1. DL manuals
  2. Icom
  3. Two-Way Radio
  4. IC-F5060 Series
  5. Operating Manual

Icom IC-F5060 Series Operating Manual

Other manuals for IC-F5060 Series: Manual, Instruction Manual, Operating Manual, Instruction Manual

Summary of IC-F5060 Series

  • Page 1

    Operating guide operating guide for ic-f5060/f6060 series biis 1200/mdc 1200 system/ ltr ® /idas™ operation.

  • Page 2

    Thank you for purchasng ths icom transcever. The biis 1200/mdc 1200 system/ltr ® /idas™ (icom dgtal advanced system) functons are avalable to your ic-f5060/ f6060 seres transcever. Read all instructions carefully and completely before usng the transcever. Save this operating guide — ths operatng gud...

  • Page 3

    Table of contents important .......................................................................... Table of contents ........................................................ 1 preparation............................................................1−2 ■ programmable functon keys ....................

  • Page 4: Preparation

    1 1 preparation ■ programmable function keys the followng functons can be assgned to [up], [down], [p0], [p1], [p2], [p3] and [p4] programmable functon keys. Consult your icom dealer or system operator for detals con- cernng your transcevers programmng. If the programmable functon names are brackete...

  • Page 5

    D for ltr operation only phone key push to connect or dsconnect the telephone network con- necton. D for idas operation only digital button key ➥ push to enter the applcaton selecton mode. ➥ push and hold for 1 sec. To toggle the call type between indvdual and talkgroup, then enter the applcaton sel...

  • Page 6: Biis 1200 Operation

    3 2 biis 1200 operation ■ setting example the followng key functons are recommended to be as- sgned to each programmable key for the biis 1200 opera- ton. The key functon can be assgned by your dealer. Ask your dealer for detals. Note: durng biis 1200 operaton, mdc 1200 system, ltr and idas operaton...

  • Page 7

    4 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d group call q when a group call s receved; • beeps sound. • “ ” appears and the mute s released. • “ ” appears or blnks dependng on the settng. • the group id (or text) and the callng staton id (or text) s ds- played when the ndcaton mo...

  • Page 8: Transmitting A Call

    5 2 biis 1200 operation ■ transmitting a call a total of 3 ways for code selecton are avalable— selectng the call code from memory, enterng the call code from the keypad and callng back from the queue channel record. D using call memory q durng stand-by operaton, push [biis button] to enter the call...

  • Page 9

    6 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d direct code entry q durng stand-by operaton, push [tx code enter] to enter the tx code edt mode. • code dgt for edtng blnks. 1 2 3 4 w push [tx code enter] to select the desred dgt to be edted. • dgt for edtng dffers accordng to the se...

  • Page 10: Receiving A Message

    7 2 biis 1200 operation ■ receiving a message d receiving a status message q when a status message s receved; • beeps sound. • the status message and the callng staton id (or text) s ds- played when the ndcaton mode s 2 lnes as below. • the status message and the callng staton id (or text) s ds- pla...

  • Page 11

    8 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d received message selection the transcever memorzes the receved message n the memory. Up to 6 messages for status and sdm, or 95 char- acter sdm’s can be memorzed. The oldest message s erased when the 7th message s receved. However, onc...

  • Page 12: Transmitting A Status

    9 2 biis 1200 operation ■ transmitting a status d general the status message can be selected wth the programmed text, and the message text s also dsplayed on the functon dsplay of the called staton. Up to 24 status types (1 to 24) are avalable, and the status messages 22 and 24 have desgnated meanng...

  • Page 13: Transmitting An Sdm

    10 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ transmitting an sdm d general the short data message, sdm, can be sent to an ndvdual staton or group statons. Also, 8 sdm memory channels are avalable and the messages can be edted va pc program- mng. D transmitting an sdm q durng sta...

  • Page 14: Position Data Transmission

    11 2 biis 1200 operation • available characters key [0] [1] [2] [3] [4] [5] [6] [7] [8] [9] characters 0 ! ? ' " , ; : _ ( ) [ ] 1 (space) # * / + - = & % $ @ ^ 2 a b c a b c 3 d e f d e f 4 g h i g h i 5 j k l j k l 6 m n o m n o 7 p q r s p q r s 8 t u v t u v 9 w x y z w x y z / ! ■ position data...

  • Page 15: Printer Connection

    12 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ printer connection when the prnter s connected to the d-sub 25-pn of the transcever, the receved sdm content and the called staton id can be prnted out. Ask your dealer or system operator for connecton detals. ■ biis ani the own id ca...

  • Page 16: Stun Function

    13 2 biis 1200 operation ■ stun function when the specfied id, set as a kller id, s receved, the stun functon s actvated. When the kller id s receved, the transcever swtches to the password requred condton. Enterng of the password va the keypad s necessary to operate the transcever agan n ths case. ...

  • Page 17: Horn Output

    14 2 biis 1200 operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ horn output automatc honkng functon s avalable when the horn honk equpment s connected to d-sub 25-pn of the transcever. When a status message s receved, the transcever controls the vehcle’s horn for the specfed tme perod to nform a s...

  • Page 18: Mdc 1200 System Operation

    15 3 mdc 1200 system operation ■ mdc 1200 system operation the mdc 1200 sgnalng system enhances your transcever’s capabltes. It allows ptt id, selectve callng (selcall), call alert, rado check, stun, revve, status, messagng and emergency sgnalng. An addtonal feature of mdc 1200 system found n icom t...

  • Page 19

    16 3 mdc 1200 system operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d receiving a call alert q when a call alert s receved; • beeps sound. • “ ” blnks. • the callng staton id (or alas) and “ callalrt” are dsplayed alternately. C a l l a l r t i d 1 2 3 4 blinks w push and hold [ptt] and speak nto ...

  • Page 20

    17 3 mdc 1200 system operation d receiving a message q when a message s receved; • beeps sound. • the callng staton id (or alas) and the message are dsplayed alternately. I d 1 2 3 4 m s g 1 w turn power off, push [ptt], change the channel, etc. To stop the dsplay ndcaton. D receiving a status messa...

  • Page 21: Transmitting A Call

    18 3 mdc 1200 system operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ transmitting a call d transmitting a selcall selcall allows you to make a call to a specfc staton or to a partcular group. Other mdc 1200 system transcevers on the channel wll not receve a selcall that does not match ther staton...

  • Page 22

    19 3 mdc 1200 system operation d transmitting a stun call stun call allows you to send mdc 1200 system sgnal that wll stun the targeted staton. Q push [mdc call] to enter the mdc menu selecton mode. W select “ stun” usng [ch up] or [ch down]. S t u n e push [mdc call] agan to enter the transcever al...

  • Page 23

    20 3 mdc 1200 system operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d transmitting a radio check call rado check call allows you to determne whether the tar- geted staton s turned on, wthn the communcaton range and on channel wthout requrng any acton from the tar- geted staton user. Q push [mdc ca...

  • Page 24

    21 3 mdc 1200 system operation d transmitting a message the transcever can send a pre-programmed message. There are 16 messages that can be sent on a channel. Q push [mdc call] to enter the mdc menu selecton mode. W select “ msg” usng [ch up] or [ch down]. M s g e push [mdc call] agan to enter the p...

  • Page 25: Status Message Transmission

    22 3 mdc 1200 system operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ status message transmission the status message can be transmtted automatcally when the transcever s turned on. - set the status message to be transmtted n the ‘power on sta- tus’ tem..

  • Page 26: Ltr Operation

    23 4 ltr operation ■ ltr operation push [zone], then push [ch up] or [ch down]* to select the ltr zone. * the method to select the desred zone may dffer accordng to your system set up. Note: durng ltr operaton, biis 1200 and idas opera- tons are not avalable. ■ receiving a call d group call q when a...

  • Page 27: Transmitting A Call

    ■ transmitting a call d group call q push [ch up] or [ch down] to select a channel or talk group. W whle pushng and holdng [ptt], speak nto the mcro- phone at a normal voce level after a beep s emtted. • if an error beep s emtted, release [ptt]. After a whle, repeat step w. • the beep can be turned ...

  • Page 28: Idas Operation

    ■ idas operation the ic-f5061d and ic-f6061d provdes icom dgtal ad- vanced system (idas) that meets the 6.25 khz emsson mask requrements for narrow bandng, and ncreases effi- cency of channel allocaton and use of spectrum. The optonal ut-126h provdes 6.25 khz dgtal mode opera- ton for the transcever...

  • Page 29

    D receiving a status message q when a status message s receved; • beeps sound. • the callng staton or talkgroup id name (or code) and the sta- tus message blnk. R x s t a t u s 0 1 s t a t i o n 1 blink the received status message the calling station or talkgroup id name w push [ptt], turn power off...

  • Page 30

    27 5 idas operation d receiving a stun, kill or revive if an ndvdual call wth stun or kll command s receved (ran code matchng s not necessary dependng on the pre- settng), the transcever wll dsplay “sorry” and you can not receve * or transmt. * dependng on the receved stun command settng. ➥ when a s...

  • Page 31

    28 5 idas operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d displaying the received call log the transcever stores a log of all calls n memory, f act- vated. Up to 10 call logs can be stored, and the oldest call record s erased when an 11th call s receved. However, once the trans- cever s turned of...

  • Page 32

    29 5 idas operation d talk back function the talk back functon allows you to select the same call mode (analog or dgtal) and/or call type (indvdual or talk- group) for the receved call. When the talk back tmer s set to 0 second, ths functon s not actvated. Ask your dealer for detals. If ths functon ...

  • Page 33: Transmitting A Call

    30 5 idas operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 ■ transmitting a call idas operaton allows you to make a call to a specfic staton (indvdual call) or to a partcular group (talkgroup call). Other dgtal mode transcevers on the channel wll not receve a call that does not match ther ndvdual or...

  • Page 34

    31 5 idas operation d transmitting a call alert call alert allows you to notfy another user who may be away from the transcever that you want to talk. Q push [digital button] to enter the applcaton selecton mode. • “ voice” appears. • to change the call type, push and hold [digital button] for 1 sec...

  • Page 35

    32 5 idas operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d transmitting a stun call a stun call allows you to send a sgnal that wll stun the tar- geted staton. Q push [digital button] to enter the applcaton selecton mode. • “ voice” appears. • to change the call type, push and hold [digital button...

  • Page 36

    33 5 idas operation d transmitting a kill call a kll call allows you to send a sgnal that wll dsable the targeted staton. Q push [digital button] to enter the applcaton selecton mode. • “ voice” appears. • to change the call type, push and hold [digital button] for 1 sec. Durng stand-by operaton. Af...

  • Page 37

    34 5 idas operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d transmitting a revive call a revve call allows you to send a sgnal that wll revve the (stunned) staton. Q push [digital button] to enter the applcaton selecton mode. • “ voice” appears. • to change the call type, push and hold [digital but...

  • Page 38

    35 5 idas operation d transmitting a remote monitor call a remote montor call allows you to send a sgnal that requre the targeted staton to transmt the mcrophone audo. Q push [digital button] to enter the applcaton selecton mode. • “ voice” appears. • to change the call type, push and hold [digital ...

  • Page 39

    36 5 idas operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d transmitting a radio check call a rado check call allows you to determne whether the tar- geted staton s turned on, wthn the communcaton range and on channel wthout requrng any acton from the targeted staton user. Q push [digital button] t...

  • Page 40

    37 5 idas operation d transmitting a status message the transcever has the ablty to send a pre-programmed status message. There are 100 status messages that can be sent. Q push [digital button] to enter the applcaton selecton mode. • “ voice” appears. • to change the call type, push and hold [digita...

  • Page 41

    38 5 idas operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d transmitting a message the transcever has the ablty to send a pre-programmed message. There are 10 messages that can be sent on a channel. Q push [digital button] to enter the applcaton selecton mode. • “ voice” appears. • to change the ca...

  • Page 42

    39 5 idas operation d direct message input the optonal hm-152t s requred for ths operaton. Q push [digital button] to enter the applcaton selecton mode. • “ voice” appears. • to change the call type, push and hold [digital button] for 1 sec. Durng stand-by operaton. After changng, the transcever ent...

  • Page 43

    40 5 idas operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 d transmitting a status polling call the transcever can send a sgnal that causes the targeted staton to automatcally transmt ts current status. Q push [digital button] to enter the applcaton selecton mode. • “ voice” appears. • to change the...

  • Page 44

    41 5 idas operation d direct id input dependng on the pre-settng, you can nput the desred id drectly. The optonal hm-152t s requred for ths operaton. Q after enterng the indvdual or talkgroup id selecton mode wth pushng [digital button], push the approprate dgt key, [0] to [9], to nput the desred id...

  • Page 45: Position Data Transmission

    42 5 idas operation 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 important: it s recommended to set an emergency channel ndvdually to provde the certan emergency call operaton. Note: when the call type s set to “indvdual,” and the dgtal request ack functon s actvated, the transcever trans- mts the emergen...

  • Page 46: Status Message Transmission

    43 5 idas operation ■ status message transmission the status message can be transmtted automatcally. The status message s transmtted when; • the transcever s turned on or off - set the status message to be transmtted n ‘power on status’ or ‘power off status’ tem, respectvely. - set the target staton...

  • Page 47

    44 memo 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16.

  • Page 48

    1-1-32 kammnam, hrano-ku, osaka 547-0003, japan a-6565-2ex-t © 2006–2009 icom inc..