Remote control manual vhf fm repeater ifr3000 uhf fm repeater ifr4000 1 remote control function . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-1 remote control setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-2 remote control operation . . . . . . . . . . . . . . . . . . . ...
Remote control function 1 1 1-1 remote control setting d d system control to enable remote control functions the dtmf settings (rx system code, tx system code, dtmf setting, tx code ch (autodial), etc.) must be pre-programmed using cs-fr3000 cloning software. Use cs- fr3000 help screens for descript...
2 remote control operation 1 d d system control command note: all commands must be entered within 10 sec. Of entering a password. It is possible to enter the password and command continuously. Format of command • basic command code the basic command code consists of a fixed 4-digit command code, pre...
3 remote control operation 1 1-3 command table default during during function code normal mode phone patch mode sub code transceiver phone transceiver phone system control exit 0002 ✔ ✔ ✔ † ✔ — repeat start 0003 ✔ ✔ — — — repeat stop 0004 ✔ ✔ — — — tx start 0005 — ✔ ‡ — † ✔ ‡ — tx stop 0006 — — — † ...
4 remote control operation 1 • system control exit turns off “system control standby mode” and returns to normal operating mode. Will also “hang up” the phone line during phone patch operation. • repeat start this command enables repeater operation. This command is not available during phone patch o...
5 remote control operation 1 d d repeat start ( 0003 default) this command is available from both the transceiv- er and phone line. This explanation shows the step by step operation from the transceiver or operation from the phone line when entering the password and command continuously (one after t...
6 remote control operation 1 d d rf power (low) ( 0007 default) this command is available from both the transceiv- er and phone line. This explanation shows the step by step operation from the transceiver or operation from the phone line when entering password and command continuously (one after the...
7 remote control operation 1 d d rf power (high) ( 0008 default) this command is available from both the transceiv- er and phone line. This explanation shows the oper- ation from the transceiver when entering the pass- word and command continuously or step by step operation from the phone line (one ...
8 remote control operation 1 d d rx unit off ( 0009 default) this command is available from the phone line only. This explanation shows the step by step oper- ation. You can carry out the command operation either step by step, or by entering the password and command continuously. Q dial the phone nu...
9 remote control operation 1 d d master enable ( 0013 default) this command is available from both the transceiv- er and phone line. This explanation shows the step by step operation from the transceiver or operation from the phone line when entering the password and command continuously (one after ...
10 remote control operation 1 operation example (continue) d d mch select ( 0017 default) this command is available from both the transceiv- er and phone line. This explanation shows the step by step operation from the transceiver or operation from the phone line when entering the password and comma...
11 remote control operation 1 d d cpu all reset ( 0018 default) this command is available from the phone line only. This explanation shows entering the password and command continuously. This command cannot be performed while repeater is transmitting, therefore you must stop the repeater operation b...
12 remote control operation 1 1-6 operation example for phone patch d d description phone patch function allows communication to a transceiver from a telephone line, or connection to a telephone line from a transceiver. During the phone patch operation, the voice communication is sim- plex. (the mut...
1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan s-6228 i -1us © 2004 icom inc..
