hardware installation 2-1 chapter-2 hardware installation this ch apter provides the information on how to install the hardware of nupro-630. At first, please follow up sections 1.3, 2.1 and 2.2 in check the delivery package and carefully unpacking. Following after, the jumpers setting of switch, wa...

  • Page 10

    2-2 hardware installation 2.2 caution on unpacking and before installation first of all, please follow with all necessary steps of section 2.1 in protection the nupro-630 from electricity discharge. With refer to section 1.3, please check the delivery package again with following steps: 1. Unpacking...

  • Page 11

    Hardware installation 2-3 2.3 nupro-630’s layout nupro-630’s layout 2.4 quick listing of jumpers jp1 ( 1-2 on ) — bus-clock select jp3 ( 3-4,7-8 on ) — frequency multiplier setting of system bus to processor core jp4 ( 1-2 off ) — rtc clear jumper jp5 ( 1-2 on ) — watchdog active select jp6 ( 5-6 on...

  • Page 12

    2-4 hardware installation 2.5 quick listing of connectors bz1: on-board buzzer cn1: internal 5-pin keyboard connector cn2: reset pin cn3: speaker connector cn4: keylock connector cn5: hdd led connector cn6: ps/2 power switch connector cn7: power 4-pin connector cn9: 1st ide connector cn10: 2nd ide c...

  • Page 13

    Hardware installation 2-5 2.6 jumper setting description a jumper pin-set is on as a shorted circuit with a plastic cap inserted over two pins. A jumper pin-set is off as a open circuit with a plastic cap inserted over one or no pin(s) between pins. The below figure 2.2 shows the examples of differe...

  • Page 14

    2-6 hardware installation 2.7 setting the bus-clock frequency the nupro-630 provides all necessary by jumper setting in using bus-clock frequency as the system bus clocking with jp1 setting as following: l bus-clock frequency setting of jp1: bus-clock frequency jp1 * 100mhz 1-2 66mhz 2-3 2.8 frequen...

  • Page 15

    Hardware installation 2-7 2.9 setting the rtc configuration the nupro-630 provides a setting for the selection of the rtc clear jumper by jp4 setting as following: l cmos setting of jp4: cmos clear jumper jp4 normal * off clear cmos on 2.10 system memory dram the nupro-630 provides a wide range on-b...

  • Page 16

    2-8 hardware installation 2.12 watch-dog timer there are three access cycles of watch -dog timer as enable, refresh and disable. The enable cycle should proceed by read port 443h. The disable cycle should proceed by read port 043h. A continue enable cycle after a first enable cycle means refresh. On...

  • Page 17

    Hardware installation 2-9 if the refresh cycle does not active before wdt period cycle, the on board wdt architecture will issue a reset or nmi cycle to the system. The watch -dog timer is controlled by two i/o ports. 443h i/o read the enable cycle. 443h i/o read the refresh cycle. 043h i/o read the...

  • Page 18

    2-10 hardware installation 2.14 diskonchip address setting the nupro-630 provides a u17 socket for install the diskonchip module. A jp7 may select the starting memory address of the diskonchip (d.O.C.) for avoid the mapping area with any other memory devices. If you have another extra memory devices...

  • Page 19: Chapter-3

    Connection 3-1 chapter-3 connection this chapter gives all necessary information of the peripheral's connections, switches and indicators. 3.1 power and fan connectors the nupro-630 provides one 4-pin dc-power connector as following cn7 pin information. And also provides one 3-pin fan out connector ...

  • Page 20

    3-2 connection 3.2 ide's led, key-lock and reset button the nupro-630 h as one led ( ld1 ) indicates out power-on status. And the following provides the pin information for ide's led indicator, key-lock and reset button connections from cn5, cn4 and cn2. L cn5 : ide led connector pin no. Description...

  • Page 21

    Connection 3-3 3.4 pci e-ide drive connector two standard 40-pin header daisy-chain driver connect ors provide as cn9 and cn10 with following pin assignment. Total four ide (integrated device electronics) drivers may connect. Cn9 (ide 1) : primary ide connector l cn9 : ide interface connector pin no...

  • Page 22

    3-4 connection cn10 (ide 2) : primary ide connector l cn10 : ide interface connector pin no. Description pin no. Description 1 reset 2 ground 3 data 7 4 data 8 5 data 6 6 data 9 7 data 5 8 data 10 9 data 4 10 data 11 11 data 3 12 data 12 13 data 2 14 data 13 15 data 1 16 data 14 17 data 0 18 data 15...

  • Page 23

    Connection 3-5 3.6 parallel port connector a standard 26-pin flat cable driver connector provides as cn13 with following pin assignment for connection to parallel printer. L cn13 : parallel port connector pin no. Description pin no. Description 1 strobe 2 data 0 3 data 1 4 data 2 5 data 3 6 data 4 7...

  • Page 24

    3-6 connection l cn16 : fdd connector pin no. Description pin no. Description 1 ground 2 reduce write 3 ground 4 n/c 5 ground 6 n/c 7 ground 8 index# 9 ground 10 motor enable a# 11 ground 12 drive select b# 13 ground 14 drive select a# 15 ground 16 motor enable b# 17 ground 18 direction# 19 ground 2...

  • Page 25

    Connection 3-7 1 data carrier detect (dcd) 2 receive data (rxd) 3 transmit data (txd) 4 data terminal ready (dtr) 5 ground (gnd) 6 data set ready (dsr) 7 request to send (rts) 8 clear to send (cts) 9 ring indicator (ri) l cn18 : serial port 10-pin header (com2) pin no. Description pin no. Descriptio...

  • Page 26

    3-8 connection 3.9 keyboard connectors the nupro-630 offers two possibilities for keyboard connections to external ps/2 type keyboard at cn24 and an internal 5-pin header at cn1. L cn1 : 5-pin header keyboard connector pin no. Description 1 keyboard clock 2 keyboard data 3 n/c 4 ground 5 +5v l cn24 ...

  • Page 27

    Connection 3-9 3.11 vga-crt connector the nupro-630 provides two possible connectives of vga-crt connections. One standard db-15 external vga connector as following cn22 pin information. Another internal 10-pin header for vra-crt connection as following cn17 pin information. L cn22 : 15-pin db-15 fe...

  • Page 28

    3-10 connection 3.12 ir connector the nupro-630 provides a 6-pin internal ir communication connector as following cn21 pin information. L cn21 : 6-pin ir connector pin description pin description 1 vcc 4 ground 2 firrx 5 irtx 3 irrx 6 cvroff 3.13 usb ports connector the nupro-630 provides a internal...

  • Page 29: Chapter-4

    Award bios setup 4-1 chapter-4 award bios setup the nupro-630 uses the award pci/isa bios for the system configuration. The award bios setup program is designed to provide the maximum flexibility in configuring the system by offering various options which could be selected for end-user requirements....

  • Page 30

    4-2 award bios setup 4.1 main menu once you enter the award bios cmos setup utility, the main menu will appear on the screen. The main menu allows you to select from several setup functions and two exit choices. Use the arrow keys to select among the items and press to enter the sub-menu. Note that ...

  • Page 31

    Award bios setup 4-3 4.2 standard cmos setup the standard setup is used for the basic hardware system configuration. The main function is for data/time and floppy/hard disk drive settings. Please refer to the following screen for the setup. When the ide hard disk drive you are using is larger than 5...

  • Page 32

    4-4 award bios setup 4.3 bios features setup this section allows you to configure your system for the basic operation. You have the opportunity to select the system’s default speed, boot -up sequence, keyboard operation, shadowing and security..

  • Page 33

    Award bios setup 4-5 4.4 chipset features setup this section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as dram and the external cache. It also coordinates the communi...

  • Page 34

    4-6 award bios setup 4.5 integrated peripherals the ide hard drive controllers can support up to two separate hard drives. These drives have a master/slave relationship which is determined by the cabling configuration used to attach them to the controller. Your system supports two ide controllers--a...

  • Page 35

    Award bios setup 4-7 4.6 power management setup the power management setup allows user to configure the system for saving energy in a most effective way while operating in a manner consistent with his own style of computer use..