- DL manuals
- Icom
- Transceiver
- IC-F111S
- Instruction Manual
Icom IC-F111S Instruction Manual
Summary of IC-F111S
Page 1
If111s vhf transceiver instruction manual uhf transceiver if121s if211s if221s ic-f111s_f121s_f211s_f221s 02.10.3 11:54 am page a (1,1).
Page 2
I important explicit definitions rwarning! Never connect the transceiver to an ac outlet. This may pose a fire hazard or result in an electric shock. Caution! Never touch the transceiver (especially the heat sink) when transmitting continuously for long peri- ods. It will become hot. Never connect t...
Page 3
Ii use the supplied microphone only. Other microphones have different pin assignments and may damage the trans- ceiver. Do not use or place the transceiver in areas with tempera- tures below –22°f (–30°c) or above +140°f (+60°c), or in areas subject to direct sunlight, such as the dashboard of a veh...
Page 4: Panel Description
1 1 panel description tx/rx 1 2 3 4 q w e r function led (p. 2) ■front panel qaf volume control knob ➥rotate the knob to adjust the audio output level. • minimum audio level is pre-programmed. Wmicrophone connector ➥connect the supplied microphone or optional dtmf micro- phone. Never connect non-spe...
Page 5: ■Function Led
2 1 panel description ■function led qchannel indicators ➥ indicates the operating channel. ➥ blinks when receiving a signal during scanning opera- tion. ➥ all leds blink while entering the power on password. Wtx/rx indicator ➥ lights red: while transmitting ➥ lights green: while the channel is busy ...
Page 6
3 1 panel description ■programmable function keys the following functions can be assigned to [p0], [p1], [p2] and [p3] programmable function keys. Consult your icom dealer or system operator for details con- cerning your transceiver’s programming. In the following explanations, programmable function...
Page 7
4 1 panel description ¡ ¡ talk around key turns the talk around function on and off. • the talk around function equalizes the transmit frequency to the receive frequency for mobile-to- mobile communication. ¡ ¡ wide/narrow key push this key to toggle the bandwidth between wide or narrow. ¡ ¡ dtmf au...
Page 8
5 1 panel description ¡ ¡ emergency key push and hold the key to transmit an emergency call. • if you want to cancel the emergency call, push and hold (or push) the key again before trans- mitting the call. • depending on the pre-setting, the emergency call is transmitted one time only, or repeatedl...
Page 9: Operation
6 2 operation ■turning power on q push [ ] to turn the power on. W if the transceiver is programmed for a start up passcode, input the digit codes as directed by your dealer. • the keys in the table below can be used for password input: • the transceiver detects numbers in the same block as identica...
Page 10
7 2 operation ■receiving and transmitting receiving: q push [power] to turn the power on. W push [ch up] or [ch dn] to select a channel. E when receiving a call, adjust the audio output level to a comfortable listening level. Transmitting: r take the microphone off hook. • the channel is busy when t...
Page 11
8 2 operation d scrambler function the ut-109 (#02) or ut-110 (#02) optional voice scrambler unit provides high performance private communication between stations with the same scrambler codes. Q push and hold [scrm] to turn the scrambler function on. W push [scrm] to turn the function off. D user s...
Page 12: Connection And Maintenance
9 3 connection and maintenance optional cable (opc-617) q antenna never connect to a 24 v battery. + red: black: 12v battery solder crimp note: use the terminals as shown below for the cable connections. R c a u t i o n ! N e v e r r e- move the fuse-holder from the dc power cable. E r t w to the an...
Page 13: ■Supplied Accessories
10 3 connection and maintenance q antenna connector connects to an antenna. Ask your dealer about antenna selection and placement. W microphone hanger connect the supplied microphone hanger to the vehicle’s ground for microphone on/off hook functions. (see p. 1) e dc power receptacle connects to a 1...
Page 14: ■Mounting The Transceiver
11 3 connection and maintenance ■mounting the transceiver the universal mounting bracket supplied with your transceiv- er allows overhead mounting. • mount the transceiver securely with the 4 supplied screws to a thick surface which can support more than 1.5 kg. Flat washer spring washer when using ...
Page 15: ■Optional Ut-109 /ut-110
12 3 connection and maintenance ■optional ut-109 /ut-110 installation q turn the power off, then disconnect the dc power cable. W unscrew the 4 screws, then remove the bottom cover. E cut the pattern on the pcb at the tx mic circuit (mic) and rx af circuit (disc) as shown below. R install the scramb...
Page 16: ■ Antenna
13 3 connection and maintenance ■ antenna a key element in the performance of any communication sys- tem is an antenna. Ask your dealer about antennas and the best places to mount them. ■ fuse replacement a fuse is installed in the supplied dc power cable. If a fuse blows or the transceiver stops fu...
Page 17: Options
14 4 options sp-22 external speaker compact and easy-to-install. Input impedance : 4 Ω max. Input power : 5 w hm-100tn dtmf microphone. Sm-25 desktop microphone. Ut-108 dtmf decoder unit provides pager and code squelch capabilities. Ut-109/ut-110 (#02) voice scrambler unit • ut-109 : non-rolling typ...
Page 18: Safety Training Information
Your icom radio generates rf electromag- netic energy during transmit mode. This radio is designed for and classified as “occupational use only”, meaning it must be used only during the course of employ- ment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is n...
Page 19
Memo ic-f111s_f121s_f211s_f221s 02.10.3 11:54 am page 16 (1,1).
Page 20
Count on us! 1-1-32 kamiminami, hirano-ku, osaka 547-0003 japan a-6199h-1ex printed in japan © 2002 icom inc. Ic-f111s_f121s_f211s_f221s 02.10.3 11:54 am page z (1,1).