- DL manuals
- IC Realtime
- Security Camera
- EL-470
- Operating manual
IC Realtime EL-470 Operating manual
Summary of EL-470
Page 1
Operating manual user's instructions vandal-proof dome dnr day / night weatherproof camera user’s manual products : el-470
Page 2
2 user’s manual.
Page 3
3 user’s manual contents ◑ general features ◑ installing & adjusting ◑ dimension & specification ◑ osd control button ◑ camera menu set up 1. Menu set up 2. Lens setting 3. Exposure setting 4. White balance setting 5. Ssdr setting 6. Backlight setting 7. Dnr3 setting 8. Day/night setting 9. Special s...
Page 4
4 user’s manual general features ◑ ultra high sensitivity - the built-in high sensitivity color ccd produces a clear image even in 0lux(b/w, ir-led on) or lower illumination. ◑ 600tv lines - by adopting a diagonal 6mm(1/3") 410,000 (ntsc) pixel, 470,000(pal) pixel sony ccd, the camera produces clear...
Page 5
5 user’s manual installing & components 1. Installation - using the l-wrench provided, loosen 4 screws by turning them and separate the dome cover - drill holes on the celling by matching to the holes on the case bed. Fix the case bed on the ceilling by using tapping screws. - pass the power and vid...
Page 6
6 user’s manual dimension & specification n o it c e n n o c & n o is n e m i d . 1 2. Specification dimension connection model ir led vandal dome ir led on : dc12v 650ma / ac24v 270ma dc auto iris varifocal lens(2.8mm-12mm) 146mm(w) * 105mm(h) * 146mm(d) 1400g image pick-up device tv system total pi...
Page 7
7 user’s manual osd control button 1. Osd button could be used when it needs to osd control. ▲ up button: moves the cursor upwards. Use this button to select an item or adjust the parameters. ▼ down button: moves the cursor downwards. Use this button to select an item or adjust the parameters. ◀ lef...
Page 8
8 user’s manual ● menu setup ● lens setting 1. Press the function setup switch. - main setup menu is displayed on the monitor screen. 3. The lens mode has sub menu items as listed below. - brightness : adjusts the video brightness. Using this function, you can control the screen brightness. 1. When ...
Page 9
9 user’s manual - focus adj : to adjust the dc lens focus correctly, you must activate the focus settings mode under each lens menu. Activate the focus settings mode, adjust the lens focus, and then deactivate the settings mode. ☞ note ■ if color rolling occurs when using a dc lens, set shutter to f...
Page 10
10 user’s manual ◆ agc(auto gain control) : the higher the gain level, the brighter the screen but the higher the noise. * off : deactivates the agc function. * low : allows automatic gain control from 5.3db to 32db. * high : allows automatic gain control from 5.3db to 37db. ◆ sens-up : when it is n...
Page 11
11 user’s manual ※ select one of the following 5 modes, as appropriate for your purpose. ◆ a tw : select this when the color temperature is between 1,700˚k and 1 1,000˚k. ◆ outdoor : select this when the color temperature is between 1,7 00˚k and 1 1,000˚k. (sodium light inclusion) ◆ indoor : select ...
Page 12
12 user’s manual ● backlight setting unlike conventional cameras, w-v chip camera is designed to deliver a distinctive subject and background at the same time, even when the subject is backlight, by using the features of the proprietary w-v dsp chip. 1. When the setup menu screen is displayed, selec...
Page 13
13 user’s manual blc setup hlc setup press set to return press set to return level top bottom left right level limits mask color mask tone top bottom left right low 38 109 54 121 middle night only black 1 5 120 5 172 ☞ note ■ because there can be a difference in the effectiveness of hlc according to...
Page 14
14 user’s manual 3. Set the dnr3 mode to 'on' and press the function setup switch. Then you can adjust the noise reduction level. ☞ note ■ you cannot set the dnr3 to ‘on’ or ‘off’ when the agc mode of the exposure menu is ‘off’. ■ when adjusting the noise reduction level in the dnr3 mode, remember t...
Page 15
15 user’s manual ◆ auto : the mode is switched to 'color' in a normal environment, but switches to 'b/w' mode when ambient illumination is low. To set up the switching time for auto mode, press the function setup switch. You can turn on or off the burst signal on b/w mode. - burst mode : you can tur...
Page 16
16 user’s manual 2. Select a desired mode using the function setup switch. Special image setup 1.Image adj 2.Monitor 3.Cam title 4.Sync 5.Motion det 6.Privacy 7.Language 9.Retrun 1.V-rev 2.H-rev 3.D-zoom 4.Dis 5.Font color 6.Sharpness 7.Return lcd off int off off english off off off white on ◆ image...
Page 17
17 user’s manual ☞ note ■ when the v-rev or h-rev mode is enabled, the text on the scr een does not fli p. ■ if you increase the sharpness level too high, the picture may become distorted or noise may appear. ☞ note ■ when the cam title menu is ‘off’, no title will be displayed on the monitor screen ...
Page 18
18 user’s manual ☞ note ■ when using ac power at 60hz(ntsc), 50hz(pal), frequency, you can use the l/l type synchronization. ■ when the power is dc 12v, the sync menu is fixed to the ‘int’ mode. ◆ motion det :this product has a feature that allows you to observe movement of objects in 8 different ar...
Page 19
19 user’s manual 1) when the special menu screen is displayed, press the function setup switch so that the arrow indicates 'privacy'. 2) set up the mode using the function setup switch. - area : you can select up to 12 privacy areas. - mode : determines whether to use the area selected in the area. ...
Page 20
20 user’s manual ● trouble shooting problem northing appears on the screen. ☞ check the power cable, power supply output and video connection between the camera and monitor. ☞ are the camera lens or the lens glass dirty? Clean the lens / glass with a soft clean cloth. ☞ adjust the monitor controls, ...
Page 21
21 user’s manual.
Page 22: Www.Icrealtime.Com
Www.Icrealtime.Com.