- DL manuals
- Ice-O-Matic
- Ice Maker
- ICEU060
- Service And Installation Manual
Ice-O-Matic ICEU060 Service And Installation Manual
Summary of ICEU060
Page 1
Mile high equipment 11100 east 45th ave denver, colorado 80239 part number 9081291-01 print date 11/01 model-iceu060 ice undercounter series cubers service and installation manual.
Page 2
Introduction iceu060 page 1 to the owner or user: this product manual is a source of information about the installation, start up, cleaning, maintenance, and repair of the product. Table of contents introduction page 1 specifications/limitations page 2 installation page 3-5 initial start up page 6 h...
Page 3
Specifications iceu060 page 2 specifications: 24 hour bin storage basic maximum ref type. Model number capacity capacity electrical fuse size ounces iceu060 55 lbs. 28 lbs. 115/60/1 15 r134a, 9.5 oz operating requirements: minimum maximum air temperature 50 ° f 100 ° f water temperature 40 ° f 100 °...
Page 4
Installation iceu060 page 3 location: prior consideration for the location of the ice machine shall include: installation location to be indoors with a minimum room temperature of 50 °f and with a maximum room temperature of 100 °f. The incoming water temperature to the machine should be between 40 ...
Page 5
Installation iceu060 page 4 water supply and drain connection: 1. The recommend water supply line is ¼ inch o.D. Copper tubing. The minimum incoming water pressure should be 20 psig. 2. Connect the water supply tubing to the water inlet fitting (3/4 hose thread) at the rear of the icemaker. An optio...
Page 6
Installation iceu060 page 5 final check: 1. Is the cabinet level? 2. Have all the electrical and piping connection been made? 3. Has the voltage been tested and checked against the nameplate rating? 4. Is the unit plugged into a separate electrical circuit? 5. Is the water supply line shut off valve...
Page 7
Initial start up iceu060 page 6 1. Open the water supply valve. 2. Move electrical breaker or switch to the on position. 3. Remove the front panel. 4. Check the cube size control shaft, it should be in a preset position. If not, rotate the control shaft clockwise until the unit comes on. Note: cube ...
Page 8
How it works iceu060 page 7 component description cube size control the cube size control is located in the front of the control box, behind the front panel. The sensing capillary tube of the cube size control is routed out of the control box into its bulb holder on the evaporator coil. It is a reve...
Page 9
Component location iceu060 page 8.
Page 10
How it works iceu060 page 9 water system freezing cycle the refrigeration process creates cold temperatures within the evaporator coils and removes heat from the water sprayed up into the inverted ice cube cups. When enough heat is removed, the water changes into ice, and forms where it is the colde...
Page 11
How it works iceu060 page 10 refrigeration system freezing cycle the ice cubes are formed in an inverted mold that is refrigerated. The refrigeration process begins at the compressor. There, refrigerant vapor is compressed and flows from the compressor through the discharge line as a high temperatur...
Page 12
How it works iceu060 page 11 refrigeration system harvest cycle (when the cubes are released) the ice cubes have been formed in an inverted mold that was refrigerated. Now the refrigeration system will change to warm the cube mold and release the cubes. The process begins at the compressor. There, r...
Page 13
Operation and adjustment iceu060 page 12 the information shown below covers a wide range of air and water temperatures. It is intended as a guideline only, and is based on data compiled from new clean units. Allow a variation from each end of the range given. Refrigeration system pressures: freeze c...
Page 14
Sanitizing and cleaning iceu060 page 13 an ice-o-matic ice machine represents a sizable investment of time and money in any company’s business. In order to receive the best return for that investment, it must receive periodic maintenance. It is the user’s responsibility to see that the unit is prope...
Page 15
Service diagnosis iceu060 page 14 symptom possible cause suggested correction unit will not run. Blown fuse or breaker. Replace fuse and check for cause of blown fuse or breaker. Compressor cyles low voltage. Check voltage at the supply to the intermittenly. Building. Check circuit for overloading. ...
Page 16
Component replacement iceu060 page 15 bin thermostat 1. Unplug the icemaker to disconnect electrical power. 2. Remove screws and cabinet front panel. 3. Remove screws and the control box cover, disconnect electrical wires from the bin thermostat control. 4. Dismount the bin thermostat from the contr...
Page 17
Component replacement iceu060 page 16 spray platform 1. Unplug the icemaker to disconnect electrical power. 2. Open ice bin door. 3. Pull out on the left side and remove curtain assembly. 4. Lift the spray platform up and pull out to get to the water hose at the base of the platform. 5. Pull hose of...
Page 18
Component layout iceu060 page 17.
Page 19
Wiring diagram iceu060 page 18.