1. DL manuals
  2. Ice-O-Matic
  3. Beverage Dispenser
  4. Hotel Dispenser CD300
  5. Service & Installation Manual

Ice-O-Matic Hotel Dispenser CD300 Service & Installation Manual

Manual is about: Hotel Dispenser

Summary of Hotel Dispenser CD300

  • Page 1

    Service/installation manual hotel dispenser model - cd300 mile high equipment 11100 east 45th ave denver, colorado 80239 part number 9081292-01 print date 04/02.

  • Page 2

    Introduction cd300 page 1 to the owner or user: this product manual is a source of information about the installation, start up, cleaning, maintenance and repair of the product. Table of contents introduction page 1 specification/limitations page 2 diagrams page 3 uncrating page 4 ice machine instal...

  • Page 3

    Specifications cd300 page 2 specifications and limitations this dispenser is designed to dispense cubed ice only and to be installed and operated indoors, in a controlled enviroment. Its minimum and maximum operating temperature limits are the same as those for the ice machine. Limitations: l must m...

  • Page 4

    Diagrams cd300 page 3.

  • Page 5

    Uncrating cd300 page 4 remove the carton from the skid. Cut the plastic straps that secure the leg kit to the skid and remove the box. Use the dispenser carton as a cushion and lay the dispenser down on its back. Remove the bolts holding the skid to the machine, and separate the skid from the dispen...

  • Page 6

    Ice machine installation cd300 page 5 all models: place the dispenser in the location where it will be used. Level the top edge of the dispenser front to back and left to right with the adjustable legs. Place the ice machine on the dispenser and secure it to the dispenser with the hardware and strap...

  • Page 7

    Utility connections cd300 page 6 drain connections -follow all applicable codes. As ice melts in the dispenser, the water must be drained away. It is critical that a proper drain be connected to the dispenser. Remember that this is a gravity drain system, the drain tubing must slope down a minimum o...

  • Page 8

    Initial start up and use cd300 page 7 final check list 1. Is the ice machine properly installed? 2. Is the dispenser level? 3. Has the water supply been connected to the ice machine? 4. Has the proper power been connected to the ice machine and dispenser? Note: when electrical power is supplied to t...

  • Page 9

    Sanitation / maintenance cd300 page 8 schedule an ice system represents a sizable investment of time and money in any company’s business. In order to receive the best return on that investment, periodic maintenance is required. It is the user responsibility to see that the machine is properly mainta...

  • Page 10

    Component identification cd300 page 9 view when sink assembly is removed. Rotor as seen from the top. Inside view of ice chute. Rotor shaft..

  • Page 11

    Maintenance cd300 page 10 regular inspection and maintenance will provide the best assurance of trouble free operation. Begin by removing the sink assembly. Check the action of the ice chute and return springs. Return springs check and tighten fasteners clean out the lower drain pan. Pour hot water ...

  • Page 12

    Service diagnosis cd300 page 11 symptom probable cause possible correction does not dispense. No power to dispenser. Check for power. Ice chute not all the way up. Push ice chute up. No ice in hopper. Check ice machine, it may be off or the dispenser’s storage capacity may have been exceeded. Dispen...

  • Page 13

    Adjustments cd300 page 12 the gear motor cam must be properly adjusted to properly position the dispensing rotor. 1. Disconnect electrical power to the dispenser. 2. Locate the sink key, unlock sink and remove it from the dispenser. 3. Observe the position of the rotor through the cube chute. The ro...

  • Page 14

    Removal and replacement cd300 page 13 rotor 1. Disconnect electrical power to the dispenser and ice machine. 2. At the back, remove two bolts securing the ice machine to the dispenser. If a bin thermostat is being used, pull the thermostat capillary tube up and out of the hopper. 3. Push the ice mac...

  • Page 15

    Wiring diagram cd300 page 14 button dispensing model cd300p.

  • Page 16

    Schematic diagram cd300 page 15 button dispensing model cd300p.

  • Page 17

    Wiring diagram cd300 page 16 coin mechanism cd300c.

  • Page 18

    Schematic diagram cd300 page 17 coin mechanism cd300c cd300c.

  • Page 19

    Wiring diagram cd300 page 18 key card cd300k.

  • Page 20

    Schematic diagram cd300 page 19 key card cd300ccd300k.

  • Page 21: Dispenser

    Before calling for service cd300 page 20 check these things. 1. Is the dispenser plugged in? 2. Has the dispenser’s internal switch been switched to the on position? 3. Is the ice machine plugged in? 4. Has the ice machine’s internal switch been switched to the on position? 5. Is there ice in the di...