1. DL manuals
  2. ICharger
  3. Battery Charger
  4. 4010DUO
  5. User Manual

ICharger 4010DUO User Manual

Other manuals for 4010DUO: User Manual
Manual is about: Synchronous Balance Charger/Discharger

Summary of 4010DUO

  • Page 1

    Icharger synchronous balance charger/discharger 4010duo - 1 - 4010duo user's manual (v2.5) index user notice ....................................................................................................................................... - 4 - safety notes .....................................

  • Page 2

    Icharger synchronous balance charger/discharger 4010duo - 2 - nimh/nicd battery charge advanced setup .................................................................................. - 22 - nimh/nicd battery charge safety setup .....................................................................

  • Page 3

    Icharger synchronous balance charger/discharger 4010duo - 3 - channel regenerative mode ................................................................................................. - 37 - lithium battery extra discharge mode .....................................................................

  • Page 4

    Icharger synchronous balance charger/discharger 4010duo - 4 - user notice  safety notes please read the entire manual completely before using, to make sure you can use this device properly and more safely. 1. 4010duo is a dual port charger, but this does not mean you can charge/discharge any config...

  • Page 5

    Icharger synchronous balance charger/discharger 4010duo - 5 - transfer, sub-license, as well as other acts of infringement of software copyright is strictly prohibited, but apart from the restrictions prohibited by applicable law.  4010duo special features 1. The 4010duo uses advanced synchronous b...

  • Page 6

    Icharger synchronous balance charger/discharger 4010duo - 6 - device introduction  4010duo parts & interface introduction  4010duo buttons function & icons description buttons allow quick access to certain features when using 4010duo, familiarity with the icons on the interface will help you bette...

  • Page 7

    Icharger synchronous balance charger/discharger 4010duo - 7 - status-1 long press: measure internal resistance of ch-1 via long press on initial interface, and to pop up the parameters setup interface via long press when running program click: switch to the information display of ch-1 when running p...

  • Page 8

    Icharger synchronous balance charger/discharger 4010duo - 8 -  4010duo standard accessories usb data line #1 700mm power cable #1 600mm standard mini usb data line power input cable balance connector conversion board #2 70x44mm output cable #2 320mm suit for align/dualshy battery etc. Banana gold p...

  • Page 9

    Icharger synchronous balance charger/discharger 4010duo - 9 - the order of connection for charger  the power input ground cannot be connected with the output ground  single-channel (ch1 or ch2) connection notes 4010duo with the firmware version above v2.05 (including v2.05), please be sure to conn...

  • Page 10

    Icharger synchronous balance charger/discharger 4010duo - 10 -  connection for two battery packs  dual-channel connection notes  connection for channel asynchronous mode channel asynchronous mode: i.E. Ch-1 and ch-2 work independently. Go to memory setup→option→channel mode to select asynchronous...

  • Page 11

    Icharger synchronous balance charger/discharger 4010duo - 11 -  connection for channel synchronous mode channel synchronous mode: i.E. Ch-1 & ch-2 are controlled at the same time to charge/discharge one battery pack. Go to memory setup→option→channel mode to select synchronous. In this mode, the ma...

  • Page 12

    Icharger synchronous balance charger/discharger 4010duo - 12 - icharger charge/discharge setup & use 4010duo icharger can charge/discharge lipo, lilo, life, nihm, nicd , pb or nizn batteries, this manual is divided into three parts to explain and introduce the charger’s features for lipo/lilo/life, ...

  • Page 13

    Icharger synchronous balance charger/discharger 4010duo - 13 -  program add & manage click stop/start-x button on the initial interface to pop up the battery memory select window. 4010duo has 6 built-in programs before it enters to the market (shown in following picture), which cannot be deleted an...

  • Page 14

    Icharger synchronous balance charger/discharger 4010duo - 14 - after selecting the program to run, click confirmation to pop up run program window, as below: click yesto run the program, click no to cancel.  program running status press status-x button when running program to switch the multipage i...

  • Page 15

    Icharger synchronous balance charger/discharger 4010duo - 15 - press status-x button for 2 secondswhen running program to pop up modify interface, to modify the current and discharge voltage parameters online, as below: press stop/start-x button when running program to stop running, and press stop/s...

  • Page 16

    Icharger synchronous balance charger/discharger 4010duo - 16 - note: 1. Channel mode has asynchronous, synchronous available, see more details on page10 dual-channel connection notes . 2. If select synchronous mode, the maximum current setting will change from 40a to 70a. 3. If tick auto saves befor...

  • Page 17

    Icharger synchronous balance charger/discharger 4010duo - 17 - note:1. When the value of charge cells voltage exceeds the recommended value (lipo 4.2v, liio 4.1v, life 3.6v), the charger will sound an alarm with beep tones. As long as the user changes the values, the battery types and cells voltage ...

  • Page 18

    Icharger synchronous balance charger/discharger 4010duo - 18 - when switch to user balance mode on chg mode; the balance diff, balance set point, balance over charge and balance done delay are available, after setting, click" " to return to the previous interface. Note: if balance diff value is lowe...

  • Page 19

    Icharger synchronous balance charger/discharger 4010duo - 19 -  lipo/liio/life battery charge advanced setup click " " to enter lipo/liio/life battery advanced setup, after setting, click" "to return to the previous interface. Note: 1. When charging the over-discharged battery, the charger will det...

  • Page 20

    Icharger synchronous balance charger/discharger 4010duo - 20 -  lipo/liio/life battery discharge setup select program→discharge to enter discharge setup interface. Note: 1.The charger first discharges with constant current (cc) according to the user setting then turns to constant voltage (cv) when ...

  • Page 21

    Icharger synchronous balance charger/discharger 4010duo - 21 -  lipo/liio/life battery cycle setup select program→cycle to enter cycle setup interface, after setting click" " to return to the previous interface.  lipo/liio/life battery only balance feature select program→balance only to enter bala...

  • Page 22

    Icharger synchronous balance charger/discharger 4010duo - 22 -  nimh/nicd battery charge advanced setup click " " to enter nimh/nicd battery charge option setup interface, after setting click " " to return to the previous interface. Note: for the over-discharged nimh/nicd battery, the voltage may b...

  • Page 23

    Icharger synchronous balance charger/discharger 4010duo - 23 -  nimh/nicd battery cycle setup select program→cycle to enter cycle setup interface, see details about setting on page21 lipo/liio/life battery cycle setup.  pb battery charge/discharge setup after adding program, it will switch to pb b...

  • Page 24

    Icharger synchronous balance charger/discharger 4010duo - 24 -  pb battery charge safety setup click " " to enter charge safety setup interface, see details about setting on page19 lipo/liio/life battery charge safety setup.  pb battery discharge setup select program→discharge to enter discharge s...

  • Page 25

    Icharger synchronous balance charger/discharger 4010duo - 25 -  nizn battery charge advanced setup click " " to enter nizn advanced setup interface, see details about setting on page19 lipo/liio/life battery charge advanced setup.  nizn battery charge safety setup click " " to enter charge safety ...

  • Page 26

    Icharger synchronous balance charger/discharger 4010duo - 26 - 4010duo parameters setup  4010duo parameters setup press tab/sys button for 2 secondson the initial interface to enter the system menu interface, setting and testing of the system parameters, storage and servo can be completed on this i...

  • Page 27

    Icharger synchronous balance charger/discharger 4010duo - 27 -  beep tone setup select system menu→charger setup→beep tone to enter the setup interface. Note: tick the appropriate tone, and then go to volume adjustment bar to adjust the volume; if the beep tone is not ticked the corresponding volum...

  • Page 28

    Icharger synchronous balance charger/discharger 4010duo - 28 -  power supply setup select system menu→charger setup→power supply to enter the setup interface. After selecting input source, click the " " followed by the option, enters the relevant power supply setting to set the parameters, after se...

  • Page 29

    Icharger synchronous balance charger/discharger 4010duo - 29 -  communication settings select system menu→ charger setup→ communication to enter the setup interface. See detailed information about communication port protocol in icharger duo protocol. Go to the website http://www.Jun-si.Com/uploadfi...

  • Page 30

    Icharger synchronous balance charger/discharger 4010duo - 30 - note: user calibration has ch-x channel calibration and other variables calibration two options, users can calibrate charger for one channel alternatively. If user selects user calibration, the corresponding message will appear in the in...

  • Page 31

    Icharger synchronous balance charger/discharger 4010duo - 31 - select delete to pop up the log file delete dialogbox, select yes to delete this file, select no to cancel.  servo test select system menu→extra function→servo test to enter servo test interface; insert servo into j1 or j2 port to test ...

  • Page 32

    Icharger synchronous balance charger/discharger 4010duo - 32 -  pulse measurement select system menu→extra function→pulse test to enter the pulse test interface, only j2 port supports the input signal of pulse measurement.  usb & sd card use 4010duo is the hid device of usb, supported by windows s...

  • Page 33

    Icharger synchronous balance charger/discharger 4010duo - 33 - 4010duo firmware upgrades ① go to the website http://www.Jun-si.Com/uploadfiles/upgrader.Rar to download above ver1.9 version upgrader zip file " ", and extract to any disk on the pc. ② open the extract directory x:\upgrader\upgrader.Exe...

  • Page 34

    Icharger synchronous balance charger/discharger 4010duo - 34 - ⑤ click the iron " " on the lower right corner, then the upgrade progress bar will appear on the lower left corner, a tone sounds for upgrade completion when the upgrade progress bar has completed. Note: 1. Upgrade failed in the case of ...

  • Page 35

    Icharger synchronous balance charger/discharger 4010duo - 35 - use logview for 4010duo first, gratitude to the development team of logview, more details please see http://www.Logview.Info.  communication steps  to install the logview software, start the procedure of x:\ logview \ logviewinstaller....

  • Page 36

    Icharger synchronous balance charger/discharger 4010duo - 36 - 2) choose device →choose device and port; 3) choose junsi icharger4010duo in the following options of device, and then choose the correct communication port; 4) start icharger charge/discharge mode, then click start recording to record d...

  • Page 37

    Icharger synchronous balance charger/discharger 4010duo - 37 - important notes  the charging principle for reflex charge mode  power regenerative mode  channel regenerative mode channel regenerative mode note: reflex charge mode only supports nimh and pb battery. Does not support lithium battery....

  • Page 38

    Icharger synchronous balance charger/discharger 4010duo - 38 -  lithium battery extra discharge mode you can expand the icharger’s discharge power capacity by connecting the external capacity resistance. You should pay special attention when expanding the discharge circuit. The balance port must be...

  • Page 39

    Icharger synchronous balance charger/discharger 4010duo - 39 - appendix status indication of running channel status status indication status status indication no display no program, can select program to run trick trickle charging status keeps a small current for a while after finishing charging nic...

  • Page 40

    Icharger synchronous balance charger/discharger 4010duo - 40 -  error messages error no. Error messages error description 02xx "input over voltage" the input voltage is too high 03xx "input under voltage" the input voltage is too low 04xx "output over voltage" the output voltage is too high 05xx "l...

  • Page 41

    Icharger synchronous balance charger/discharger 4010duo - 41 - 28xx "number of cells setting appears high" number of cells setting appears high 29xx "balance not needed, remove connection from balance port" balance port error, ni-, pb does not need balance port, but voltage of balance port is detect...