DL manuals
Ice
Game
Whack N Win
Service Manual

Ice Whack N Win Service Manual - “Sensitiv

Page of 20

Download

Print this page

Bookmark us

How to Check if your game is in Calibration.

Step 1: Coin up the game.

Step 2: Using the Mallet to strike the “Hit Pad” as hard

as you can! (See Illustration).

Step 3: If the lights travel to the top of the tower, rebound

back down and land in the “Sensitivity Target Zone” then

your game is Calibrated. (see Illustration)

Step 4 : If the lights do not land in the “Sensitivity Target

Zone” then you will need to adjust OPTION 8 in program-

ming. See A-E below:

A) Open the cabinets front drawer and inside you will find the

User Control Panel.

Press the “PROG” button once and the “Right Balloon” will Dis-

play the option you are adjusting.

IF you accidentally hit a

wrong button and the game is not responding normally…

then turn off/on the game. (cycle power and start over)

C) Press the “SELECT” button until the “Balloon Display” reads 08.

(You will need to press “SELECT” 8 times)

D) Press the “UP” or “Down” button to change the “SENSITIVITY

VALUE” ( The Marquee BONUS DISPLAY on top of the tower

will indicate the new “SENSITIVITY VALUE”. The “Balloon Dis-

play” should remain at 08)

Decrease the Value of Option 8 if the lights do not rebound off

of the top of the tower. (Degrease Marquee Value Display by

pressing “Down” button)

Increase the Value of Option 8 if the lights rebound off of the

top of the tower and travel past the “Sensitivity Target

Zone” (Increase Marquee Value Display by pressing “UP” button)

E) Once you have Increased or Decreased the Marquee value in

option 8 you must

press the “PROG”

button to exit.

F) Repeat Steps 1—4

until your game is

Calibrated.

IMPORTANT: RECORD ALL SETTINGS ON THE CERTIFICATE LOCATED ON

THE SIDE OF THE FRONT DRAWER - OR— USE THE REVERSE SIDE OF THIS

PAPER IF IT CONTAINS A CALIBRATION CERTIFICATE.

“Sensitiv

ity

Tar

t Z

e”

** Note ** The “Sensitivity Target Zone”

is between the two highest numbers on

the Tower’s Score Chart. Your Tower’s

Score Chart might differ from the picture

shown.

CAL

IBRA

Marquee Display (Change Value)

Increasing Value = Less Rebound

Decreasing Value = More Rebound

Balloon

Display

Option 08

Sensitivity

Setting

STEP 2: Whack the “Hit Pad” as hard as

you can with the Mallet! (Do this after

you “coin up” the game.)

CAL

IBRA

« ‹ Prev 9 10 11 12 13 14 15 Next › »

Summary of Whack N Win

Page 1
1 whack n win service manual innovative concepts in entertainment, inc 10123 main street clarence, ny 14031 www.Icegame.Com (716) 759-0360 i.C.E. Tech support.
Page 2
2 table of contents safety and warnings 3 game assembly 4 - 8 programming 9 tower score charts 10 sensitivity calibration 11 service upper marquee access 12 changing tower score values 13 power supply 14 piezo assembly replacement tower lighting 15 spare parts list 16 warranty 17 revision g 8/19/201...
Page 3: Ac Power Information
3 safety and warnings before you begin warning: when installing this game, a grounded a.C. Receptacle must be used. Failure to do so could result in injury to yourself or others. Failure to use a grounded receptacle could also cause improper game operation, or damage to the electronics. Note: this g...
Page 4
4 step 1: open bottom access panel to expose main board. Remove lower light housing panel to access wiring. Remove the upper light housing panel. Step 2: install 2 1/4—20 x 1 1/4 bolts half way in the light housing’s guide tabs as shown with short arrows. Slide the light housing onto the base and st...
Page 5
5 step 3: cut the wire tie shown and all the other below. This will allow you to take one connector harness at a time and insert it through to the bottom where the main board is located. Be careful not to snag and disconnect any other of the other wire harnesses while doing so. Step 4: connect the f...
Page 6
6 step 5: while holding the upper light housing remove the two 1/4-20 x 1-1/4 screws using a # 3 phillips screw driver on each side and slide the light housing down being careful not to pinch any of the wire harnesses. Attach the light housing using four flat screws on each side (only one side is sh...
Page 7
7 step 7: attach the bonus marquee using four allen bolts. Replace the access panel door. Step 8: from the back of the game, attach the right side balloons using three allen bolts and washers. Step 9: from the back of the game install the right side balloon. Before lifting onto the cabinet, remove t...
Page 8
8 step 10: connect the light housing harnesses to j23, j24, and j25. The harnesses are labeled. J23 j24 j25 final: align the playfield score graphic and clear protective shield together and attach using 18 phillip screws. You will need to remove the protective film from the plastic before you instal...
Page 9
9 now that your game is assembled it is time to set the game options. The game’s scoring is shown on the tower score chart and it is based on price per play. See the next page for available tower score charts which can be replaced by calling service. You cannot change the values used in the tower sc...
Page 10
10 option min max inc 8 sensitivity 1 15 1 do not alter this option unless you review the section titled “how to calibrate the hit pad sensitivity”. Decreasing this value in- creases the sensitivity of the hit pad. Increasing this value will decrease the sensitivity of the hit pad. Payout options: 9...
Page 11
11.
Page 12: “Sensitiv
12 how to check if your game is in calibration. Step 1: coin up the game. Step 2: using the mallet to strike the “hit pad” as hard as you can! (see illustration). Step 3: if the lights travel to the top of the tower, rebound back down and land in the “sensitivity target zone” then your game is calib...
Page 13
13 accessing upper led light strips and display board to gain access to the electronics found inside the upper marquee, you will need to remove the upper marquee. Remove the four 1/4-20 x 7/8 bolts and washers holding the marquee in place (1). Open the back access door and unplug the harness (2 + 3)...
Page 14
14 changing the tower score card’s values to change the tower score card, remove the plastic shield and old tower score card. Starting from the top, reinstall the silver phillips screws. Power the game on and press the program button. Cycle through the options until option 11 is displayed. Enter the...
Page 15: Game Power Supplies
15 ia2010 wn201 game power supplies there are two power supplies located at the back of the game. The ia2010 power supply provides the +12 dc volts to the game board, lights, and outer fun lights. The wn2010 power supply provides the +5 dc voltage for the game logic and center leds. Wn1052x piezo se...
Page 16
16 +12 volt led fun lights. To access the bulb, unscrew the plastic cover. +5 volt led lights are mounted with the red w/brown wire loop at the top, over the mounting screw. Hand tight plastic nuts! Do not use power tools to install!! E00869wnx e00843.
Page 17
17 spare parts list electronics: e00418wnax asy (white 27 led tape strip) e00724wnax asy (rgb 81 led tape strip) e00724wnbx asy (rgb 54 led tape strip) e00724wnx asy (rgb 27 led tape strip) e00788wnbx asy (white lrg 60 led strip) e00843 "led, e10, cluster of 12 (medium)" e00869wnx "asy (5v rgb led, ...
Page 18
18 warranty policy i.C.E. Inc warrants all components in new machines to be free of defects in materials and workmanship for the period listed below: ■ 180 days on main pcb’s, computers & motors ■ 1 year on all lcd monitor panels ■ 90 days on all other electronic and mechanical components ■ 30 days ...
Page 19
D c b a 4 3 2 1 d c b a 4 3 2 1 j10 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 b l a c k w h it e /b r o w n w h it e /r e d w h it e /o r a n g e w h it e /y e ll o w w h it e /g r e e n w h it e /b l u e w h it e /v io le t w h it e /g r a y w h it e w h it e /b l a c k 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 ...
Page 20
D c b a 4 3 2 1 d c b a 4 3 2 1 date 3/31/14 descripti on system schematic filename wn1000x schematic.Vsdx page 2 of 2 revi sed 5/21/14 title whack n win part no. Wn1000x (2 of 2) required si gnatures engi neer manager vendor drawn by nicholas brancato red x 3, red x 3, red x 2 black x 2, black x 2 ...