1. DL manuals
  2. IC Realtime
  3. IP Camera
  4. ICIP-MP2008IR
  5. Instruction Manual

IC Realtime ICIP-MP2008IR Instruction Manual

Manual is about: IR IP PTZ Camera

Summary of ICIP-MP2008IR

  • Page 1

    Ic realtime security solutions icip-mp2008ir: ir ip ptz camera instruction manual cameras: ip-ptz.

  • Page 2: Manual

    I c r e a l t i m e s e c u r i t y s o l u t i o n s icip-mp2008ir ip ptz camera instruction manual ic realtime 3050 n andrews ave ext pompano beach, fl 33064 phone 954.772.5327 • fax 866.860.3860

  • Page 3: Table Of Contents

    Table of contents 1. Features and specifications ....................................................................... 1 a. Overview .......................................................................................... 1 b. Features ...............................................................

  • Page 4: 1.A Overview

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 1 features and specifications this section outlines the primary features of the icrealtime icip-mp2008ir ip ptz camera. It also outlines basic architectural and engineering specifications. 1.A overview his ic realtime series product is an excelle...

  • Page 5

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 2 compression format h.264 video and g.711 audio enables high quality video recording while maintaining the lowest file sizes possible. Network operation full system control (including live view, playback, backup, ptz control, and system configur...

  • Page 6: 1.C Specifications

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 3 1.C specifications model mp2008ir camera image sensor 1/3” exmor cmos effective pixels 1280(h) x 960(v) scanning system progressive electronic shutter speed 1/1 ~ 1/30,000s min. Illumination color: 0.05lux@f1.4; b/w: 0.005lux@f1.4 s/n ratio mor...

  • Page 7

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 4 preset 80(icr-sd), 255(pelco-p/d) ptz mode 5 pattern, 8 tour, auto pan, auto scan speed setup human-oriented focal length/ speed adaptation power up action auto restore to previous ptz and lens status after power failure idle motion activate pr...

  • Page 8: 1.D Dimensions

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 5 power supply ac 24v/2.2a (±10%) power consumption 10.5w, 26w (ir on, heater on) working environment -40ºc ~ 60ºc / less than 90% rh ingress protection ip66 dimensions Φ204.7(mm) x 359.9(mm) weight 7.8kg 1.D dimensions ptz module.

  • Page 9

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 6 wall mount.

  • Page 10: Camera Installation

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 7 camera installation this section outlines the proper way to mount and install an icip-mp2008ir series ip ptz camera. Suitable methods of installing the ipc include either ceiling installation, pole installation, or wall installations. Note: bel...

  • Page 11: 2.B Step By Step Guide

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 8 2.B step by step guide step 1: install wall mount bracket begin by first assuring that the wall you are mounting it on can support the bolts you will be using to hold the mount. Assure the wall can sustain the weight of the ptz by up to four (4...

  • Page 12

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 9 2.C connections & dip switch settings this section will cover all connections of the mp2008ir ptz.  note: for network connectivity, you would only need to use the rj45 for network access and use the power terminals to provide power to the ptz....

  • Page 13

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 10 dip switch settings are used to change the address, protocol, baud rate and parity of the ptz. This is not needing to be changed if connecting it just over the network. You can make these changes by connecting direct to the camera through its ...

  • Page 14

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 11 parity: note the chart below to set your parity. You should not need to change the parity in most cases. Baud rate: note the chart below to set your baud rate. This may need to be changed due to specifications in your controlling device and al...

  • Page 15: Web Gui Operation

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 12 web gui operation this section outlines how to assign an ip address to the camera, and how to access and control the ipc via it’s built in web ineterface. 3.A network connection step 1: ensure the camera is physically connected to your network...

  • Page 16

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 13 step 2: follow the on screen prompts to install the plugin when you first access the ip camera over your web browser, you will be prompted to install the plugin. See below: step 3: login to the camera with the default credentials by default, t...

  • Page 17: 3.C Ptz Controls

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 14 3.C ptz controls one of the primary features and functions of the ipc ptz series cameras is the ability to pan/tilt/zoom. Read on for a step-by- step guide on how to control the multiple functions of the icip-mp2008ir once you are logged in, y...

  • Page 18

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 15  note: to set these options above, you will need to click on the 'setup' menu option and choose the 'ptz' > 'function' menu. Once in the ptz 'function' menu, you may set the different functions. Please reference our other manuals for detailed...

  • Page 19: Report

    I c r e a l t i m e s e c u r i t y s o l u t i o n s 16 appendix: toxic or hazard materials report note this user manual is intended for reference only. Slight differences may be found in the user interface as products continually develop. All designs and software herein are subject to change witho...