IceTech SP 135 Technical & Service Manual

Manual is about: ICE CUBE MAKERS

Summary of SP 135

  • Page 1

    Ice tech ss / sp technical service manual 1 technical service manual ice cube makers models: icetech ss / sp 25 icetech ss / sp 35 icetech ss / sp 45 icetech ss / sp 60 icetech ss / sp 80 icetech ss / sp 135 carefully read the instructions contained in this manual since they provide important inform...

  • Page 2

    Ice tech ss / sp technical service manual 2 table of contents 1. Introduction ............................................................................................................................................... 3 1.1. Warnings .................................................................

  • Page 3

    Ice tech ss / sp technical service manual 3 1. Introduction 1.1. Warnings this appliance should be installed by approved technical service personnel. This plug should be accessible at all times. To reduce the risk of electrical shock, always disconnect the machine before cleaning or maintaining the ...

  • Page 4

    Ice tech ss / sp technical service manual 4 1.2. Description main features of the machine anti-blocking spray nozzles. Pump without seals. High pressure safety pressostats even in air-cooled machine. Large condensers (work well at high ambient temperatures; and reduce cooling water consumption in wa...

  • Page 5

    Ice tech ss / sp technical service manual 5 which closes the circuit with 3. A different blue wire goes to 2 on terminal g1 which at this moment is connecting 1 and 4. A red wire connects bin thermostat t1 and micros g1 and g2 which close the circuit with 4 and provide current via g1 to the timer g....

  • Page 6

    Ice tech ss / sp technical service manual 6.

  • Page 7

    Ice tech ss / sp technical service manual 7 1.4. Wiring diagram.

  • Page 8

    Ice tech ss / sp technical service manual 8 2. Specifications 2.1. Installation diagrams for inlet/outlet tubes and dimensions.

  • Page 9

    Ice tech ss / sp technical service manual 9 2.2. Consumption data, weights, crated dimensions and volumes model weight dimensions weight dimension water cond. Water total net l/hour fabr. L/hour l/hour (kg) x*y*z (kg) (m 3 ) ice tech 25a 5.1 5.1 34 350x470x590 40 0.20 ice tech 25w 18 5.1 23.1 34 350...

  • Page 10

    Ice tech ss / sp technical service manual 10 model high pressure low fuse refri. Pressure safety total consumption min max (gr) kg/cm 2 psi kg/cm 2 psi kg/cm 2 (a) (a) (w) ice tech 25a 190 15 214 17 250 2.5 2 10 360 ice tech 25w 190 15 214 17 250 2.5 2 10 360 ice tech 35a 230 15 214 17 250 2.5 2.2 1...

  • Page 11

    Ice tech ss / sp technical service manual 11 2.3. Production tables for ice flakers ice tech 25 tw/ta 45 40 35 30 25 20 15 10 35 6 8 10 12 13 13 14 14 30 9 12 13 15 16 17 17 17 25 12 15 16 18 19 20 20 20 20 15 17 19 20 22 22 23 23 15 17 19 21 23 24 25 25 25 10 19 21 23 25 26 26 27 27 5 21 23 25 26 2...

  • Page 12

    Ice tech ss / sp technical service manual 12 ice tech 45 tw/ta 45 40 35 30 25 20 15 10 35 11 15 19 21 23 24 25 25 30 17 21 25 27 29 30 31 31 25 23 27 30 32 34 36 36 36 20 27 31 35 37 39 40 41 41 15 32 35 39 41 43 45 45 45 10 35 39 42 45 47 48 49 49 5 38 42 45 48 50 51 52 51 ice tech 60 tw/ta 45 40 3...

  • Page 13

    Ice tech ss / sp technical service manual 13 10 43 48 52 55 57 59 60 60 5 46 51 55 58 61 62 63 63 ice tech 80 tw/ta 45 40 35 30 25 20 15 10 35 19 26 31 36 39 41 42 42 30 29 36 41 46 49 51 52 41 25 38 45 50 54 58 60 61 61 20 46 53 58 62 66 68 69 69 15 53 59 65 69 72 75 76 75 10 59 65 71 75 78 80 81 8...

  • Page 14

    Ice tech ss / sp technical service manual 14 3. Delivery & unpacking upon receipt, thoroughly inspect the packing container. If there appears to be damage to the container contact the shipper immediately. Unpack unit in the presence of delivery personnel noting any damage on the waybill. Itv packing...

  • Page 15

    Ice tech ss / sp technical service manual 15.

  • Page 16

    Ice tech ss / sp technical service manual 16 warning: do not leave packing materials (plastic bags, cardboard boxes, etc.) within reach of children. 4. Installation the ice cube maker is delivered on a small wooden pallet and is protected with a cardboard box and packaging. Loosen the cardboard box ...

  • Page 17

    Ice tech ss / sp technical service manual 17 bear in mind the previous considerations if the premises where the machines is located are very dusty, or smoky. If possible make arrangements so that the machine may be moved frontwise in order to carry out maintenance. 4.1. Recommended placement of unit...

  • Page 18

    Ice tech ss / sp technical service manual 18 c) chlorinated water: chlorine taste can be avoided by installing a carbon filter (note: you may encounter water with all aforementioned properties.) d) purified water: a 10% reduction in overall production may occur. 4.3. Connecting unit to water source ...

  • Page 19

    Ice tech ss / sp technical service manual 19 5. Operation 5.1. Preliminary check a) is machine levelled? B) are voltage and frequency of mains supply the same as indicated on rating plate? C) is drainage system working properly? D) is air circulation and room temperature adequate? (air-cooled models...

  • Page 20

    Ice tech ss / sp technical service manual 20 8) at the cycle’s end, there should be frost formed on the compressor inlet tube except for the last 50 mm. Important! Advise the final user on maintenance procedures which are not included in warranty, as well as those breakdowns caused by neglect of pro...

  • Page 21

    Ice tech ss / sp technical service manual 21 gearbox malfunction. Pressure values higher than 16 kg/cm2 may shorten compressor life and diminish ice production. Pressure can be regulated by rotating screw on pressure control valve (clockwise to increase pressure). One full turn is aquivalent to abou...

  • Page 22

    Ice tech ss / sp technical service manual 22 maintenance table: procedure monthly quarterly half yearly yearly biennial duration air condenser cleaning 30 minutes water condenser cleaning 90 minutes inyectors cleaning 30 minutes fabrication head filter cleaning 30 minutes water circuit cleaning 45 m...

  • Page 23

    Ice tech ss / sp technical service manual 23 4) prepare a solution of 50% phosphoric acid in distilled water. 5) distribute solution through condenser. (solution is more effective at 35°-40°c). Warning! Do not use hydrochloric acid air condenser 1) disconnect machine. 2) close water faucet. 3) clean...

  • Page 24

    Ice tech ss / sp technical service manual 24 16) allow machine to make ice for at least 15 minutes. Warning:** discard ice produced during cleaning procedure. 17) disconnect unit, place cover and check for water leaks. 18) change joint in water plug if necessary. 19) replace filters if necessary. (m...

  • Page 25

    Ice tech ss / sp technical service manual 25 these round wire gasket filters placed on either end of the water hose to mains, often become blocked in the first few days of use, especially when the plumbing installation is new. Clean them under a jet of water. Checking for water leaks this must be do...

  • Page 26

    Ice tech ss / sp technical service manual 26 9. Troubleshooting problem possible causes solution 1) none of the electrics work. A) the machine is not plugged in. A) plug the machine. B) the line fuse has blown. B) replace fuse. C) the current line is wrongly connected in the junction box. C) check c...

  • Page 27

    Ice tech ss / sp technical service manual 27 problem possible causes solution b) low water pressure. B) increase water pressure if possible. (this can often be done by removing flowmeter on faucet). C) faulty fan or pressostat. C) check fan and re-adjust pressostat or replace. D) inlet cooling water...

  • Page 28

    Ice tech ss / sp technical service manual 28 10) ice cubes are empty, rough edges and very white. A) insufficient water in water pan; unprimed pump. A) correct a major water leak. B) obstructed spray nozzles. B) clean. C) curtain does not close fully. C) adjust the curtain, clean scale (lime) on cur...