Instruction manual lpd fm handheld transceiver i4008e ic-4008e-2 02.3.23 3:26 pm page 33 (1,1).
I foreword thank you for purchasing the ic-4008e lpd (low power de- vice) fm transceiver. This lpd fm transceiver meets the euro- pean lpd specification (ets 300 220). This transceiver is designed for those who require top-grade quality, performance and outstanding reliability under the most demandi...
Ii ■ water-resistant* construction water-resistant* construction is employed. Can be used any- where, anytime. *meets jis water-protection specification grade 4 . ■ group mode (built-in ctcss: continuous tone coded squelch system ) ctcss encoder/decoder are standard, providing quiet stand-by. Audio ...
Important read all instructions carefully and completely before using the transceiver. Save this instruction manual– this instruction manual contains important operating instructions for the ic- 4008e lpd transceiver. Cautions r warning! Never hold the transceiver so that the an- tenna is very close...
Iv table of contents foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .I–ii supplied accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Ii i...
Panel description 1 1 ‘ ‘ switches, controls, keys and connectors q antenna w [ptt] e [up] r [down] t speaker !0 [vol] o display i [power] u [mode] y mic !1 sp/mic jacks ic-4008e-2 02.3.23 3:26 pm page 6 (1,1).
2 panel description 1 q antenna extend the antenna completely when using the transceiver. • the antenna collapses completely into the transceiver body for car- rying purposes. • the antenna can be adjusted 90 degrees from the regular position when operating the transceiver in a horizontal position. ...
Panel description 1 3 ‘ ‘ function display q transmit indicator appears during ptt on. W busy indicator appears while receiving a signal or when the squelch is open. E key lock indicator appears during key lock function on. R auto power off indicator appears while the auto power off function is on. ...
4 2 accessories d antenna adjust the antenna position as shown at right. Keep the jack cover attached when jacks are not in use to avoid bad contacts. D belt clip attach the belt clip using the supplied screws. Conveniently attaches to your belt. ‘ ‘ accessory attachment ic-4008e-2 02.3.23 3:26 pm p...
‘ ‘ installing batteries in the battery case install 3 r6(aa) size alkaline, dry cell batteries or the bp-202 bat- tery pack as illustrated below. Q remove the battery case cover from the transceiver. W install 3 ×r6(aa) size dry cell, alkaline bat- teries or the bp-202. • be sure to observe the cor...
6 3 battery packs ‘ ‘ battery pack charging the optional bp-202 battery pack includes rechargeable ni-cd batteries and can be charged approx. 300 times. Charge the battery pack before first operating the transceiver or when the battery pack becomes exhausted. If you want to be able to charge the bat...
* 7 3 battery packs ‘ ‘ charging connections d rapid charging with the bc-119l/bc-119+ad-89 q insert the optional ad-89 desktop charger adapter into the charging slot of the bc-119. • the bc-119l comes preinstalled with the ad-89 charging adapter . W insert the battery pack, either by itself or atta...
4 basic operation 8 ‘ ‘ power on ➥ push [ power ] for 1sec. To turn the power on. • the power on indicator and oper- ating channel number appear on the display. ‘ ‘ adjusting the volume q push and hold [ mode ] for 1sec. To open the squelch. • busy indicator appears on the display while the squelch ...
Basic operation 9 4 ‘ ‘ selecting the operating channel push [ up ]/[y] or [ down ]/[z] keys sev- eral times until the desired operating channel number appears on the dis- play. • while pushing and holding [ up ]/[y] or [ down ]/[z] keys, the displayed chan- nel changes continuously until chan- nel ...
5 receive and transmit 10 q push and hold [ mode ] 1sec. To open the squelch. • adjust volume to the desired audio level. (see p. 8) w select a desired operating channel. When a signal is received: • squelch opens and audio is emitted from the speaker. • further adjustment of [ vol ] may be necessar...
11 6 ‘ ‘ setting the group code the ic-4008e is equipped with 38 group codes. Group mode op- eration provides communication with silent standby since you will only receive calls from group members using the same group num- ber. First of all, set the same group code number for all group member’s tran...
12 6 ✔ what is ctcss (continuous tone coded squelch sys- tem) group mode ? Ctcss (continuous tone coded squelch system) group mode allows communication with silent stand by. Only signals containing your group code can open the squelch. This conveniently eliminates unwanted audio and is useful in gro...
13 6 ctcss: continuous tone coded squelch system d ctcss code table ✔ talk range the ic-4008e is designed to maximize performance and im- prove transmission range in the field. However, the single most important factor in transmit range (talk power) is your surrounding environment. These radios are ...
14 7 ring function ‘ ‘ smart-ring the ring function has an answer back feature. This allows you to confirm whether or not a call has reached the receiving party even if the operator is temporarily away from the transceiver. Q set the same group channel number for all of your group transceivers. (see...
15 other functions 8 ‘ ‘ initial set mode initial set mode is accessed at power on and allows you to set sel- dom changed settings. In this way you can “customize” transceiver operations to suit your preferences and operating style. D auto power off this function sets the transceiver to auto- matica...
16 8 other functions d ptt hold function this function frees you from having to constantly push [ptt] during conversation. Q while pushing [ptt], push [power] on to toggle the function on or off. W “ ” appears on the display when the “ptt hold” function is activated. E once [ptt] is pushed, you need...
Other functions 8 17 ‘ ‘ ats (automatic transponder system) this allows you to confirm whether or not a call has reached the re- ceiving party even if the operator is temporarily away from the transceiver. No “ring” tone is emitted with this function. ➥ push [mode], while [ptt] is on to turn the fun...
18 8 other functions ‘ ‘ lcd backlight ➥ automatically turns on for 5 sec. When you push any key, ex- cept [ptt]. ‘ ‘ auto power save ➥ the power save function reduces the current drain to conserve battery power. - the function automatically turns on when no operation is per- formed or no signal is ...
Other functions 8 19 ‘ ‘ optional hm-75a functions the optional hm-75a allows you to remotely select operating chan- nels, open the squelch, etc. The switches on the hm-75a function as follows. Caution: when connecting the hm-75a to the transceiver, make sure that power to the transceiver is turned ...
20 9 specifications general • frequency coverage : 433.075–434.775 mhz • mode : f3e (fm) • no. Of operating ch. : 69 (simplex) • frequency stability : ±5.7 ppm; ±2.5 khz • frequency resolution : 25 khz • power supply requirement: 4.5 v (r6 × 3) or bp-202 • current drain : less than 140 ma • operatin...
Options 10 21 d battery packs bp-202 ni-cd battery pack 3.6v/ 700 mah rapid charge battery pack. (p. 6–7) d chargers bc-119 desktop charger + ad-89 desktop charger adapter rapidly charge battery packs in 1 to 1.5 hrs. An ac adapter is packed with the bc-119. The ad-89 must be used with the bc-119 fo...
22 11 memo operating channel number group code number ‘ ‘ channel number and group number use this page to record your group operating channel number (see p. 9) and group channel number (p. 11) for your reference. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 ch freq.(mhz) 433.075 433....
23 11 memo ic-4008e-2 02.3.23 3:26 pm page 28 (1,1).
24 11 memo ic-4008e-2 02.3.23 3:26 pm page 29 (1,1).
25 12 ce about ce ce versions of the ic-4008e which display the “ce” symbol on the serial number seal, comply with the essential requirements of the european radio and telecommunication terminal direc- tive 1999/5/ec. This warning symbol indicates that this equipment operates in non-harmonised frequ...
26 12 ce declaration of conformity we icom inc. Japan 1-1-32, kamiminami, hirano-ku osaka 547-0003, japan kind of equipment: lpd fm transceiver this compliance is based on conformity with the following harmonized standards, specifications or documents: i) prets 300 683 january 1997 (emc product stan...
Instruction manual 1-1-32 kamiminami, hirano-ku, osaka 547-0003 japan a-5460h -1eu-w printed in japan © 1997 icom inc. Count on us! O ger o aut o gbr o irl n fra n ned o bel o lux n esp n por n ita n gre n swe o den o fin ic-4008e-2 02.3.23 3:26 pm page 32 (1,1).