Icom HM-162B Instructions Manual - page 5
⁄3
Display backlight
The function display and keys can be backlit for better visibility
under low light conditions. The backlighting condition can also
be adjusted independently from the transceiver.
➥
While pushing [H/L], rotate [SE-
LECTOR] to adjust the backlight
level.
• “
B
BA
AC
CK
KL
LI
IG
GH
HT
T
” with the back-
light level appears.
• The backlight is adjustable in 7
levels and OFF.
BUSY-
25W
25W
---
---
INT
INT
---CALL
---CALL
LOCAL--DUP
LOCAL--DUP
SCRAM
SCRAM--TAG
--TAG
NORMAL-SCAN
NORMAL-SCAN
BACKLIGHT
BACKLIGHT
-
7
-
OK> COMMERCIAL Appears ⁄4 RX Speaker function q Push [HAIL• RX ] for 1 sec. to enter the RX Speaker mode. • “ ” indicator appears. • The audio output level for the RX speaker can be adjusted when entering this mode. Rotate [SE- LECTOR] then push [ENT]. Or while pushing [HAIL• RX ], rotate [SELECTOR] before tuning OFF this function (within for 1 sec.). w To cancel the RX Speaker mode, repeat step q . • “ ” indicator disappears. RX RX BUSY BUSY- 25W 25W --- --- INT INT ---CALL ---CALL LOCA LOCA RX RX -- UP UP SCRAM SCRAM-- -- TAG TAG NORMAL-SCAN NORMAL-SCAN RX RX - 15 15 4"34.206N 4"34.206N 123"23.236W 123"23.236W - OK> -- -- CALLING CALLING [CH [CH-] ⁄6 Hailer function q Push [HAIL• RX ] to enter the hailer mode. w Push and hold [PTT] and speak at a normal voice level. • “ T TA AL LK K ” appears. • “ W WA AI IT T ” appears while the trans- ceiver side is in use. • To adjust the hailer level, rotate [SELECTOR]. e After speaking, release [PTT]. r To cancel the hailer mode, repeat step q . • Pushing [16•9] also cancels the hailer function. While in the hailer mode, the transceiver functions (transmit and receive) are interrupted. If the transceiver is in transmit condition, the hailer function is not available. BUSY-25W---INT---CALL BUSY-25W---INT---CALL LOCAL--DUP LOCAL--DUP SCRAM--TAG SCRAM--TAG NORMAL-SCAN NORMAL-SCAN HAILER HAILER LISTEN LISTEN 15 15 .236W .236W ___ ____al--1:10--CALLING l--1:10--CALLING ⁄7 Automatic foghorn The automatic foghorn function sounds a horn repeatedly until the function is turned OFF. Four patterns are available for vary- ing conditions. The foghorn outputs from the hailer speaker. To use this func- tion, the hailer speaker must be connected to the transceiver. See the transceiver’s instruction manual for connection details. The audio frequency of the foghorn is selectable in Set mode. q While pushing and holding [H/L], push [HAIL• RX ] to enter auto foghorn mode. w Rotate [SELECTOR] to select the desired foghorn pattern, push [ENT]. • ‘ U UN ND DE ER RW WA AY Y ,’ ‘ S ST TO OP P ,’ ‘ S SA AI IL L ,’ ‘ T TO OW W ’ are available. • Even if [ENT] hasn’t been pushed, the display automatically changes to the next step after 5 sec. of inactivity. e Rotate [SELECTOR] to adjust the foghorn level, push [ENT]. • The foghorn level is adjustable in 30 steps. • Even if [ENT] hasn’t been pushed, the display automati- cally changes to the next step after 5 sec. of inactivity. [VOL] [VOL] BUSY- BUSY- 25W 25W --- --- INT INT ---CALL ---CALL LOCARX LOCARX -- -- UP UP SCRAM SCRAM-- -- TAG TAG NORMAL-SCAN NORMAL-SCAN FOGHORN FOGHORN 15 15 4"34.206N 4"34.206N 123"23.236W 123"23.236W - OK> -- -- CALLING CALLING BUSY- BUSY- 25W 25W --- --- INT INT ---CALL ---CALL LOCARX LOCARX -- -- UP UP SCRAM SCRAM-- -- TAG TAG NORMAL-SCAN NORMAL-SCAN FOG FOG 15 15 4"34.206N 4"34.206N 123"23.236W 123"23.236W - UNDERWAY UNDERWAY -- -- CALLING CALLING [VOL] [VOL] The selected foghorn pattern is displayed. [VOL] [VOL] BUSY- BUSY- 25W 25W --- --- INT INT ---CALL ---CALL LOCA LOCARX RX -- UP UP SCRAM SCRAM-- -- TAG TAG NORMAL-SCAN NORMAL-SCAN ˘UNDERWAY UNDERWAY - STOP STOP 4"34.206N 4"34.206N 123"23.236W 123"23.236W - OK> -- -- CALLING CALLING ⁄5 Intercom operation q Push [LO/DX•IC ] for 1 sec. to activate the Intercom func- tion. w Push and hold [PTT] to talk. • “ I IN NT TE ER RC CO OM M T TA AL LK K ” appears. e Release [PTT] to listen. • “ I IN NT TE ER RC CO OM M L LI IS ST TE EN N ” ap- pears when the transceiver is in talking mode. • To adjust the audio outoput level, push [VOL/SQL] then rotate [SELECTOR VOL ]. r Push [LO/DX•IC ] to cancel the Intercom function. • Pushing [16•9] also cancels the Intercom function. For your reference: In case the Intercom mode is selected with the transceiver while the microphone power is OFF, the microphone power is auto- matically turned ON and the Intercom mode is selected. D D Intercom beep function ➥ Push and hold [LO/DX•IC ] for more than 1 sec. • Emits the Intercom beep while holding. SCR SCR SCR BUSY- BUSY-25W---INT- 25W---INT---CALL --CALL LOCAL--DUP LOCAL--DUP SCRAM SCRAM-- --TAG TAG NORMAL-SCAN NORMAL-SCAN INTERCOM INTERCOM TALK TALK 123"23.236W 123"23.236W --UTC-10:10 --UTC-10:10COMMERCIAL COMMERCIAL BUSY- BUSY-25W---INT- 25W---INT---CALL --CALL LOCAL--DUP LOCAL--DUP SCRAM SCRAM-- --TAG TAG NORMAL-SCAN NORMAL-SCAN INTERCOM INTERCOM LISTEN LISTEN 123"23.236W 123"23.236W --UTC-10:10 --UTC-10:10COMMERCIAL COMMERCIAL AquaQuake helps drain water away from the speaker housing (water that might otherwise muffle the sound coming from the speaker). The HM-162 emits a vibrating noise when this func- tion is being used. This function is availabe depending on the connected transceiver. ➥ While pushing and holding [PTT], turn power ON to clear water away from the HM-162. • A low beep tone sounds while [PTT] is pushed and held to drain water, regardless of volume setting. • The HM-162 never accepts a key operation while the AquaQuake function is activated. ⁄8 AquaQuake water draining function (Available depending on the transceiver) 5