1. DL manuals
  2. Icom
  3. Repeater
  4. IC-FR9010
  5. Instruction Manual

Icom IC-FR9010 Instruction Manual

Manual is about: VHF P25 REPEATER; UHF P25 REPEATER

Summary of IC-FR9010

  • Page 1

    Instruction manual vhf p25 repeater ifr9010 ifr9020 uhf p25 repeater this device complies with part 15 of the fcc rules. Operation is subject to the condition that this device does not cause harm- ful interference..

  • Page 2

    R warning high voltage! Never attach an antenna or internal antenna connector during trans- mission. This may result in an electrical shock or burn. R warning high voltage! Never install the antenna at any place that person touch the an- tenna easily during transmission. This may result in an electr...

  • Page 3

    Icom, icom inc, and the icom logo are registered trademarks of icom incorporated (japan) in japan, the united states, the united kingdom, germany, france, spain, russia and/or other coun- tries. All other products or brands are registered trademarks or trade- marks of their respective holders. Ii sa...

  • Page 4

    Iii votre radio icom produit une énergie électromagnétique de radiofréquences (rf), en mode de transmission. Cette radio est conçue pour un «usage professionnel seulement» et classée comme tel, ce qui signifie qu’elle doit être utilisée uniquement dans le cadre d'un travail par des per- sonnes consc...

  • Page 5

    Iv table of contents forward ................................................................. I important .............................................................. I explicit definitions ............................................ I precautions ...................................................

  • Page 6: 1 Lcd Display

    1 1 lcd display lcd display consists of 4 x 20 characters as shown. Line 1: the incoming rssi with 10 steps line 2: the output power levels with 10 steps line 3: the left 4 letters show channel numbers. The middle 8 letters shows the channel name. (if not programmed, it will be blank.) the right 4 l...

  • Page 7: 4 Control Knob

    222 4 control knob 4.1 volume rotate the knob to change the volume level. The volume level varies from 0 to 34. If the lo- cal speaker is active, the audible beep level will change as the knob is rotated. Figure 1 shows the volume at level 12. Figure 1 4.2 squelch control push the rotary knob once t...

  • Page 8: 7 P25 Ptt Mode

    3 6.1 individual call entry (digital base mode only) push and release [a] repeatedly until “idc-----” is displayed. Push [b], and enter the numerical unit id. To deleted a digit, push the star [ q ] key. Push [b] or [#] to complete entry. Figure 8 shows entry start, when [b] is pushed. Figure 9 show...

  • Page 9

    4 8.2 call alert to send a call alert, push [f] then push [a] or [b] until the selection is displayed, then enter the tar- get id of the radio to alert and push [#]. If the target radio has received the call alert the display should show “ack” (acknowledgement). Figure 12 displays a call alert ack. ...

  • Page 10: 9 P25 Squelch Adjustment

    5 8.8 predefined messages used to send a predefined system message. To send a predefined message, push [f] then push [a] or [b] until the selection is displayed, then enter the target radio id, push [d] and enter a message number and push [#]. The target radio should send and ack if successful. Figu...

  • Page 11: 11 Key-Lock

    6 11 key-lock push [shift] + [8] to enable and disable the key-lock. This symbol shows on the lcd. Key-lock and key- unlock icon is displayed for 2 seconds and then reverts to show the tgid. The [ptt], [mon] and [shift] key are not locked. If [ptt], [mon] and [shift] needs to be locked, select disab...

  • Page 12: 15 P25 Channel Data

    7 15 p25 channel data push [shift] + [ q ] to scroll through the data, [ q ] must be depressed to scroll. 1. Unit id (source address) 2. Rx nac 3. Tx-nac 4. Tgid 5. Emergency alarm rcv 6. Call alert rcv 7. Radio check rcv these functions may be enabled and disabled in the programming software’s “mis...

  • Page 13: 20 Emergency Call Reception

    8 20 emergency call reception the 4th line of the lcd shows the emergency alarm when an emergency call is received. The lcd back light flashes and the audible tone heard from the speaker can be increased or decreased with the vol- ume control. Figure 37 below displays the emergency caller's id 00000...

  • Page 14: Versions

    9 24 displaying the firmware versions both the radio and dsp firmware versions are indi- cated on the lcd after the radio switches on for 2 seconds, unless a “starting message” has been pro- grammed. Figure 39 displays radio and dsp firmware versions. Figure 39 figure 40 shows the programmable start...

  • Page 15: 30 Rs-232 Error Detection

    10 30 rs-232 error detection if the communications between pc and the repeater have trouble, the following messages are shown on the lcd. - overrun error - framing error - parity error - unknown command - data unmatched - send error - answer timeout - receive timeout 31 dsp error detection when ther...

  • Page 16: 32 Option Port Pinout

    11 32 option port pinout 25 pin d-sub connector for remote control is provided on the rear panel of ic-fr9010/fr9020. The functions of each pin are as follows: pin no. Name description i/o levels comments 1 ch 0 lsb external binary channel selection l 0 to +3.3 v dc 0000 is channel 1 2 ch 1 external...

  • Page 17

    12 memo.

  • Page 18

    13 memo.

  • Page 19

    14 memo.

  • Page 20

    1-1-32 kamiminami, hirano-ku, osaka 547-0003, japan a-7090h-1ex-0a printed in japan © 2013 icom inc..