1. DL manuals
  2. IBT Technologies
  3. Motherboard
  4. IB710
  5. User Manual

IBT Technologies IB710 User Manual

Summary of IB710

  • Page 1

    Ib710 socket 370 little board with vga/audio/lan user’s manual version 1.0b.

  • Page 2: Acknowledgments

    Ii ib710 user’s manual acknowledgments award is a registered trademark of award software international, inc. Ps/2 are trademarks of international business machines corporation. Intel and celeron are registered trademarks of intel corporation. Microsoft windows is a registered trademark of microsoft ...

  • Page 3: Table of Contents

    Ib710 user’s manual iii table of contents introduction...............................................................1 installations ..............................................................5 installing the cpu........................................................... 6 installing the memory (...

  • Page 4

    Iv ib710 user’s manual this page was intentionally left blank..

  • Page 5: Introduction

    Introduction ib710 user’s manual 1 introduction product description the ib710 little board is a high-performance multimedia little board based on the intel 440bx agpset. It features a socket 370 architecture that supports intel celeron and coppermine processors using 66mhz and 100mhz front side bus ...

  • Page 6: Checklist

    Introduction 2 ib710 user’s manual checklist your ib710 package should include the items listed below. Damaged or missing items should be reported to your supplier. • the ib710 embedded little board • this user’s manual • one compact disc containing the following: • intel pci ide driver and flash me...

  • Page 7: Specifications

    Introduction ib710 user’s manual 3 specifications processor supported socket 370 support intel celeron / coppermine, 300mhz~800mhz, 66mhz/100mhz bus speed chipset intel 440bx agpset bios award bios supports acpi, dmi, pnp system memory 1x dimm socket support up to 256mb capacity 3.3v supported ecc s...

  • Page 8: Board Dimensions

    Introduction 4 ib710 user’s manual board dimensions.

  • Page 9: Installations

    Installations ib710 user’s manual 5 installations this section provides information on how to use the jumpers and connectors on the ib710 in order to set up a workable system. The topics covered are: installing the cpu.............................................................6 installing the memo...

  • Page 10: Installing The Cpu

    Installations 6 ib710 user’s manual installing the cpu the ib710 embedded little board supports a socket 370 processor socket for intel celeron/coppermine processors. The socket 370 processor socket comes with a lever to secure the processor. Raise this lever to about a 90 ° angle to allow the inser...

  • Page 11: Installing The Memory (Dimm)

    Installations ib710 user’s manual 7 installing the memory (dimm) the ib710 embedded little board supports one 168-pin dimm socket for a maximum total memory of 256mb in sdram type. The memory capacities supported are 32mb, 64mb, 128mb and 256mb. Installing and removing dimms to install the dimm, loc...

  • Page 12: Setting The Jumpers

    Installations 8 ib710 user’s manual setting the jumpers jumpers are used on the ib710 to select various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your needs. The following lists the connectors on ib710 an...

  • Page 13: Jumper Locations On Ib710

    Installations ib710 user’s manual 9 jumper locations on ib710 disk on chip jp2: lcd power setting jp7: com3/4 rs232 +5v / +12v power setting jp4, jp5, jp6: rs232/rs422/rs485 (com2) selection jp3: atx function selection jp14: com1/2 rs232 +5v / +12v power setting note: jp9, jp10, j9, j19 are for manu...

  • Page 14

    Installations 10 ib710 user’s manual sw1(3): cpu bus speed selector bus speed sw1(3) switch setting 100mhz off 66mhz on sw1(5-8): cpu frequency selector the table below shows the correct setting to match the cpu frequency. Frequency multiplier cpu frequency (66mhz) cpu frequency (100mhz) sw1(5-8) 4....

  • Page 15

    Installations ib710 user’s manual 11 jp2: lcd power setting jp2 setting function pin 1-2 short/closed 3.3v pin 2-3 short/closed 5v jp3: atx function selection jp3 setting function pin 1-2 short/closed atx function pin 2-3 short/closed normal jp4, jp5, jp6: rs232/rs422/rs485 (com2) selection jp4, jp5...

  • Page 16

    Installations 12 ib710 user’s manual jp7: com3/4 rs232 +5v / +12v power setting jp7 pin # signal name jp7 signal name jp7 pin # 1 +5v +5v 2 3 pin 9 (com3) pin 9 (com4) 4 5 +12v +12v 6 com3 settings: pin 1-3 short = +5v, pin 3-5 short = +12v com4 settings: pin 2-4 short = +5v, pin 4-6 short = +12v jp...

  • Page 17

    Installations ib710 user’s manual 13 jp14: com1/2 rs232 +5v / +12v power setting jp14 pin # signal name jp14 signal name jp14 pin # 1 +5v +5v 2 3 pin 9 (com1) pin 9 (com2) 4 5 +12v +12v 6 com1 settings: pin 1-3 short = +5v, pin 3-5 short = +12v com2 settings: pin 2-4 short = +5v, pin 4-6 short = +12...

  • Page 18: Connectors On Ib710

    Installations 14 ib710 user’s manual connectors on ib710 the connectors on ib710 allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors on ib710 and their respective functions. Connector locations on ib71...

  • Page 19: Connector Locations On Ib710

    Installations ib710 user’s manual 15 connector locations on ib710 disk on chip jp1: vga crt connector j2: lcd panel connector j5: 18-bit lvds connector (df13-20) j4: audio connector system fan power connector j7: cpu fan power connector j18, j17: eide connectors j12: rj45 connector j13: parallel por...

  • Page 20

    Installations 16 ib710 user’s manual p1: peripheral power connector the p1 peripheral power connector has the following pin assignments. Pin # signal name 1 -12v 2 ground 3 -5v 4 ground p2: main power connector the p2 main power connector has the following pin assignments. Pin # signal name 1 +5v 2 ...

  • Page 21

    Installations ib710 user’s manual 17 j1: system function connector the system function connector provides interfaces for light indicators of system activities (hdd/power) and computer status switches. Hard disk drive led reset switch turbo led connector atx power on switch green function power led a...

  • Page 22

    Installations 18 ib710 user’s manual power led and keylock: pins 11 - 15 the power led indicates the status of the main power switch. The keylock switch, when closed, will disable the keyboard function. Pin # signal name 11 power led 12 no connect 13 ground 14 keylock 15 ground turbo led connector: ...

  • Page 23

    Installations ib710 user’s manual 19 j2: lcd panel connector j2 is the pin header for flat panel lcd displays. The following shows the pin assignments of this connector. Signal name pin # pin # signal name +12v 1 2 +12v ground 3 4 ground 5v/3.3v 5 6 5v/3.3v enavee 7 8 ground p0 9 10 p1 p2 11 12 p3 p...

  • Page 24

    Installations 20 ib710 user’s manual flat panel display interface pin descriptions mono mono mono color color color color color color color color color ss dd dd tft tft tft tft tft+hr stn-ss stn-ss stn-dd stn-dd pin name 8-bit 8-bit 16-bit 9/12/16 bit 18/24 bit 36-bit 18/24 bit 8-bit (4bp) 16-bit (4...

  • Page 25

    Installations ib710 user’s manual 21 j5: 18-bit lvds connector (df13-20) signal name pin # pin # signal name tx0- 2 1 tx0+ ground 4 3 ground tx1- 6 5 tx1+ 5v/3.3v 8 7 ground nc 10 9 nc tx2- 12 11 tx2+ ground 14 13 ground txc- 16 15 txc+ 5v/3.3v 18 17 enabkl +12v 20 19 +12v j6: system fan power conne...

  • Page 26: Specifications:

    Installations 22 ib710 user’s manual jp8: irda connector this connector is used for an irda connector for wireless communication. Pin # signal name 1 +5v 2 no connect 3 ir rx 4 ground +5v irrx irtx n.C. Gnd 5 ir tx j10: digital i/o connector this 10-pin digital i/o connector supports ttl levels and ...

  • Page 27

    Installations ib710 user’s manual 23 j14: serial ports j14a (com1), j14b (com2), j14c (com3) and j14d (com4/ttl level) are the onboard serial ports on the ib710. Pin # signal name (rs-232) 1 dcd, data carrier detect 2 rxd, receive data 3 txd, transmit data 4 dtr, data terminal ready 5 ground 6 dsr, ...

  • Page 28

    Installations 24 ib710 user’s manual j12: rj45 connector j12, an rj45 connector, is for the external lan connector. The ib710 supports both 10mbps and 100mbps lan facilities. Signal name pin # pin # signal name led1+ 1 6 led1- rx+ 2 7 rx- led2- 3 8 ground led2+ 4 9 ground tx+ 5 10 tx- - j13: paralle...

  • Page 29

    Installations ib710 user’s manual 25 j15: floppy drive connector j15 of the ib710 is a 34-pin header and will support up to 2.88mb floppy drives. Signal name pin # pin # signal name ground 1 2 rm/lc ground 3 4 no connect ground 5 6 no connect ground 7 8 index ground 9 10 motor enable 0 ground 11 12 ...

  • Page 30

    Installations 26 ib710 user’s manual j18, j17: eide connectors j18 is the primary ide connector. J17 is the secondary ide connector. Signal name pin # pin # signal name reset ide 1 2 ground host data 7 3 4 host data 8 host data 6 5 6 host data 9 host data 5 7 8 host data 10 host data 4 9 10 host dat...

  • Page 31

    Installations ib710 user’s manual 27 signal name pin # pin # signal name reset ide 1 2 ground host data 7 3 4 host data 8 host data 6 5 6 host data 9 host data 5 7 8 host data 10 host data 4 9 10 host data 11 host data 3 11 12 host data 12 host data 2 13 14 host data 13 host data 1 15 16 host data 1...

  • Page 32

    Installations 28 ib710 user’s manual con1, con2: pc-104 connector con1 and con2 are dual-in-line pin headers that support pc-104 modules. Con1 consists of 64 pins and con2 has 40 pins. The following table shows the their pin assignments. Con1 con2 pin signal name pin signal name pin signal name pin ...

  • Page 33: Watchdog Timer Configuration

    Installations ib710 user’s manual 29 watchdog timer configuration the function of the watchdog timer is to reset the system automatically and is defined at i/o port 0443h. To enable the watchdog timer and allow the system to reset, write i/o port 0443h. To disable the timer, write i/o port 0441h for...

  • Page 34

    Installations 30 ib710 user’s manual this page was intentionally left blank..

  • Page 35: Bios Setup

    Bios setup ib710 user’s manual 31 bios setup this section describes the different settings available in the award bios that comes with the ib710 embedded board. The topics covered in this section are as follows: bios introduction .........................................................................

  • Page 36: Bios Introduction

    Bios setup 32 ib710 user’s manual bios introduction the award bios (basic input/output system) installed in your system’s rom provides critical low-level support for standard devices such as disk drives, parallel port and serial ports. It also adds virus and password protection, as well as special s...

  • Page 37

    Bios setup ib710 user’s manual 33 rom pci/isa bios cmos setup utility award software, inc. Standard cmos setup integrated peripherals bios features setup supervisor password chipset features setup user password power management setup ide hdd auto detection pnp/pci configuration save & exit setup loa...

  • Page 38: Standard Cmos Setup

    Bios setup 34 ib710 user’s manual standard cmos setup “standard cmos setup” allows you to record some basic hardware configurations in your computer system and set the system clock and error handling. If the embedded little board is already installed in a working system, you will not need to select ...

  • Page 39

    Bios setup ib710 user’s manual 35 time the time format is: hour : 00 to 23 minute : 00 to 59 second : 00 to 59 to set the time, highlight the “time” field and use the / or +/- keys to set the current time. Primary hdds / secondary hdds the onboard pci ide connectors provide primary and secondary cha...

  • Page 40

    Bios setup 36 ib710 user’s manual note: the specifications of your drive must match with the drive table. If your hard disk drive type is not matched or listed, you can use type user to define your own drive type manually. Drive a / drive b these fields identify the types of floppy disk drive a or d...

  • Page 41: Bios Features Setup

    Bios setup ib710 user’s manual 37 bios features setup this section allows you to configure and improve your system and allows you to set up some system features according to your preference. Rom / pci isa bios bios features setup award software, inc. Virus warning : disabled video bios shadow : enab...

  • Page 42

    Bios setup 38 ib710 user’s manual quick power on self test this choice speeds up the power on self test (post) after you power up the system. If it is set to enabled, bios will skip some items. Boot sequence this field determines the drive that the system searches first for an operating system. The ...

  • Page 43

    Bios setup ib710 user’s manual 39 typematic delay (msec) when the typematic rate is enabled, this item allows you to set the time interval for displaying the first and second characters. By default, this item is set to 250msec. Security option this field allows you to limit access to the system and ...

  • Page 44: Chipset Features Setup

    Bios setup 40 ib710 user’s manual chipset features setup this menu controls the configuration of the embedded board chipset. Rom pci/isa bios chipset features setup award software inc. Auto configuration : enabled auto detect dimm/pci clk : disabled sdram ras-to-cas delay : 3 spread spectrum : disab...

  • Page 45

    Bios setup ib710 user’s manual 41 dram data integrity mode set this field to ecc if the dram installed in the system supports it. Otherwise, do not reset the default of non-ecc. System bios cacheable when enabled, access to the system bios rom addressed at f0000h-fffffh is cached, provided that the ...

  • Page 46

    Bios setup 42 ib710 user’s manual delayed transaction the chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select enabled to support compliance with pci specification version 2.1. The default setting is enabled. Agp aperture size the field sets aperture size o...

  • Page 47: Power Management Setup

    Bios setup ib710 user’s manual 43 power management setup the power management setup allows you to save energy of your system effectively. It will shut down the hard disk and turn off video display after a period of inactivity. Rom pci/isa bios power management setup award software, inc. ** reload gl...

  • Page 48

    Bios setup 44 ib710 user’s manual video off method this field defines the video off features. There are three options. V/h sync + blank (default): blank the screen and turn off vertical and horizontal scanning. Dpms: allows the bios to control the video display card if it supports the dpms feature. ...

  • Page 49

    Bios setup ib710 user’s manual 45 when enabled, the system can be powered on through the external modem connected. Irq 8 break suspend you can enable or disable the monitoring of irq 8 (real time clock) so it does not awaken the system from suspend mode. Resume by alarm with the use of atx power, th...

  • Page 50: Pnp/pci Configuration

    Bios setup 46 ib710 user’s manual pnp/pci configuration this option configures the pci bus system. All pci bus systems on the system use int#, thus all installed pci cards must be set to this value. Rom pci/isa bios pnp/pci configuration award software inc. Pnp os installed : no used mem base addr :...

  • Page 51

    Bios setup ib710 user’s manual 47 irq3/4/5/7/9/10/11/12/14/15, dma0/1/3/5/6/7 assigned to these fields allow you to determine the irq/dma assigned to the isa bus and is not available to any pci slot. Used mem base addr select a base address for the memory area used by any peripheral that requires hi...

  • Page 52: Load Bios Defaults

    Bios setup 48 ib710 user’s manual load bios defaults this option allows you to load the troubleshooting default values permanently stored in the bios rom. These default settings are non-optimal and disable all high-performance features. Rom pci/isa bios cmos setup utility award software, inc. Standa...

  • Page 53

    Bios setup ib710 user’s manual 49 to load setup defaults value to cmos sram, enter “y”. If not, enter “n”..

  • Page 54: Integrated Peripherals

    Bios setup 50 ib710 user’s manual integrated peripherals this option allows you to determine your hard disk configuration, mode and port. Rom pci/isa bios integrated peripherals award software inc. Ide hdd block mode : enabled onboard fdc controller : enabled ide primary master pio : auto onboard se...

  • Page 55

    Bios setup ib710 user’s manual 51 on-chip primary/secondary pci ide the integrated peripheral controller contains an ide interface with support for two ide channels. Select enabled to activate each channel separately. Usb keyboard support select enabled if your system contains a universal serial bus...

  • Page 56: Supervisor / User Password

    Bios setup 52 ib710 user’s manual supervisor / user password these two options set the system password. Supervisor password sets a password that will be used to protect the system and setup utility. User password sets a password that will be used exclusively on the system. To specify a password, hig...

  • Page 57: Ide Hdd Auto Detection

    Bios setup ib710 user’s manual 53 ide hdd auto detection this option detects the parameters of an ide hard disk drive, and automatically enters them into standard cmos setup screen. Rom pci/isa bios standard cmos setup award software, inc. Hard disks type size cyls head precomp landz sector mode pri...

  • Page 58: Vga Drivers Installation

    Vga drivers installation 54 ib710 user’s manual vga drivers installation this section provides information on how to install the c&t 69000 vga drivers that come with your ib710 board. Please follow the instructions set forth in this section carefully. If the vga drivers come in floppy diskettes, it ...

  • Page 59

    Vga drivers installation ib710 user’s manual 55 installing the drivers for windows 95/98 the following section describes the normal display driver installation procedures for windows 95/98. Use the following procedures when installing the display drivers for windows 95/98. 1. Click start, then setti...

  • Page 60

    Vga drivers installation 56 ib710 user’s manual installing the drivers for windows nt 4.0 once you are in the windows nt 4.0 environment, follow the procedures below to install the vga drivers that come with your embedded board. 1. Click the start button, then go to settings and click on control pan...

  • Page 61

    Vga drivers installation ib710 user’s manual 57 this page was intentionally left blank..

  • Page 62: Audio Drivers Installation

    Audio drivers installation 58 ib710 user’s manual audio drivers installation this section provides information on how to install the audio drivers for ess solo-1 es1938s that come in floppy diskettes with your ib710 board. Please follow the instructions set forth in this section. It is recommended t...

  • Page 63

    Audio drivers installation ib710 user’s manual 59 installing the audio driver for windows 95 1. Turn on the computer and start windows 95. 2. Insert the cd containing the ess solo-1 es1938s audio drivers for windows 95. 3. The cd autoruns and shows a screen with options for you to choose. Click on s...

  • Page 64

    Audio drivers installation 60 ib710 user’s manual installing the audio driver for windows 98 1. Turn on the computer and start windows 98. 2. Insert the diskette containing the ess solo-1 es1938s audio drivers for windows 98. 3. The cd autoruns and shows a screen with options for you to choose. Clic...

  • Page 65

    Audio drivers installation ib710 user’s manual 61 installing the audio driver for windows nt 1. Turn on the computer and start windows nt. 2. Insert the diskette or cd containing the ess solo-1 es1938s audio drivers for windows nt. 3. The cd autoruns and shows a screen with options for you to choose...

  • Page 66: Lan Drivers Installation

    Lan drivers installation 62 ib710 user’s manual lan drivers installation this section describes lan features and driver installation of the onboard realtek rtl8139 ethernet controller. The following items are covered in this section: introduction.........................................................

  • Page 67: Introduction

    Lan drivers installation ib710 user’s manual 63 introduction realtek rtl8139 is a 32-bit 10/100mbps ethernet controller for pci local bus-compliant pcs. It supports bus mastering architecture, and auto-negotiation feature which make it possible to combine one common type of ethernet cabling – an rj-...

  • Page 68

    Lan drivers installation 64 ib710 user’s manual installing lan drivers for windows 98/windows 2000 this section describes the procedure to install windows 98 and windows 2000 drivers for realtek rtl8139 pci fast ethernet controller. 1. Executing windows 98/windows2000 will auto-detect your system co...

  • Page 69

    Lan drivers installation ib710 user’s manual 65 installing lan drivers for windows nt this section describes the procedure to install windows nt v3.5, v3.51 & v4.0 driver for realtek rtl8139 pci fast ethernet hardware. When you are in windows nt : 1. In the main group of windows nt, select the contr...

  • Page 70: Appendix

    Appendix 66 ib710 user’s manual appendix a. Post codes b. I/o port address map c. Interrupt request lines (irq).

  • Page 71: A. Post Codes

    Appendix ib710 user’s manual 67 a. Post codes post (power on self test) codes are to determine problems during boot up. Below are the codes for your reference. Post (hex) description cfh test cmos r/w functionality. C0h early chipset initialization: -disable shadow ram -disable l2 cache (socket 7 or...

  • Page 72

    Appendix 68 ib710 user’s manual post (hex) description 12h use walking 1’s algorithm to check out interface in cmos circuitry. Also set real-time clock power status, and then check for override. 14h program chipset default values into chipset. Chipset default values are modbinable by oem customers. ...

  • Page 73

    Appendix ib710 user’s manual 69 post (hex) description 47h initialize eisa slot 49h 1. Calculate total memory by testing the last double word of each 64k page. 2. Program writes allocation for amd k5 cpu. 4eh 1. Program mtrr of m1 cpu 2. Initialize l2 cache for p6 class cpu & program cpu with proper...

  • Page 74

    Appendix 70 ib710 user’s manual post (hex) description 7fh 1. Switch back to text mode if full screen logo is supported. -if errors occur, report errors & wait for keys -if no errors occur or f1 key is pressed to continue: wclear epa or customization logo. 82h 1. Call chipset power management hook. ...

  • Page 75: B. I/o Port Address Map

    Appendix ib710 user’s manual 71 b. I/o port address map each peripheral device in the system is assigned a set of i/o port addresses which also becomes the identity of the device. The following table lists the i/o port addresses used on the embedded little board. Address device description 000h - 01...

  • Page 76

    Appendix 72 ib710 user’s manual c. Interrupt request lines (irq) peripheral devices use interrupt request lines to notify cpu for the service required. The following table shows the irq used by the devices on the embedded little board. Level function irq0 system timer output irq1 keyboard irq2 inter...