1. DL manuals
  2. ICandy
  3. Stroller
  4. APPLE 2 PEAR
  5. Instruction Manual

ICandy APPLE 2 PEAR Instruction Manual

Manual is about: Baby Strollers

Summary of APPLE 2 PEAR

  • Page 1

    Apple 2 pear instruction manual.

  • Page 2: Welcome To The World Of

    Welcome to the world of icandy important: keep these instructions for future reference. Read carefully. Your child’s safety may be affected if you do not follow these instructions. Warning: never leave your child unattended. If you have any problems or queries, please contact your local stockist or ...

  • Page 3

    3 apple 2 pear.

  • Page 4

    4 apple 2 pear icandy apple 2 pear instructions contents section 1 - chassis section 2 - seat unit section 3 - bassinette section 4 - car seat adaptors section 5 - apple 2 pear converter system section 6 - apple 2 pear newborn nest section 7 - apple 2 pear tandem car seat adaptors section 8 - icandy...

  • Page 5

    5 apple 2 pear section 1 - chassis contents chassis including: front wheels x 2 • basket • rear wheels x 2 • rear axle / brake bar assembly seat unit including: seat frame • seat fabric • safety harness and pads • pvc raincover 1. To open the chassis: release the hold together strap by depressing bo...

  • Page 6

    6 apple 2 pear 2. Fitting the brake bar / rear axle assembly: turn the chassis upside down. Position the brake bar / rear axle assembly with the brake levers uppermost and push down onto rear leg. Pull firmly on each side of the brake bar/rear axle assembly to check that both sides are securely lock...

  • Page 7

    7 apple 2 pear 4 5 4. To remove the rear wheels: lift the rectangular shaped locking catch and remove the wheel from the axle. Note: inflating the air filled tyres (available separately as an accessory). Use only the pump provided or a similar hand / foot pump device. Never use a compressor or other...

  • Page 8

    8 apple 2 pear 6. Front wheels: can be selected in fixed or swivel position by rotating grey disc behind wheels. (swivel position is required for folding chassis). Useful tip: if the swivel device is rotated in use the wheels will automatically lock into fixed position when the wheel is next in line...

  • Page 9

    9 apple 2 pear 8. To fold chassis: (remove seat/bassinette before folding): ensure the basket is empty and apply brakes. Switch front wheels to swivel mode. (see 6). Squeeze the central handle button and depress the circular secondary lock button on the left arm of the chassis. Slide the handle do...

  • Page 10

    10 apple 2 pear 1 3 section 2 - seat unit (all seat units) (shown with raspberry blue flavour pack hood - available separately). 1. Attaching the hood: attach the hood clips into the receptor brackets on the seat frame ensuring both locking tabs are fully engaged. 2. Rotate canopy rearwards, opening...

  • Page 11

    11 apple 2 pear 5 6 4. Fold down rear fabric over the seat frame and adjust hood to the desired position. Useful tip: the peak of the hood is extendible and can be folded back into the hood when not required. 5. Removal of hood: lift the rear fabric up over the seat frame and insert the hood removal...

  • Page 12

    12 apple 2 pear 5. Depress both locking tabs firmly before removing from sockets. 6. Attaching seat unit: insert the seat attachment arms into the main connectors on the chassis. Push down on each side to engage. Check security of seat by pulling upwards. Useful tip: the seat unit can be positioned ...

  • Page 13

    13 apple 2 pear 8 9 8. To remove the seat unit: (remove child first). Depress the circular grey button on each side of the seat simultaneously and lift the seat unit upwards. 9. To fold the chassis with the apple 2 seat attached: folding is shown with seat unit rearward facing. Ensure the basket is ...

  • Page 14

    14 apple 2 pear 10. Folding of the chassis itself is the same as in steps 7 & 8 - section 1. Squeeze the central handle button and depress the circular secondary lock button on the left arm of the chassis. Slide the handle downwards to its lowest point and push down sharply to disengage the main ...

  • Page 15

    15 apple 2 pear safety harness securing your child using the 5 point safety harness: push the left and right connectors (a) into the buckle housing & click together. Adjust the length of the straps using slider buckles (b). To release connectors: squeeze the connectors inwards (c) and pull out of th...

  • Page 16

    16 apple 2 pear section 3 - bassinette contents bassinette including: • mattress • padded liner • handle • hood • apron • raincover 1. Initial assembly: remove the apron, bassinette mattress and liner to access the base board. Useful tip: the liner is secured by press studs under the hood also. 2. P...

  • Page 17

    17 apple 2 pear 3. Operation of the hood: pull up the handle as shown until the locking devices engage with a positive "click". Check that the handle is secure before placing your baby in the bassinette. Important: do not attempt to over extend the handle. 4. To lower the hood: depress both grey loc...

  • Page 18

    18 apple 2 pear 6. Pull down the stabiliser frame and lock onto the basket bar as shown. 7. Removal of bassinette: release and store the stabiliser bar. Depress the circular grey release buttons as shown and lift bassinette. 6 7.

  • Page 19

    19 apple 2 pear bassinette information bassinette internal measurements l x w: 77cm x 32cm (guide only for bassinette mattress size). External base measurements l x w: 79cm x 35.5cm warning: the icandy apple 2 bassinette is only suitable for a child who cannot sit up unaided, roll over and cannot pu...

  • Page 20

    20 apple 2 pear section 4 - car seat adaptors available separately to fit the maxi cosi mico air protect and maxi cosi titan air protect infant carrier car seats. 1. Fitting the car seat adapters: depress the central button and fit the adaptors into the left and right sides of the main chassis conne...

  • Page 21

    21 apple 2 pear 2a 2b 2a. Fitting the infant car seat - maxi cosi mico air protect (rearward facing only). Ensure adaptors are aligned with the fixing slots on each side of the car seat. Press down firmly to ensure the car seat is firmly locked onto the adaptors. Once fitted lift the car seat to ens...

  • Page 22

    22 apple 2 pear 3a 3b 3a. Removing the infant car seat - maxi cosi mico air protect. Depress the 2 grey buttons on either side of the car seat to disengage the locking devices and lift. Useful tip: it may be easier to do this if the handle is positioned to the rear of the car seat. 3b. Removing the ...

  • Page 23

    23 apple 2 pear 4. Removing the car seat adaptors: depress the central release button as shown and lift adaptors. 4.

  • Page 24

    24 apple 2 pear a b section 5 - apple 2 pear converter system contents: box 1: as apple single pushchair (see section 1). Box 2: apple 2 pear conversion system (a) apple 2 pear seat unit with frame (b). Pvc rain cover (not shown). For single pushchair assembly and operation, including fitting the fl...

  • Page 25

    25 apple 2 pear attaching the apple 2 pear conversion system. 1a. Attaching the upper adaptor arms: depress the central grey button and insert both of the upper adaptor arms into the main connectors on the chassis. The extended portion of the arms should face towards the front of the pushchair. Note...

  • Page 26

    26 apple 2 pear 1c. Align the lower receptor bracket with the ridges on the frame attachment device. Depress the spring clip on the inside of the lower receptor bracket and slide the bracket down onto the frame attachment device. Press down firmly until "click" is heard. Check that the lower recepto...

  • Page 27

    27 apple 2 pear 1d 1d. The lower receptor bracket should sit on the basket frame. Useful tip: you may need to slide the hold together strap to the side to ensure a positive fit of the seat attachment bracket. Warning: check that the apple 2 pear converter system is correctly fitted before use. Usefu...

  • Page 28

    28 apple 2 pear 2b 2a attaching the apple 2 pear seat units – (all seat units): (shown with raspberry blue flavour pack hood - sold separately). 2a. Orientate the seat unit to face forwards and insert the seat attachment arms into the apple 2 pear lower adapter brackets. Push down on each side to en...

  • Page 29

    29 apple 2 pear 3. To recline the seat unit (all seat units): depress the grey buttons simultaneously and rotate the seat to desired position. Note: the upper seat features 2 recline positions when in pear 2 tandem mode. This is to ensure there is no interference between upper and lower seat units. ...

  • Page 30

    30 apple 2 pear 5 5. To fold the chassis with the apple 2 pear seat units or with lower pear 2 newborn nest attached: ensure the basket is empty and apply the brakes. Switch the front wheels to swivel mode. (see 6 - section 1). Recline the upper seat before folding. Fully recline the rear seat frame...

  • Page 31

    31 apple 2 pear 6. Fold the chassis by following instructions in section 1, steps 8 & 9. Squeeze the central handle button and depress the circular secondary lock button on the left arm of the chassis. Slide the handle downwards to its lowest point and push down sharply to disengage the main locks a...

  • Page 32

    32 apple 2 pear section 6 - pear 2 newborn nest contents: 1 x newborn nest fabric including base, mattress and apron. The newborn nest fabric has been designed to fit on the apple 2 pear seat frames. 1. Converting the seat frames - removing the seat unit fabric: remove the hood as shown in section 2...

  • Page 33

    33 apple 2 pear 3. Once the fabric is off the frame, pass the webbing security strap over the foot end of the frame. Your frame is now ready to fit your newborn nest. 4. Pear 2 newborn nest fabric. Remove the apron. Useful tip: the newborn nest can be fitted with the mattress and base board in place...

  • Page 34

    34 apple 2 pear 6. Secure the webbing safety straps around the frame and through the metal rings. Attach the velcro security strap. 7. Secure each set of velcro loops around the seat frame and wrap the upper edge of the newborn nest fabric over the seat frame. 8. Attach the press stud closures at ea...

  • Page 35

    35 apple 2 pear 9. Fit the flavour pack by inserting the locking tabs into the receptor brackets and carefully extend hood fabric over the top of the seat / nest frame. Note: there is no zip fitting of the hood onto the newborn nest fabric. Useful tip: the peak of the hood is extendible and can be f...

  • Page 36

    36 apple 2 pear pear 2 newborn nest information newborn nest internal measurements l x w: 73 cm x 31cm (guide only for bassinette mattress size). Warning: the icandy pear 2 newborn nest is only suitable for use with the pear 2 converter system for a child who cannot sit up unaided, roll over and can...

  • Page 37

    37 apple 2 pear 10a 10b 10a. Attaching the pear 2 newborn nests: (shown with raspberry blue flavour pack hood - sold separately) orientate the lower newborn nest to face forwards and insert the attachment arms into the apple 2 pear lower adapter brackets. Push down on each side to engage. 10b. Orien...

  • Page 38

    38 apple 2 pear 11. To remove the newborn nests: (remove child first). Depress the circular grey button on each side of the frames simultaneously and lift the newborn nest upwards. 11.

  • Page 39

    39 apple 2 pear section 7 - apple 2 pear tandem car seat adaptors available separately to fit the maxi cosi mico air protect and maxi cosi titan air protect infant carrier car seats. 1a. Fitting the upper car seat adapters: depress the central button and fit the adaptors into the left and right side...

  • Page 40

    40 apple 2 pear 2a 2a. Fitting the lower infant car seat - maxi cosi mico air protect or titan air protect (rearward facing only). Ensure adaptors are aligned with the fixing slots on the car seat. Press down firmly to ensure the car seat is firmly locked onto the adaptors. Once fitted lift the car ...

  • Page 41

    41 apple 2 pear 2b 2b. Fitting the upper infant car seat - maxi cosi mico air protect or titan air protect (rearward facing only). Ensure adaptors are aligned with the fixing slots on the car seat. Press down firmly to ensure the car seat is firmly locked onto the adaptors. Once fitted lift the car ...

  • Page 42

    42 apple 2 pear 3a. Removing the infant car seats - maxi cosi mico air protect or titan air protect (all positions). Depress the 2 grey buttons on either side of the car seat to disengage the locking devices and lift. Useful tip: it may be easier to do this if the handle is positioned to the rear of...

  • Page 43

    43 apple 2 pear 4a. Removing the upper car seat adaptors: depress the central release button as shown and lift adaptors. 4b. Removing the lower car seat adaptors: depress the moulded release button as shown and lift adaptors. Removing the apple 2 pear conversion system 5a. Removing the upper apple 2...

  • Page 44

    44 apple 2 pear 5b. Removing the lower apple 2 pear adaptor brackets: depress the spring clip at the base of the attachment bracket and lift upwards and off the frame attachment devices. Gently push the frame attachment devices forward away from the rear legs and store with the fitting bracket. Usef...

  • Page 45

    45 apple 2 pear 1 3 section 8 - icandy apple 2 pear configurations “which mode am i in today?” the icandy apple 2 pear is a versatile multi-functional design which enables you to adapt your stroller to your family’s requirements. 1. Chassis & seat unit forward facing – 3 position recline 2. Chassis ...

  • Page 46

    46 apple 2 pear 4. Chassis and maxi cosi mico air protect infant car seat (rearward facing only) 5. Chassis & maxi cosi titan air protect infant car seat (rearward facing only) 4 5.

  • Page 47

    47 apple 2 pear new pear 2 tandem 1. 2 x seat units - upper & lower (both seats are same size & universal. Upper seat is restricted to 2 position incline by moulding to prevent interference) 2. 2 x newborn nests - facing toe to toe (both upper & lower newborn nests are identical and universal) 3. 2 ...

  • Page 48

    48 apple 2 pear 4. 2 x maxi titan air protect car seats (both facing rearwards - lower car seat adaptors are swan neck shaped, upper adaptors are straight) pebble infant car seat (rearward facing only) 5. 1 x upper seat (facing forward), 1 x newborn nest (facing forward) 6. 1 x upper seat (facing fo...

  • Page 49

    49 apple 2 pear 7. 1 x upper seat (facing forwards), 1 x lower maxi cosi titan air protect car seat (facing rearwards) 8. 1 x lower newborn nest (facing forward), 1 x upper maxi cosi mico air protect car seat (facing rearwards) 9. 1 x lower newborn nest (facing forward), 1 x upper maxi cosi titan ai...

  • Page 50

    50 apple 2 pear 10. 1 x lower seat unit (facing forwards), 1 x upper maxi cosi mico air protect car seat (facing rearwards) 11. 1 x lower seat unit (facing forwards), 1 x upper maxi cosi mico titan air protect car seat (facing rearwards) 10 11.

  • Page 51

    51 apple 2 pear section 9 - accessories accessories available for the icandy apple 2 pear: 1. Apple 2 pear flavour pack hood 2. Footmuff 3. Apple 2 main / pear 2 upper car seat adaptors 1 3 2.

  • Page 52

    52 apple 2 pear 4. Apple 2 pear converter system 5. Apple 2 pear lower car seat adaptors 6. Apple 2 pear seat fabric 4 6 5.

  • Page 53

    53 apple 2 pear 7. Pear 2 newborn nest fabric 8. Palm sunshade 9. Parasol/cupholder clamp 7 9 8.

  • Page 54

    54 apple 2 pear 10. Cupholder 11. Lifestyle changing bag 12. Rear air tyres available separately 10 12 11.

  • Page 55

    55 apple 2 pear section 10 - important safety information important: read these instructions carefully before use and keep them for future reference. Your child’s safety may be affected if you do not follow these instructions. Your icandy apple 2 pear is intended for children from birth up to 15kg p...

  • Page 56

    56 apple 2 pear important safety information about your icandy apple 2 pear • this vehicle is intended for children from birth up to 15kg (3 years approximately). Maximum weight for basket - 5kg (11lbs). • parcels, accessory items or both if placed on the unit may cause it to become unstable. • plea...

  • Page 57

    57 apple 2 pear • icandy apple 2 bassinette is not intended for use as an infant restraint device in a motor vehicle. • the icandy apple 2 bassinette is only suitable for use on the icandy apple 2 chassis. When using the icandy pear 2 newborn nest • never add any additional mattress, pillow, comfort...

  • Page 58

    58 apple 2 pear section 11 - general use • your icandy apple 2 pear requires regular inspection and maintenance. • regularly inspect the locking devices, parking devices, harness assembly, catches, seat and bassinette attachment devices and fittings to ensure they are secure and in full working orde...

  • Page 59

    59 apple 2 pear warranty your product warranty is our quality promise to you. We guarantee that this product is free from defects in workmanship and manufacturing materials at the time of purchase. During the production process your product was subject to various quality checks however if despite ou...

  • Page 60

    60 apple 2 pear where your warranty applies your warranty applies in the country of purchase only. The warranty applies to the first owner and is not transferable. What to do in case of defect if you feel there is a problem with your icandy product please contact your original approved stockist. Imp...

  • Page 61

    61 apple 2 pear.

  • Page 62

    62 apple 2 pear.

  • Page 63

    63 apple 2 pear.

  • Page 64

    Apple 2 pear the icandy apple 2 pear is a quality product of british design and is distributed by tobil & co. Pty ltd. For further technical information please contact your place of purchase, e-mail: info@tobil.Com.Au or visit www.Icandyworld.Com/au/en imported into and distributed in australia by: ...