1. DL manuals
  2. Icom
  3. Transceiver
  4. IC-9100
  5. Instruction Manual

Icom IC-9100 Instruction Manual

Other manuals for IC-9100: Instruction Manual, Overview, Service Manual
Manual is about: HF/VHF/UHF Transceiver

Summary of IC-9100

  • Page 1

    Hf/vhf/uhf transceiver i9100 instruction manual.

  • Page 2

    I foreword thank you for making the ic-9100 your radio of choice. We hope you agree with icom’s philosophy of “technology first.” many hours of research and devel- opment went into the design of your ic-9100. Features m the ic-9100 fully covers hf to 1200 mhz* 1 multi- band in one transceiver m inde...

  • Page 3

    Precautions r danger high rf voltage! Never attach an antenna or internal antenna connector during transmission. This may result in an electrical shock or burn. R warning! Never operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against co...

  • Page 4

    Iii d about the d-star system in the original d-star (digital smart technologies for amateur radio) plan, jarl envisioned a system of repeaters grouped together into zones. A zone would be a group of up to 4 repeaters, linked by 10 ghz “backbone” microwave link repeaters. Each individual repeater wo...

  • Page 5

    Iv 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 area 1 zone a repeater 1 area 2 repeater 2 area 3 repeater 3 area 4 repeater 4 zone b area 7 repeater 6 area 6 repeater 7 area 8 repeater 8 area 5 repeater 5 internet internet (gateway) (gateway) area: the area is the communication range that ...

  • Page 6

    V table of contents foreword .............................................................. I important ............................................................... I explicit definitions ............................................ I supplied accessories....................................... I ...

  • Page 7

    Table of contents vi 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n electronic keyer functions ............................... 50 d memory keyer menu construction ............... 50 d memory keyer send menu........................... 51 d editing a memory keyer ................................

  • Page 8

    Vii table of contents n calling a specific station ................................ 103 d confirming the setting ............................... 105 d settings for “ur” and “r2,” depending on the communication form .................................. 105 n simplex operation using the vfo ...............

  • Page 9

    Viii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 table of contents 12 satellite operation ......................... 153 – 157 n satellite communications outline ................... 153 n satellite notes ................................................ 153 n selecting the satellite mode ......

  • Page 10: Panel Description

    1 1 panel description q power switch [power] (p. 31) ± push to turn on the transceiver power. S&irstconlrmthe$#powersourceisturned/. ± hold down for 1 second to turn off the power. W transmit switch [transmit] (p. 46) push to select transmit or receive. S7hile transmitting the -!). "ands4828 indica ...

  • Page 11

    2 1 panel description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 o -!)."!.$2&'!).#/.42/, squelch control [rf/sql] outercontrolp rotate to adjust the rf gain and squelch threshold level for the main band. The squelch removes noise output to the speaker when no signal is received. (closed c...

  • Page 12

    !3 menu switch [menu] (p. 19) ± push to change the set of functions assigned to switches ([f-1] to [f-5]). S4oggles the function display menu between - (menu 1), m2 (menu 2), m3 (menu 3), d1 and d2. ± hold down for 1 second to enter the set mode. Push to return to the previous screen display. !4 noi...

  • Page 13

    @2 electronic cw keyer speed control [key speed] (p. 49) -ode#7 rotate to adjust the keying speed of the internal electronic cw keyer to between 6 wpm (minimum) and 48 wpm (maximum). Fast slow @3 02%!-0s!44%.5!4/237)4#(;0!-0s!44= preamp switch /peration (p. 71) &requencyband(&-(z ± push to select on...

  • Page 14

    @9 mode switches push to select your desired operating mode. (p. 43) s4hebuiltinspeechsynthesizerannouncestheselected mode when the “speech [mode] sw” item is set to “on” in the set mode. (p. 164) ;33"= (p. 47) ± push to alternately select the usb or lsb modes. Sh53"vorh,3"vappears ± in the ssb mode...

  • Page 15

    #2 6&/3%,%#437)4#(;!"= (pp. 32, 34) ± push to select either vfo a or vfo b. ± hold down for 1 second to equalize the undis- played vfo settings to that of the displayed vfo. #3 split switch [split] (p. 82) ± push to turn the split function on or off. Sh30,)4vappearswhenthesplitfunctionis/. S4he spli...

  • Page 16

    #8 vfo/memory switch [vfo/memo] ± push to switch between the vfo and memory modes. (pp. 34, 139) ± hold down for 1 second to copy the memory con- tents to the displayed vfo on the main band. (p. 142) #9 memo pad-write switch [mp-w] (p. 144) push to write the displayed data into a memo pad. S4hemostr...

  • Page 17

    $4 0"4#,%!237)4#(;0"4#,2= (p. 75) -ode33"#72449!- ± push to display the filter passband width and shifting value for 1 second on the function dis- play. ± hold down for 1 second to reset the pbt set- tings. $5 0!33"!.$45.).'#/.42/,3;47).0"4= (p. 75) -ode33"#72449!- adjusts the receiver’s if filter p...

  • Page 18

    %1 main dial (pp. 37, 161) rotate to change the displayed frequency, select the set mode settings, etc. When the sub band setting mode is on, rotat- ing [main dial] changes the sub band fre- quency. (p. 33) %2 clear switch [clear] (pp. 69, 81) hold down for 1 second* to clear the rit/ ∂ tx shift fre...

  • Page 19: 2Earpanel

    10 1 panel description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 2earpanel q antenna connector 1 [ant1] w antenna connector 2 [ant2] (pp. 24, 25, 158) connect a 50 ø antenna with a pl-259 plug con- nector for the hf/50 mhz frequency band. When using an optional ah-4 hf /50 mh z auto - ...

  • Page 20

    O ground terminal [gnd] (p. 22) connect this terminal to a ground to prevent electri- cal shocks, tvi, bci and other problems. !0 tuner control socket [tuner] (p. 29) connect the control cable from an optional ah-4 hf/ 50 mh z automatic antenna tuner . !1 data1 jack [data1] (pp. 26, 168) ± connect a...

  • Page 21

    12 1 panel description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 !8 53"5niversal3erial"us 0/24;53"= using a usb cable, connect a pc to do the follow- ing: - input modulation (p. 167) - remotely control the transceiver using ci-v com- mands (p. 183) - send the received audio to the pc - s...

  • Page 22

    13 1 panel description n rear panel (continued) d !##socketinformation s!##socket acc pin no. Name description specifications 1 2 3 4 8 7 6 5 9 10 11 12 13 rear panel view color refers to the cable strands of the supplied cable. Q brown w red e orange r yellow t green y blue u purple i o !0 !1 !2 !3...

  • Page 23

    14 1 panel description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d $!4!Socketinformation data2 pin no. Name description specifications q w e r t y rear panel view 1 data in input terminal for data transmit. ( 1200 bps: afsk/ 9600 bps: g3ruh, gmsk) input level (1200 bps) input level (9600...

  • Page 24: ,#$Display

    N ,#$display !2 !0 q t w q r w e y y o o !1 u i !0 u i 15 1 panel description q frequency readouts displays the operating frequency. S7henthequicktuningiconh z ” is displayed, the fre- quency changes in pre-set khz or 1 mhz quick tuning steps. (p. 38) s7henthequicktuningiconh z ” is not displayed, t...

  • Page 25

    16 1 panel description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 !5 !3 !4 !5 @0 !6 !8 !9 !4 !3 !7 !3 tone squelch icons -ode&- ± “t” appears when the repeater tone function is on. (p. 65) ± “tsql” appears when the tone squelch function is on. (p. 62) ± “dtcs” appears when the dtcs code s...

  • Page 26

    17 1 panel description n lcd display (continued) @2 @1 @3 @4 @6 @5 @7 #1 @4 @3 @2 @9 @8 #0 @1 split icon (p. 82) appears when the split function is turned on. @2 dsp filter icon (p. 73) displays the selected if filter. @3 agc icons (p. 72) displays the selected agc time constant. Sh vfor!'#fasth vfo...

  • Page 27

    18 1 panel description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 #4 #5 #5 #3 #2 $1 #8 #7 #6 $0 #9 #3#2 #4 #7 #6 $1 #8 #9 #2 noise reduction icon (p. 77) appears when the noise reduction function is turned on. #3 ./)3%",!.+%2)#/. (p. 76) appears when the noise blanker function is turned o...

  • Page 28: &unctiondisplay

    19 1 panel description n &unctiondisplay push [menu] to toggle the function display menu. S4hesetoffunctionsassignedtothefunctionswitches change according to the selected menu and operat- ing mode. S)nthe$6mode- menu 3) display can be selected after selecting menu 2. S)nthe$2modethe$and$displayscanb...

  • Page 29

    20 1 panel description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d &unctionkeyson--enu display !'#+%9;!'#=& (p. 72) ± push to select the time constant of the agc circuit. ± hold down for 1 second to display the “agc” screen. $50,%8+%9;$50=& (p. 65) ± push to select the duplex direction, ...

  • Page 30

    21 1 panel description n function display (continued) d &unctionkeyson--enu display -ode$6 #!,,3)'.+%9;#3=& (p. 85) push to display the “cs” screen. S4hecurrentcallsignfor$6operationappears #!,,2%#/2$+%9;#$=& (p. 95) push to display the “cd” screen. S4hecallrecordchannel appears. (rx01 to rx20) 2#3+...

  • Page 31: Installation and Connections

    2 22 installation and connections 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 3electingalocation select a location for the transceiver that allows ade- quate air circulation, free from extreme heat, cold, or vibrations, and away from tv sets, tv antenna ele- ments, radios and other elect...

  • Page 32: !ntennaconnection

    23 2 installation and connections pl-259 connector installation example type-n connector installation example slide the coupling ring down. Strip the cable jacket and tin the shield. Slide the connector body on and solder it. Screw the coupling ring onto the connec- tor body. Strip the cable as show...

  • Page 33: 2Equiredconnections

    24 2 installation and connections 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 2equiredconnections d 2earpanel + _ dc power supply (p. 27) ;-(z!.4= (p. 158) ;-(z!.4= (p. 158) ps-126 use the heaviest possible gauge wire or strap and make the connection as short as possible. Grounding preve...

  • Page 34: !dvancedconnections

    D 2earpanel 25 2 installation and connections n !Dvancedconnections d &rontpanel headphones mic the afsk modulation signal can also be input to [mic]. (p. 171) ah-4 (option) (p. 29) ah-2b (option) or long wire with preamp (p. 71) (144 mhz and 430 mhz) 144 mhz : ag-25 (option) 430 mhz : ag-35 (option...

  • Page 35: %xternalkeypadconnections

    26 2 installation and connections 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n %xternalkeypadconnections to pin e to pin y 1.5 k ø ±5% 1.5 k ø ±5% 2.2 k ø ±5% 4.7 k ø ±5% s1 (m1) s2 (m2) s3 (m3) s4 (m4) external keypad 1 2 3 4 5 6 7 8 (front view) [mic] external keypad connect an external...

  • Page 36: 0Owersupplyconnections

    N 0owersupplyconnections when operating the transceiver with ac power, use a power supply with 13.8 v dc output and a capacity of at least 24 amperes. Refer to the diagrams below. #!54)/. Before connecting the dc power cable, check the following important items. Make sure: s4he;0/7%2=switchis/&& s/u...

  • Page 37: ,inearamplilerconnections

    28 2 installation and connections 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n ,inearamplilerconnections d #onnectingthe)#0707%52/ exciter 1 1&2 remote control cable (supplied with the ic-pw1/pw1euro) acc cable (supplied with the ic-pw1/pw1euro) to an antenna [acc1] [remote] [ant] ic-pw1/...

  • Page 38

    29 2 installation and connections n linear amplifier connections (continued) d #onnectinganon)comlinearampliler r warning! S3etthetransceiveroutputpowerandlinearampliler!,#outputlevelafterreferringtothelinearamplilerin - struction manual. S4he!,#inputlevelmustbeintherange6ton64hetransceiverdoesnotac...

  • Page 39: -Icrophones

    30 2 installation and connections 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n -icrophoneconnectorinformation (front panel view) y gnd (ptt ground) t ptt r main band’s squelch switch q microphone input w +8 v dc output e frequency up/down i main band’s af output (varies with [af]) gnd (mi...

  • Page 40: "eforelrstapplyingpower

    [rf/sql] : 12 o’clock [mic gain] : 12 o’clock [nr] : max. Ccw [cw pitch] : 12 o’clock [notch] : 12 o’clock [rf power] : max. Cw ;+%930%%$= : 10–12 o’clock [af] : max. Ccw n "eforelrstapplyingpower before turning on your transceiver for the first time, make sure all connections required for your syst...

  • Page 41: -!).And35""ands

    32 3 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 32 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n -!).And35""ands the ic-9100 can operate on the hf/50 mhz, 144 mhz, 430 mhz and 1200 mhz* frequency bands. These fre- quency bands can be assigned to the main and sub ...

  • Page 42

    33 3 basic operation d 4he35"$ialfunction the [sub dial] control’s tuning band and frequency steps differ, depending on the combination of the sub dial function and sub band setting mode, and the sta- tus of the quick tuning function. ± push [sub dial] to turn the sub dial function on or off. Sh ” a...

  • Page 43: 6&/description

    34 3 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 6&/description 4he)#hastwo6&/sh!Vandh"vforeach-!). And sub bands, and are convenient for quickly select- ing two frequencies orsplitfrequencyoperation9ou can use either vfo to call up a frequency and operat- ing mode. Vfo i...

  • Page 44: 3Electingafrequencyband

    35 3 basic operation "!.$ register 1 register 2 register 3 1.8 mhz* 1 1.900000 mhz cw 1.910000 mhz cw 1.915000 mhz cw 3.5 mhz* 1 3.550000 mhz lsb 3.560000 mhz lsb 3.580000 mhz lsb 7 mhz 7.050000 mhz lsb 7.060000 mhz lsb 7.020000 mhz cw 10 mhz* 1 10.120000 mhz cw 10.130000 mhz cw 10.140000 mhz cw 14 ...

  • Page 45

    36 3 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 &requencyband(&-(z q hold down [band](main/sub) for 1 second one or more times until a hf/50 mhz frequency band is displayed. W 0ushabandkey;=to;=or;'%.%s= s4hepreviouslyselectedfrequencyandoperatingmode are called up as the ...

  • Page 46: &requencysetting

    37 3 basic operation n &requencysetting 9oucanselectthetransceiversfrequencybyusing [main dial], or you can enter it using the keypad. D 4uningwith;-!).$)!,= q select the desired frequency band. S(old down ;"!.$=-!).35" for second one or more times until the desired frequency band is dis- played. S0...

  • Page 47

    38 3 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d 1uick4uningfunction the operating frequency can be changed in ‘khz’ or ‘mhz’ steps for quick tuning. Select the desired tuning step in each operating fre- quency band and mode. Q push [ts] to select the ‘khz’ or ‘mhz’ quick...

  • Page 48

    39 3 basic operation n frequency setting (continued) d 3electing(zstep 9oucanchangethefrequencyin(zstepsforfine tuning. Q push [ts] to turn off the quick tuning function. W hold down [ts] for 1 second to turn the 1 hz tuning step on or off. ./4% s7hen2)4andor ∂ tx are used, they also tune in 1 hz tu...

  • Page 49

    40 3 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d !Boutthe-(zfrequencybandoperationonly53!Version operation on the 5 mhz band is allowed on 5 discrete frequencies and must adhere to the following: s4he53"mode s-aximumofwatts%20 (effective radiated power) sk(zbandwidth it’s...

  • Page 50

    41 3 basic operation n frequency setting (continued) d "andedgewarningbeep 9oucanhearabeeptonewhenyoutuneintoorout of an amateur band’s frequency range. A regular beep sounds when you tune into a range, and an lower tone error beep sounds when you tune out of a range. Q hold down [menu] for 1 second...

  • Page 51

    42 3 basic operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d 0rogrammingtheuserbandedge 7henh/.5ser vorh/.5ser 48visselectedin the “band edge beep” item, the “user band edge” item appears in the set mode. A total of 30 band edge frequencies can be pro- grammed in the “user band edge”...

  • Page 52: /peratingmodeselection

    43 3 basic operation n /peratingmodeselection the usable operating modes in the ic-9100 are listed to the right. 9oucanselectthedesiredoperatingmodebypush - ing the mode switch. See the diagram to the right for the order of selection. 9ou can mute the microphone signals when the data mode is selecte...

  • Page 53

    N 3quelchandreceive2& sensitivity adjusts the rf gain and squelch threshold level. The squelch removes noise output to the speaker when no signal is received (closed squelch). S4hesquelchisparticularlyeffectivefor!-and&-butcan also be used in other modes. S4hetooclockpositionisrecommendedfor the mos...

  • Page 54: 6Olumesetting

    45 3 basic operation n 6olumesetting ± rotate the [af] control clockwise to increase the audio output level, counterclockwise to decrease it. Increases decreases n 6oicesynthesizeroperation the ic-9100 has a built-in voice synthesizer to an- nounce the operating frequency, mode and s-meter level in ...

  • Page 55: "asictransmitoperation

    N "asictransmitoperation "eforetransmittingmonitortheoperatingfre - quencytomakesuretransmittingwontcause interferencetootherstationsonthesamefre - quency)tsgoodamateurpracticetolistenlrst andthenevenifnothingisheardaskh)sthefre - quencyinusevonceortwicebeforeyoubegin operatingonthatfrequency d 4ran...

  • Page 56: Receive And Transmit

    4 47 receive and transmit n /perating33" q select the desired frequency band. (p. 35) w push [ssb] to select the lsb or usb mode. S7henoperatingabove-(z53"isselectedlrst when operating below 10 mhz, lsb is selected first. S!Fter53"or,3"isselectedholddown;33"=for second to select the data mode, if ne...

  • Page 57: /perating#7

    48 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n /perating#7 q select the desired frequency band. (p. 35) w 0ush;#72449=toselect#7 s!Fterthe#7modeisselectedholddown;#72449= for 1 second to toggle between cw and cw-r modes, if necessary. E rotate [main dial] to tune a...

  • Page 58

    49 4 receive and transmit bfo cw-r mode (usb side) bfo desired signal cw mode (lsb side) interference desired signal interference n operating cw (continued) d about the cw reverse mode the cw reverse mode receives signals with a reverse side cw carrier point similar to voice lsb and usb modes. Use w...

  • Page 59: %lectronickeyerfunctions

    50 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n %lectronickeyerfunctions 9ou can access a number of convenient functions of the built-in electronic keyer in the memory keyer menu. Q in the cw mode, push [menu] to display the “m1” screen (menu 1). W 0ush;+%9=& todisp...

  • Page 60

    51 4 receive and transmit n electronic keyer functions (continued) d -emorykeyersendmenu pre-set characters can be sent using the keyer send menu. Contents of the memory keyer are set in the edit menu. S4ransmitting q in the cw mode, push [menu] to display the “m1” screen (menu 1). W 0ush;+%9=& todi...

  • Page 61

    52 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d %ditingamemorykeyer the contents of the memory keyer memories can be set using the memory keyer edit menu. The memory keyer can memorize and re-transmit 4 cw key codes for often-used cw sentences, contest numbers or a ...

  • Page 62

    53 4 receive and transmit n electronic keyer functions (continued) d #ontestnumber3etmode this mode is used to set the contest number, count up trigger and present number. S3ettingcontents q in the cw mode, push [menu] to display the “m1” screen (menu 1). W 0ush;+%9=& todisplaytheh+%9vscreen-em - or...

  • Page 63

    54 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d keyer set mode this set mode is used to set the cw sidetone, mem- ory keyer repeat time, dash weight, paddle specifica- tions, keyer type, etc. S3ettingcontents q in the cw mode, push [menu] to display the “m1” screen ...

  • Page 64

    55 4 receive and transmit n electronic keyer functions d keyer set mode (continued) 0addle0olarity 7. $efault./2-!, set the paddle polarity. S.Ormalorreversepolaritycanbeselected +eyer4ype 8. $efault%,%#+%9 3electthekeyertypefor;%,%#+%9=connectoron the front panel. S3traight key "5'+%9 or %,%#+%9 ca...

  • Page 65: /perating2449&3+

    56 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n /perating2449&3+ 7henusingyour2449terminalor4.#consultthe manual that comes with the equipment. Q select the desired frequency band. (p. 35) w 0ush;#72449= once or twice toselectthe2449 mode. S!Fterthe2449modeisselecte...

  • Page 66: 2449Functions

    57 4 receive and transmit n 2449functions 4he2449menuhasanumberofconvenientfunctions for2449operation q 0ush;#72449= once or twice toselectthe2449 mode. S!Fterthe2449modeisselectedholddown;#72449= for 1 second to toggle between normal and reverse modes, if needed. W push [menu] to display the “m1” s...

  • Page 67

    58 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d about rtty reverse mode received characters are occasionally garbled when the mark and space signals are reversed. This rever- sal can be caused by incorrect tnc connections, set- ting or commands. 4oreceivereversed244...

  • Page 68

    59 4 receive and transmit n 2449functions#ontinued d rtty decoder 4he transceiver has an 2449 decoder for "audot (mark freq.: 2125 hz, shift freq.: 170 hz, 45 bps). An external terminal unit (tu) or terminal node con- nector (tnc) is not necessary for receiving a baudot signal. Q )nthe2449modepush;-...

  • Page 69

    60 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d rtty set mode 4he24493etmodeisusedtosetthemarkandshift frequencies, keying type, decode usos function, 2449decodernewlinecodeandthenumberofde - code screen display lines. S3ettingcontents q )nthe2449modep ush [menu] to...

  • Page 70: /perating!-&-

    61 4 receive and transmit n /perating!-&- q select the desired frequency band. (p. 35) w push [am/fm] to select the am or fm mode. S!Fter!-or&-isselectedholddown;!-&-=for second to select the data mode, if needed. E rotate [main dial] to tune a desired signal. S4he3meterdisplaysthereceivedsignalstre...

  • Page 71: 4Onesquelchoperation

    62 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 4onesquelchoperation the tone squelch opens only when you receive a sig- nal containing a matching subaudible tone 9ou can silently wait for calls from others using the same tone. Q push [am/fm] once or twice to select...

  • Page 72: $4#3Operation

    63 4 receive and transmit n $4#3operation the dtcs function is another method of communica- tions using selective calling. Only received signals hav- ing a matching 3-digit code will open the squelch. Q push [am/fm] once or twice to select the fm mode. W push [menu] to display the “m1” screen (menu ...

  • Page 73

    64 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 to search for a repeater’s sub-audible tone frequency, a tone scan is available. By monitoring a repeater signal with a tone squelch or dtcs, you can determine the tone frequency neces- sary to open the repeater or the s...

  • Page 74: 2Epeateroperation

    65 4 receive and transmit n 2epeateroperation a repeater receives transmitted signals and re-trans- mits them on a different frequency. When using a re- peater, the transmit frequency is shifted from the re- ceive frequency by a frequency offset. A repeater can be accessed using the duplex opera- ti...

  • Page 75

    66 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d /netouchrepeaterfunction this function allows you to set the repeater operation by holding down one switch. First, set the frequency offset as well as the repeater access tone frequency (p. 163). Q select the desired f...

  • Page 76

    67 4 receive and transmit repeater operation (continued) d 3ettingthe!Uto2epeaterranges 53!And+oreaversionsonly the transceiver has three auto repeater ranges that can be used for each frequency band. And you can set the desired auto repeater ranges by programming the lower and higher edge frequenci...

  • Page 77

    68 4 receive and transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d 4urning/.The!Uto2epeaterfunction 53!And+oreaversionsonly when the operating frequency falls within the repeater output frequency range, the auto repeater function automatically sets the repeater settings (duplex on/ of...

  • Page 78: Functions For Receive

    5 69 functions for receive n !Operation -ode&-$6 afc stands for automatic frequency control. The afc function tunes the displayed frequency automatically when an off-center frequency is received. Q push [am/fm] or ;$6s$2= once or twice to select the fm or dv mode. W push [menu] to display the “m1” s...

  • Page 79: 3Implebandscope

    70 5 functions for receive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 3implebandscope the band scope function allows you to visually check the location and strength of signals around a specified frequency. The ic-9100’s band scope function can be used in any operating mode and any frequ...

  • Page 80: 0Reampliler

    71 5 functions for receive n 0reampliler the preamplifier amplifies weak signals in the receiver front end, to improve the s/n ratio and sensitivity. Turn this function on when receiving weak signals. The ag-25, ag-35 or ag-1200* 1 preamplifier unit is required for 144, 430 or 1200 mhz* 2 frequency ...

  • Page 81: !'#function

    72 5 functions for receive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n !'#function the agc (auto gain control) controls receiver gain to produce a constant audio output level, even when the received signal strength varies greatly. The transceiver has 3 pre-set agc time constants: fast, m...

  • Page 82: )&llterselection

    73 5 functions for receive n )&llterselection the transceiver has 3 passband width if filters for each mode. The filter selection is automatically memorized in each mode. The pbt shift frequencies are automatically memo- rized in each filter. D )&llterselection q select the desired mode. W push [fil...

  • Page 83

    74 5 functions for receive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d st)&llterselection -ode33"#72449!- the ic-9100 has a 15 khz filter passband width at the 1st if frequency. The 1st if filters reduce interference from strong nearby signals. If the optional fl-430 1 st if filter (6 k ...

  • Page 84: 4Win0"4Operation

    75 5 functions for receive n 4win0"4operation -ode33"#72449!- to reject interference, pbt (passband tuning) elec- tronically narrows the if passband width by shifting the if frequency slightly outside of the if filter passband. The ic-9100 uses dsp for the pbt function. Moving both [twin-pbt] contro...

  • Page 85: .Oise"lanker

    76 5 functions for receive 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n .Oise"lanker -ode33"#72449!- the noise blanker eliminates pulse-type noise such as noise from car ignitions. ± push [nb] to turn the noise blanker function on or off. S “nb” is displayed when the noise blanker is on. ...

  • Page 86: .Oise2Eduction

    77 5 functions for receive n .Oise2eduction the noise reduction function reduces random noise components and enhances audio signals which are buried in noise. The received signals are converted to digital signals and then the audio signals are sepa- rated from the noise. Q push [nr] to turn on the n...

  • Page 87: Functions For Transmit

    6 78 functions for transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 6/8function -ode33"!-&-$6 the vox (voice-operated transmission) function switches the transceiver between transmit and receive with your voice. This function provides hands-free op- eration. D 5singthe6/8function q s...

  • Page 88: "reakinfunction

    79 6 functions for transmit n "reakinfunction -ode#7 the break-in function is used in the cw mode to auto- matically toggle the transceiver between transmit and receive when keying. The ic-9100 is capable of full break-in or semi break-in. D 3emi"reakinoperation during semi break-in operation, the t...

  • Page 89: 3Peechcompressor

    80 6 functions for transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 3peechcompressor -ode33" the speech compressor function increases average rf output power, improving signal strength and read- ability. Q push [ssb] to select the usb or lsb mode. W adjust the [mic gain] control so t...

  • Page 90: 48Function

    81 6 functions for transmit n ∂ 48function the ∂ tx function shifts the transmit frequency up to ±9.99 khz in 10 hz steps* without changing the re- ceive frequency. * the [rit/ ∂ tx] control tunes in 1 hz steps when the operating frequency readout is set to the 1 hz step readout. However, the 1 hz d...

  • Page 91: 3Plitfrequencyoperation

    82 6 functions for transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 3plitfrequencyoperation split frequency operation allows you to transmit and receive on two different frequencies. Split frequency operation is performed using frequencies in vfo a and vfo b. S4he3plitfrequencyoperat...

  • Page 92: 1Uick3Plitfunction

    83 6 functions for transmit n 1uick3plitfunction when you hold down [split] for 1 second, the split frequency operation is turned on. The undisplayed vfo is automatically changed according to the plus/ minus frequency shift programmed in the set mode. Or the vfos are equalized when 0 khz (default se...

  • Page 93: -Easuring372

    84 6 functions for transmit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n -easuring372 "and(&-(z the ic-9100 has a built-in circuit for measuring an- tenna swr— no external equipment or special adjust- ments are necessary. The ic-9100 can measure swr two ways— spot mea- surement and plot m...

  • Page 94: Dv Mode Programming

    7 85 dv mode programming the optional ut-121 is required for dv mode opera- tion. N #allsignprogramming &ourtypesofcallsignsareusedh-9vyourowncall sign) “ur” (destination call sign, whether it is an indi- vidual or a repeater.) “r1” (your access/area repeater call sign) and “r2” (a destination or ga...

  • Page 95

    86 7 dv mode programming 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d h52v$estinationcallsign programming a destination call sign must be programmed to a spe- cific individual station or a repeater, for both digital voice and low-speed data communications. Q push [dv s dr] to select the d...

  • Page 96

    87 7 dv mode programming the access/area and link/gateway repeater call signs must be programmed in “r1” and “r2.” other repeater call signs can be stored in the “rp-l” screen (repeater list) (p. 88). Q push [dv s dr] to select the dv mode. W push [menu] one or more times to display the “m3” screen ...

  • Page 97: 2Epeaterlist

    88 7 dv mode programming 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 2epeaterlist 9oucanstorerepeaterinformationforquickandsimple communication in up to 500 repeater memory chan- nels (repeater list) in up to 10 groups. Programming the repeater list is required for dr mode operation. The...

  • Page 98: 2Epeaterlistprogramming

    89 7 dv mode programming n 2epeaterlistprogramming .Ewrepeaterlist 1. Programming q push [dv s dr] to select the dv mode. W push [menu] one or more times to display the “m3” screen (menu 3). S)nthe$2modep ush [menu] once or twice to select the “d1” screen. Cs c d r > c s u r dset m3 when the “m3” sc...

  • Page 99

    90 7 dv mode programming 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 'atewayr 4. Epeatercallsignprogramming when the repeater that was programmed in the pre- vious item has its own gateway capability, skip this setting and go to the next item. If the programmed repeater uses a different ga...

  • Page 100: %ditingarepeaterlist

    91 7 dv mode programming $uplexdirectionsetting$50 8. This content appears when “ 9%3 ” is selected in “r1 use” as described in ‘access repeater setting (r1 use)’ on page 90. #1 push [ z ](f-2) to display the “dup” item (duplex di- rection setting). S4heduplexdirectionsettingscreenisdisplayed rp–l d...

  • Page 101: #learingarepeaterlist

    92 7 dv mode programming 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n #learingarepeaterlist contents of programmed list can be cleared (erased). Q push [dv s dr] to select the dv mode. W push [menu] one or more times to display the “m3” screen (menu 3). Cs c d r > c s u r dset m3 e push [...

  • Page 102: Dv Mode Operation

    8 93 dv mode operation n $igitalmodeoperation the ic-9100 can be operated in the digital voice mode, including low-speed data operation, for both transmit and receive. It can also be connected to a gps re- ceiver* to transmit/receive position data. * compatible with an rs-232 output/nmea format/ 480...

  • Page 103: 2Eceivinga$34!2Repeater

    94 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 2eceivinga$34!2repeater when the ic-9100 receives a signal from a d-star repeater, it receives four call signs: the calling station’s call sign, the called station’s call sign, the r1 repeater call sign (the repeater that...

  • Page 104: 2Eceivedcallsigns

    95 8 dv mode operation n 2eceivedcallsigns when a call is received in the dv mode, the calling sta- tion and repeater call signs being used can be stored in the received call record. The stored call signs can be displayed in the following manner. Up to 20 calls can be stored. D $esiredcallrecorddisp...

  • Page 105

    96 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d /netouchreplyusingthecallrecord the calling station’s call sign, which is stored in the call record, can be used to quickly and easily reply. S&irstsetyourowncallsign-9 p s!Fterreceivingacall q push [menu] one or more tim...

  • Page 106: #opyingthecallsign

    97 8 dv mode operation n #opyingthecallsign d #opyingthecallsignmemorycontents the memorized ur call sign can be copied into an- other call sign memory. ./4% first, make sure that the “edit record” item is set to “auto” or “select” in the dv set mode. (p. 119) q push [dv s dr] to select the dv mode....

  • Page 107

    98 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 this is a way to copy the call record data (“caller,” “rxrpt1” and “rxrpt2”) into call sign memory “ur” and a repeater all at the same time, or individually. Q push [dv s dr] to select the dv mode. W push [menu] one or more...

  • Page 108

    99 8 dv mode operation dr (d-star repeater) mode is used for d-star repeater operation. In this mode, you can select the pre-programmed repeaters and ur call sign by using [main dial]. S$2modeoperationmowchart s2epeatersettingscanbestoredintoarepeatermemory channel (repeater list). N $2$34!22epeater...

  • Page 109

    100 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 s!Ccessrepeaterscan ’ stargetsetting 9oucanselectthedesiredrepeatersasascantarget , for faster selection and scanning. Non-selected repeaters are skipped during scanning. S when a repeater is specified as a non-scan target...

  • Page 110: #alling#1

    101 8 dv mode operation n #alling#1 &irstprograma-9callsigninstep q . Next program the repeater list (p. 89). After that, follow this guide to access a d-star repeater. The optional cs-9100* cloning software is helpful for programming call signs and programming the repeater list. *cloning cable is r...

  • Page 111

    102 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 -akinga:one#1'ateway#1call ./4% the settings are the same between zone cq and gateway cq call. Cs c d r > c s u r dset d1 grp3 u r : i k o m a − 4 3 repeater selection screen appear [transmit] [ [main dial] main band tx/rx...

  • Page 112: #allingaspecilcstation

    103 8 dv mode operation n #allingaspecilcstation this section describes how to call a specific station using the dr mode. When the link repeater (r2) is set to “gw,” the des- ignated gateway repeater is automatically set as the link repeater, and you can make a call to a specific station through the...

  • Page 113

    104 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 link repeater in the same zone cs c d r > c s u r dset d1 r 2 : i k o m a − 4 3 gateway repeater “gw” cs c d r > c s u r dset d1 r 2 : g w -aking a call to an individual station through a linkrepeaterinthesamezone:onecall ...

  • Page 114

    105 8 dv mode operation n calling a specific station (continued) d #onlrmingthesetting q in the dr mode, push [menu] one or more times to display the “d1” screen. W push [cs](f-1) to display the “cs” screen (call sign). E push [ z ](f-1) one or more times to sequentially displaytheh52vh2vh2vorh-9vto...

  • Page 115: 3Implexoperationusingthe6&/

    106 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 s #alling#1 ur my my ja3yua ⁄ my1 c l r e d t n a m e ur cqcqcq ur c l r e d t n a m e g r p my call sign ： ja3yua cq s #allinganindividualstation ur my my ja3yua ⁄ my1 c l r e d t n a m e ur jg3ymk ur c l r e d t n a m e ...

  • Page 116: 2Epeateroperationusingthe6&/

    107 8 dv mode operation s #alling#1 my call sign ： ja3yua cq area zone repeater q ： jp3yhl q w e r r2 r2 r2 c l r e d t n a m e g r p r1 r1 jp3yhl r1 c l r e d t n a m e g r p ur my my ja3yua ⁄ my1 c l r e d t n a m e ur cqcqcq ur c l r e d t n a m e g r p s #allinganindividualstation my call sign ：...

  • Page 117

    108 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 s #alling#1 my call sign ： ja3yua repeater q ： jp3yhl repeater r ： jp3yhj cq q w e r area zone s #allinganindividualstation my call sign ： ja3yua station call sign ： jg3ymk repeater q ： jp3yhl repeater r ： jp3yhj q w e r a...

  • Page 118

    109 8 dv mode operation q select the desired frequency band. (p. 35) w push [vfo/memo] to select the vfo mode. E push [dv s dr] to select the dv mode. R set the repeater’s transmit frequency, duplex direc- tion and offset. (pp. 37, 65, 163) t push [menu] one or more times to display the “m3” screen ...

  • Page 119

    110 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d 3ettingsfor “ ur ” and “ 2 ” dependingonthecommunicationform $estination#1 $estination!Nindividualstation #ommunicationform,ocalareacall cq s52setting#1#1#1 s2setting./453% 1 #ommunicationform,ocalareacall s52setting!Nin...

  • Page 120: -Essageoperation

    111 8 dv mode operation n -essageoperation d 48messageprogramming the transceiver has a total of 5 message memories to store short messages to transmit during dv mode operation. Message of up to 20 characters can be pro- grammed for each memory. Q in the dv mode, push [menu] one or more times to dis...

  • Page 121

    112 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d -essage4ransmission 9oucanselectamessagechannel4-n4- toturn on the message transmission function. When a mes- sage channel is selected, the transceiver transmits the pre-programmed text message. The default setting is of...

  • Page 122: $6Automaticdetection

    113 8 dv mode operation n $6automaticdetection when a non-digital signal is received during dv mode operation, the “dv” and “fm” icons simultaneously blink. The transceiver automatically selects the fm mode to monitor the signal, if the dv auto detect func- tion is turned on. Q in the dv mode, push ...

  • Page 123: $Igitalsquelchfunctions

    114 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n $igitalsquelchfunctions the digital squelch opens only when receiving a sig- nal addressed to your own call sign, or a signal that includesamatchingdigitalcode9oucansilentlywait for calls from others. ./4% use digital co...

  • Page 124: %-2Communication

    115 8 dv mode operation n %-2communication the emr (enhanced monitor receive) communication mode can be used in only the dv mode. In the emr mode, no call sign setting is necessary. When an emr mode signal is received, the audio (voice) will be heard at the specified level, even if the volume settin...

  • Page 125: "+Modecommunication

    116 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n "+modecommunication the bk (break-in) function allows you to break into a conversation, where the two other stations are com- municating with call sign squelch enabled. Q while receiving another station’s communication i...

  • Page 126: 0Acketlossindication

    117 8 dv mode operation in addition to digital voice communication, low-speed data communication can be made. Use the optional opc-1529r data communication cable with a third-party serial data communication software. S!53"portcanalsobeusedforthelowspeeddatacom - munication, depending on the “usb2/da...

  • Page 127: $63Etmodedescription

    118 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n $63etmodedescription the dv set mode is used for programming infrequently changed values or functions in the dv mode. D dv 3etmodesettings q in the dv mode, push [menu] one or more times to display the “m3” screen (menu ...

  • Page 128

    119 8 dv mode operation 282047rite 7. $efault/&& turn the repeater call sign automatic write function on or off. When you receive a call addressed to your own call sign through a repeater, this function automatically sets the repeater call signs included in the signal, into your current “r1” and “r2...

  • Page 129

    120 8 dv mode operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 /pening#all3ign 17. $efault/&& 3electwhetherornottodisplay-9callsignonthe lcd when the transceiver is turned on. S off : turns off the function. S/. $isplays-9callsignatpower/. "+ 18. $efault/&& the break-in function allow...

  • Page 130: Gps/gps-A Operation

    9 121 gps/gps-a operation n '03operation 9oucandisplayyourown'03datainalloperating modes9oucanalsotransmit'03datawheninthe dv mode. To receive gps data, connect a third-party gps receiver that has an rs-232c output and nmea data format. Third-party gps receivers connect to the [data1] jack of the tr...

  • Page 131

    122 9 gps/gps-a operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d 3entenceformattersetting q hold down [call/gps] for 1 second to display the “gps” screen. W push [set](f-5) to enter the gps set mode. E push [ y ](f-1) or [ z ](f-2) to select “gps tx mode.” r rotate [main dial] to se...

  • Page 132

    123 9 gps/gps-a operation n gps operation (continued) d 0ositiondisplay q hold down [call/gps] for 1 second to display the “gps” screen. W push [pos](f-1) to display the position data. Then push [f-2] one or more times to display your current position, received position or gps memory alarm position ...

  • Page 133

    124 9 gps/gps-a operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d '03automatictransmission in the dv mode, this function automatically transmits the gps receiver’s current position data, at a selected interval. When a gps message is programmed, the transceiver transmits it along with...

  • Page 134

    125 9 gps/gps-a operation n gps operation (continued) d '03messageprogramming enter a gps message of up to 20 characters to be transmitted with the position data. Q hold down [call/gps] for 1 second to display the “gps” screen. W push [msg](f-3) to display the “msg” screen (gps message). E push [txm...

  • Page 135

    126 9 gps/gps-a operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d 2eceived'03messagedisplay q hold down [call/gps] for 1 second to display the “gps” screen. W push [msg](f-3) to display the “msg” screen (gps message). E push [rxm](f-2) to display the “rxm” screen (rx message). S-essa...

  • Page 136: '03Memoryoperation

    127 9 gps/gps-a operation n '03memoryoperation the transceiver has 50 gps memory channels to store the received position data, or other-used position data, along with an alphanumeric channel name. D !Dda'03memory q hold down [call/gps] for 1 second to display the “gps” screen. W push [gpm](f-2) to d...

  • Page 137

    128 9 gps/gps-a operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 ,atitudedataprogramming u when “lat” is selected, rotate [main dial] to enter the desired latitude data. S!Cursorblinksontheprogrammabledigit s0ush; Ω ≈ ](f-3) to select the digit. S3electh.Vtoinput..Orthlatitude s3elect...

  • Page 138

    129 9 gps/gps-a operation n gps memory operation (continued) d %dita'03memory the gps memory name, latitude and longitude data, time data and a memory bank name can be edited. Q hold down [call/gps] for 1 second to display the “gps” screen. W push [gpm](f-2) to display the “gpm” screen (gps memory)....

  • Page 139

    130 9 gps/gps-a operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d '03alarmsetting a gps alarm can sound when a target position comes into the alarm area. This function can be set to the caller station, all gps memory channels, a specified memory bank or a specified memory channel. Q ...

  • Page 140

    131 9 gps/gps-a operation n gps memory operation (continued) d '03memoryclearing s#learallmemorychannels q hold down [call/gps] for 1 second to display the “gps” screen. W push [gpm](f-2) to display the “gpm” screen (gps memory). E rotate [main dial] to select “all.” r hold down [clr](f-3) for 1 sec...

  • Page 141: Gps Set Mode

    132 9 gps/gps-a operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n gps set mode the following individual settings are selectable in the gps set mode. Set them to suit your gps operating needs. Q hold down [call/gps] for 1 second to display the “gps” screen. W push [set](f-5) to enter ...

  • Page 142

    133 9 gps/gps-a operation n gps set mode (continued) !Larm!Rea 9. $efaultg when the gps alarm function is set to “all” or one of the memory banks, set the gps alarm active range. When ddd°mm.Mm’ is selected in “position format,” the active range can be set to between 0’08" and 59’99" in 0’01" steps....

  • Page 143

    134 9 gps/gps-a operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 gps auto tx 11. $efault/&& select the desired interval from off, 5, 10, 30 sec- onds, 1, 3, 5, 10 or 30 minutes for automatic position data transmission. The current position data, received from a gps re- ceiver, is tran...

  • Page 144

    135 9 gps/gps-a operation n gps set mode (continued) $ata%xtension 20. * $efault/&& set the data extension capability to “course/speed” or off. When you select “course/speed,” the transceiver’s course and speed information is transmitted along with the position data. ./4% when “course/speed” is sele...

  • Page 145

    136 9 gps/gps-a operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 #omment 24. * program a comment of up to 43 characters. The programmed comment is transmitted with the gps position data. See ‘comment programming,’ as described below. This item appears when “data extension” is set to o...

  • Page 146: '03!operation

    137 9 gps/gps-a operation n '03!Operation d '03!Function set the following to activate the gps-a function. Q push [dv s dr] to select the dv mode. W enter the gps set mode. E set the desired position data transmitting interval in “gps auto tx.” (p. 134) r select “gps-a” in “gps tx mode.” (p. 134) t ...

  • Page 147: Memory Operation

    10 138 memory operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 'eneraldescription the transceiver has 106 memory channels in each fre- quency band. (99 regular, 6 scan edges and 1 call) the memory mode is very useful to quickly change to often-used frequencies. While in the memory m...

  • Page 148: -Emorychannelselection

    139 10 -%-/29/0%2!4)/. N -emorychannelselection when the sub band setting is turned on, you can se- lect a memory channel in the sub band as well as in the main band. (p. 33) sh ” appears when the sub band setting is on. D 3electioninthe6&/mode q push [vfo/memo] to select the vfo mode. W rotate [m-c...

  • Page 149: -Emorychannelprogramming

    140 10 -%-/29/0%2!4)/. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 memory channels can be programmed in either the vfo mode or the memory mode. D 0rogramminginthe6&/mode q push [vfo/memo] to select the vfo mode. W set the desired settings into both vfo a and vfo b. ± select the band using ...

  • Page 150: #allchannelprogramming

    141 10 -%-/29/0%2!4)/. N #allchannelprogramming the call channel is programmed in the same way as the regular memory channels are. It is convenient to program a most-often-used frequency into the call channel for quick recall. As with memory channels, the call channel can also hold split frequencies...

  • Page 151: -Emorycontentscopying

    142 10 -%-/29/0%2!4)/. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 the memory channel contents (frequency, operating mode, etc.) can be copied to the vfo. The copy can be performed in either the vfo mode or the memory mode. D #opyinginthe6&/mode this is useful for copying programmed conten...

  • Page 152: -Emorynameprogramming

    143 10 -%-/29/0%2!4)/. N -emorynameprogramming all memory channels, including scan edges and call channel, can be tagged with alphanumeric names of up to 9 characters each. ;%8!-0,%= programming a memory name into memory channel 99. Q push [vfo/memo] to select the memory mode. W rotate [m-ch] to sel...

  • Page 153: -Emopadfunction

    144 10 -%-/29/0%2!4)/. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 9oucancallupamemopadbypushing;-02=oneor more times while in either the vfo or memory mode. S4hememopaddataiscalledupstartingfromthemost recently written. When you call up a memo pad, the previously dis- played data is autom...

  • Page 154: Scans

    11 145 scans scan – ∂ f frequency + ∂ f frequency center frequency (start frequency) jump mch 1 mch 5 mch 2 mch 3 mch 4 mch 6 mch 7 mch 99 sel sel sel sel sel mch 1 mch 5 mch 2 mch 3 mch 4 mch 6 mch 7 mch 99 sel sel sel sel sel fm fm usb fm cw usb fm fm scan 1a 2a 3a 1b 2b 3b jump scan edges n 3cant...

  • Page 155: 0Reparation

    146 11 scans 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 0reparation &ora0rogrammedscan program scan edge frequencies into program scan edge channels “1a–3a” and “1b–3b.” (p. 148) &ora-emoryscan program two or more memory channels. (program scan edge channels will not be scanned.) (p. 14...

  • Page 156: 3Cansetmode

    147 11 scans n 3cansetmode the scan speed, scan resume function and [main dial] scan function can be set in the scan set mode. Q push [menu] one or more times to display the “m2” screen (menu 2). W push [scan](f-1) to display the “scan” screen. E push [set](f-5) to enter the scan set mode. R push [ ...

  • Page 157: 3Canedgesprogramming

    148 11 scans 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 3canedgesprogramming memory channels 1a–3a and 1b–3b are the program scan edge channels. They are used to program the upper and lower frequency edges for programmed scans. (p. 149) each frequency band has its own scan edge chan- ne...

  • Page 158

    149 11 scans a programmed scan searches for signals between program scan edge channels “1a–3a” and “1b–3b.” before starting the programmed scan, scan edges must be programmed into these channels. See the previous page for scan edge programming. If the same frequencies are programmed into the program...

  • Page 159: -Emoryscan-Emorymode

    150 11 scans 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d -emoryscan a memory scan searches for signals through memory channels 1 to 99. Blank (unprogrammed) memory channels are skipped. ./4% for a memory scan to start, two or more memory channels must be programmed. (p. 140) q push [vfo/...

  • Page 160

    151 11 scans !Boutthescantypeswitchingprocedure 9oucanswitchthescantypebetweenvariousscanswhilescanningasshownbelow m e m ∂ f span s e t s e l scan sel − memo scan select memory scan m e m ∂ f span s e t s e l scan sel − memo scan select memory scan d 3elect-emoryscan select memory scan searches for...

  • Page 161: &scanand&ine

    152 11 scans 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 ∂ f (delta frequency) scan searches for signals within the specified range with the displayed vfo frequency or memory channel frequency as the center frequency. The frequency range is specified by the width of the selected span. Q pu...

  • Page 162: Satellite Operation

    12 153 satellite operation both satellite mode b (435 mhz uplink, 145 mhz downlink) and mode j (145 mhz uplink, 435 mhz downlink) can be operated with the ic-9100, and mode l can be operated when the optional ux-9100 1200 mh z band unit is installed. Satellite communications is possible only when a ...

  • Page 163: 3Ettingthesatellite6&/

    154 12 satellite operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 3ettingthesatellite6&/ q push [satellite] to enter the satellite mode. S “ ” and either “ ” or “ ” appear. W push [vfo/memo] to toggle between the satellite vfo and memory mode. S6&/or-emorymodedataisdisplayedonthe35"...

  • Page 164: 3Atellitememory

    155 12 satellite operation n 3atellitememory the ic-9100 has 20 satellite memory channels (ch 00 to 19) to memorize both uplink and downlink frequen- cies, operating modes and other data. D 3atellitememoryselection q push [satellite] to enter the satellite mode. W push [vfo/memo] to select the satel...

  • Page 165: 0Reparation

    156 12 satellite operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 0reparation q decide on a usable satellite, and point your antenna direction towards it. W confirm the approximate location of the satellite and operating mode (e.G. “b,” “j,” etc.) through a publication (magazine, et...

  • Page 166: 3Atelliteoperation

    157 12 satellite operation n 3atelliteoperation when your own signal can be received with a loop test, satellite communication can be performed. Q when a frequency is shifted by the doppler effect, push [sub](3.5 2), then rotate [main dial] to re- tune the uplink frequency. S4hedownlinkfrequencydisp...

  • Page 167: Antenna Tuner Operation

    13 158 antenna tuner operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 the ic-9100 has 2 antenna connectors for the hf/50 mhz bands, [ant1] and [ant2], and a dedicated an- tenna connector for each of the 144 mhz, 430 mhz and-(zbandsatotalofantennaconnec - tors. 9ou can memorize the ant...

  • Page 168: !ntennatuneroperation

    159 13 antenna tuner operation m )fthetunercannottunetheantennacheckthe followingandtryagain sthecorrectantennaconnectorselection stheantennaconnectionandfeedline stheuntunedantenna372,essthanforthe (&bands,essthanforthe-(zband sthetransmitpower7forthe(&bands7for the 50 mhz band) sthepowersourcevolt...

  • Page 169

    160 13 antenna tuner operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 s !((&-(z!54/-!4)#!.4%..!45.%2 the optional ah-4 matches the ic-9100 to a long wire antenna more than 7 m/23 ft long (3.5 mhz and above). S3eepageforthetransceiverand!(connec - tion. S3eethe!(instructionmanualinstal...

  • Page 170: Set Mode

    14 161 set mode n 3etmodedescription the set mode is used for programming infrequently changed values or functions. D 4he3etmodesettings q hold down [menu] for 1 second to enter the set mode. W push [ y ](f-1) or [ z ](f-2) to select the desired item. E rotate [main dial] to select the desired optio...

  • Page 171

    162 14 set mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 5ser"and%dge 7. This “user band edge” item appears only when “on 5ser vorh5ser/. 48visselectedintheh"and edge beep” item. (p. 161) 7henyouselecth/.5ser vorh/.5ser 48vin the “band edge beep” item, you can program a total of 30 band...

  • Page 172

    163 14 set mode $50/ffset 18. 3ettheoffsetforduplexoperation9oucansetthe repeater offset for each band. *the difference between transmit and receive frequencies. ± when you select this item, hold down [band](main/ sub) for 1 second to select the desired frequency band. Then, rotate [main dial] to se...

  • Page 173

    164 14 set mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 30%%#(,evel 25. $efault !Djustthespeechaudiooutputleveltobetween nooutput andmaximumoutput 30%%#(,anguage 26. $efault%nglish select english or japanese as the speech language. 30%%#(3peed 27. $efault()'( select high (faster) or lo...

  • Page 174

    165 14 set mode ;./4#(=3733" 36. $efault!Uto-anual select the auto, manual or auto/manual notch filter to be used for ssb mode operation. S!Uto only the auto notch filter can be used. S-anual /nly the -anual notch filter can be used. S!Uto-anual"oththe!Utoand-anualnotchllters can be used. ;./4#(=37!...

  • Page 175

    166 14 set mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 %840!-0 47. $efault/&& switch the preamplifier control on or off. When using the optional ag-1200*, on must be selected. Otherwise, the preamplifier will not function. *ag-1200 has been discontinued, but it can be still be used. #...

  • Page 176

    167 14 set mode %xternal+eypad 54. $efault/&& turn the external keypad on or off for keyer mem- ory transmission. See page 26 for the equivalent circuit of an external keypad and connection. S/&& 4heexternalkeypaddoesnotfunc - tion. S+%9%23%.$)nthe#7modepushingoneofex - ternal keypad switches transm...

  • Page 177

    168 14 set mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 53"$!4!&unc 64. $efault;'03= select the function of the [data1] jack. S ----- : the [data1] jack is not used. S2449 5sedtosend2449decodedsignals s$6dat 5sedforlowspeeddatainputandoutput s'03 5sedforthe'03receiverconnectionfor posi...

  • Page 178

    169 14 set mode d the 4onecontrol3etmodesettings q push [menu] one or more times to display the “m2” screen (menu 2). W push [tcon](f-4) to enter the tone control set mode. E push a mode switch to select the desired operating mode. R push [ y ](f-1) or [ z ](f-2) to select the desired item. S3electa...

  • Page 179

    170 14 set mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 4"7-)$ , 9. $efault -ode33" set the lower cut-off frequency of the transmission passband width for your mid setting to 100, 200, 300 or 500 hz. 4"7-)$ ( 10. $efault -ode33" set the higher cut-off frequency of the transmission pass...

  • Page 180: Data Communication

    15 171 data communication n #onnections tnc data in data out(9600bps) gnd af out(1200bps) pttp rear panel view tx audio rx audio ptt gnd sql* q r w t e y sql data in data out(9600bps) gnd af out(1200bps) pttp tx audio rx audio ptt gnd sql* q r w t e y sql pc rs-232c tnc tnc tnc pc rs-232c rear panel...

  • Page 181: 0Acket!&3+ Operation

    172 15 data communication 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 0acket!&3+ operation before operating packet (afsk), be sure to consult the operating manual that came with your tnc. Q connect the tnc and pc. (p. 171) w select the desired band. (p. 35) e push [ssb] or [am/fm] to sel...

  • Page 182: !djustingthe4.#outputlevel

    173 15 data communication when the data transmission speed is set to 9600 bps, the data signal coming from the tnc is applied exclu- sively to the internal limiter circuitry to automatically maintain band width. Never apply data levels from the tnc of over 0.6 vp-p. Otherwise the transceiver will no...

  • Page 183: Option Installation

    16 174 option installation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n /peningthetransceiverscase the following are instructions for removing the covers of the ic-9100. R warning! Turn off the power and disconnect the dc power cable from the transceiver before per- forming any work on th...

  • Page 184: Ux-9100

    175 16 option installation n ux-9100 1200 mhz band unit installation the optional ux-9100 is required to operate on the 1200 mhz frequency band. Q remove the top and bottom covers as shown in the diagram on page 174. W remove the antenna plate from the chassis on the rear panel using a standard flat...

  • Page 185: Ut-121

    176 16 option installation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n ut-121 digital unit installation n fl-430/fl-431 1 st if filter installation the optional filters, fl-430 1 st if filter (6 k h z ) or fl- 431 1 st if filter (3 k h z ) provides 6 or 3 khz filtering to reduce interfer...

  • Page 186: Maintenance

    17 177 maintenance d 4ransceiverpower 02/",%- 0/33)",%#!53% solution ref. Power does not turn on when the [power] switch is pushed. S4hepowercableisimproperlyconnected s!Fuseisblown s2econnectthe$#powercablecorrectly s#orrectthecausethenreplacethefusewith an equivalent fuse. ( fuses are installed in...

  • Page 187

    178 17 maintenance 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d 3canning 02/",%- 0/33)",%#!53% solution ref. Programmed scan does not stop. S3quelchisopen s3et the ;2&31,= control to the threshold point. Pp. 44, 146 programmed scan does not start. S the same frequencies have been programm...

  • Page 188: &requencycalibration

    179 17 maintenance n &requencycalibration approximate [pbt-clr] [ ] (main band) [ ] (main band) [ ] [ ] [ ] [ ] [ ] [ ] [main dial] Ù 68 Ú o f f set c a l i b r a t i o n m a r k e r Ù 69 Ú 5 0 % set r e f a d j u s t s#alibrationmarkeritem s2%&!Djustitem a very accurate frequency counter is require...

  • Page 189: &usereplacement

    180 17 maintenance 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d #ircuitryfusereplacement except for the power amplifier, the 13.8 v dc from the dc power cable is applied to all units in the ic-9100, through the circuitry fuse. This fuse is located in the pa unit. Q remove the top cover. (...

  • Page 190: 2Esettingthe#05

    181 17 maintenance n 2esettingthe#05 d 0artialreset if you want to reset the operating parameters to their default values (vfo frequency, vfo settings, menu group’s contents) without clearing certain data as de- scribed below, a partial reset can be performed. The following data will not be cleared ...

  • Page 191: $Atacloning

    182 17 maintenance 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n $atacloning d #loningbetweentransceivers the ic-9100 has transceiver-to-transceiver data clon- ing capability. This function is useful when you want to copy all of the programmed contents from one ic-9100 to another. S!Minipl...

  • Page 192: Control Command

    18 183 control command n 2emotejack#)6 information controller to ic-9100 fe fe 7c e0 cn sc data area fd preamb le code (fix ed) tr ansceiv er’ s def ault address controller’ s def ault address command number (see the command tab le) sub command number (see the command tab le) bcd code data such as f...

  • Page 193

    184 18 control command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 d #ommandtable cmd. Sub cmd. $ata $escription 00 see p. 190 send operating frequency for transceive 01 see p. 190 send operating mode for transceive 02 see p. 191 read band edge frequencies 03 see p. 190 read operating freq...

  • Page 194

    185 18 control command d command table (continued) cmd. Sub cmd. $ata $escription 15 01 00 read squelch status (squelch close) 01 read squelch status (squelch open) 02 0000 to 0255 read s-meter level 333d" 11 0000 to 0255 read rf power meter 12 0000 to 0255 read swr meter 372372 372372 13 0000 to 02...

  • Page 195

    186 18 control command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 cmd. Sub cmd. $ata $escription 1a 05 0016 00 send/read split lock function off 01 send/read split lock function on 0017 see p. 192 send/read duplex offset frequency 0018 00 send/read one touch repeater dup– 01 send/read one...

  • Page 196

    187 18 control command d command table (continued) cmd. Sub cmd. $ata $escription 1a 05 0054 0000 to 0255 send/read usb modulation level to 0055 00 send/read 9600 bps mode off 01 send/read 9600 bps mode on 0056 00 send/read mic selection for the modula- tion input during data mode off 01 send/read a...

  • Page 197

    188 18 control command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 cmd. Sub cmd. $ata $escription 1a 05 0101 00 send/read normal selection for paddle polarity 01 send/read reverse selection for paddle polarity 0102 00 send/read straight selection for keyer type 01 send/read bug-key selecti...

  • Page 198

    189 18 control command cmd. Sub cmd. $ata $escription 1a 05 0146 00 send/read dr call sign popup off 01 send/read dr call sign popup on 0147 00 send/read opening call sign off 01 send/read opening call sign on 0148 00 send/read bk function off 01 send/read bk function on 0149 00 send/read emr mode o...

  • Page 199

    190 18 control command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 cmd. Sub cmd. $ata $escription 20 02 00 00* 2 send/read auto dv rx status output off 01* 2 send/read auto dv rx status output on 01 see p. 194 output dv rx status 02 see p. 194 read dv rx status * 1 the counter can be inser...

  • Page 200

    191 18 control command s"andedgefrequencysetting command 02*, 1e 01, 1e 03 q x x x w e r t y u i o !0 !1 !2 x x x x x x x x x 2 d x x x x x x x x x x 10 hz digit: 0–9 1 hz digit: 0–9 1 khz digit: 0–9 100 hz digit: 0–9 100 khz digit: 0–9 10 khz digit: 0–9 10 mhz digit: 0–9 1 mhz digit: 0–9 1000 mhz d...

  • Page 201

    192 18 control command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 s3plitoffsetfrequencysetting command : 1a 05 0015 1 khz digit: 0–9 100 hz digit: 0 (fix ed) 100 khz digit: 0–9 10 khz digit: 0–9 10 mhz digit: 0 (fix ed) 1 mhz digit: 0–9 direction: 00: + direction 01: – direction q 0 x x x...

  • Page 202

    193 18 control command s!Larmareasetting command : 1a 05 0159 q x x x x 0 w e 0 10 min. Digit: 0–5 1 min. Digit: 0–9 0.1 min. Digit: 0–9 0.01 min. Digit: 0–9 0.001 min. Digit: 0–9 0 (fix ed) s5nproto!Ddresssetting command : 1a 05 0169 set an unproto address of up to 56 characters. See ‘character cod...

  • Page 203

    194 18 control command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 s$648callsignssetting command : 1f 01 set “ur,” “r1” and “r2” call signs of 8 characters (fixed). X x …… x x x x x x x x x x …… !7 – @4 o – !6 q – i …… q – i ur (destination) call sign setting o – !6 r1 (access/area repeate...

  • Page 204

    195 18 control command d data content description (continued) q frequency band setting 00 : hf/50 mhz frequency band 01 : 144 mhz frequency band 02 : 430 mhz frequency band 03 : 1200 mhz frequency band w , e memory channel number 0001–0099 : memory channel 1 to 99 0100 : programmed scan edge 1a 0101...

  • Page 205

    196 18 control command 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 q , w satellite memory channel number 0000–0019 : satellite memory channel 00 to 19 e – u operating frequency setting 3ee@s/peratingfrequencyp i , o operating mode setting 3ee@s/peratingmodep !0 data mode setting 1 byte dat...

  • Page 206: Specifications

    19 197 specifications n 'eneral s&requencycoverage unit-(z receive 0.030–60.000* 1 * 2 136.000–174.000* 1 * 2 420.000–480.000* 1 * 2 1240.000–1320.000 † transmit 1.800–1.999* 2 , 3.500–3.999* 2 , 5.33050* 3 , 5.34650* 3 , 5.36650* 3 , 5.37150* 3 , 5.40350* 3 , 7.000–7.300* 2 , 10.100–10.150* 2 , 14....

  • Page 207: 2Eceiver

    198 19 specifications 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 n 2eceiver s2eceivesystem hf/50/144/430 mhz band : double superheterodyne system 1200 mhz band † : triple superheterodyne system s)ntermediatefrequencies 1st : 64.455 mhz (hf/50 mhz band) 10.850 mhz (144 mhz band) 71.250 mhz...

  • Page 208: Options

    20 199 options ah-4 hf automatic antenna tuner specially designed to tune a long wire antenna for the hf/50 mhz bands, particularly in portable or mobile oper- ation. The “ptt tune” function pro- vides simple operation. S)nputpowerrating7 ah-2b antenna element a 2.5 m long antenna ele- ment for mobi...

  • Page 209

    200 20 options 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 ct-17 ci - v level converter unit for remote transceiver control using a personal computer equipped with an 23# port 9ou can change fre - quencies, operating mode, memory channels, etc., via your computer. S ag-25 weather - proof p...

  • Page 210

    21 201 ce installation notes for amateur base station installations it is recom- mended that the forward clearance in front of the an- tenna array is calculated relative to the eirp (effective isotropic radiated power). The clearance height below the antenna array can be determined in most cases fro...

  • Page 211

    202 21 ce 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 declaration of conformity we icom inc. Japan 1-1-32, kamiminami, hirano-ku osaka 547-0003, japan kind of equipment: type-designation: signature authorized representative name place and date of issue version (where applicable): y . F uru...

  • Page 212

    1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan a-6871h-1ex printed in japan © 2011 icom inc. At fi it pl gb ro be fr lv pt is tr cy de lt sk li hr cz gr lu si no dk hu mt es ch ee ie nl se bg at fi it pl gb ro be fr lv pt is tr cy de lt sk li hr cz gr lu si no dk hu mt es ch ee ie nl se bg at f...