Icom VS-3 Instructions - page 2
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
A-7139W-2EX
Printed in Japan
© 2014 Icom Inc.
Playing music
To play music, the Bluetooth
®
device must correspond to the A2DP profile.
Confirm your Bluetooth
®
device’s profile.
The supplied earphone is not for listening to music.
We recommend that you purchase a third party earphone to listen to music.
Playing or Pausing music
Select the music that you want to play in your mobile de-
q
vice.
Push [PLAY].
w
• While playing music, push [PLAY] to pause.
• While playing music, the LED blinks blue twice every 2 sec-
onds.
Stopping music
While playing or pausing music, push [PLAY] to
➥
stop.
• Music starts from the beginning by pushing the play switch after
the music stops.
Rewind music
While playing or pausing music, push [RWD] to re-
➥
wind.
• While holding down [RWD], the headset continues to rewind.
Forward music
While playing or pausing music, push [FWD] to for-
➥
ward.
• While holding down [FWD], the headset continues to forward.
Playing next music
Push [FWD].
➥
Playing previous music
While stopping music, push [RWD].
➥
• While playing music, the LED blinks twice in blue in every 2
seconds.
LED indicator
[PWR]
[FWD]
[PLAY]
[RWD]
NOTE:
The operation may differ, depending on the Bluetooth
®
de-
vice or music player application.
You may not be able to use some Bluetooth
®
functions, de-
pending on the Bluetooth
®
device.
Initializing the headset
If abnormalities occur on the headset, turn OFF the power,
and then turn it ON again after a few seconds. If the condition
continues, initialize the headset.
Turn OFF the power.
q
• If the power is ON, hold down [PWR] for 3 seconds.
After holding down [PWR] for 2 seconds, simultaneously
w
hold down both [PWR] and [VOL](–) for 10 seconds.
• The LED lights purple, and then turns OFF.
Forced termination
If the headset does not operate normally, try the following to
perform a force power OFF.
Push [RESET].
➥
Functions
The following list shows the VS-3s functions, operation, sound and the LED indications.
Connecting to the transceiver with a Bluetooth
®
unit
Function
Operation
Sound
LED indication
Note
Turning ON the power
Hold down [PWR] for 3 seconds.
Melody sounds
(Scale goes up.)
Blinks blue
Turning OFF the power
Hold down [PWR] for 3 seconds.
Melody sounds
(Scale goes down.)
Turns OFF
Pairing
While the power is OFF, hold down
[PWR] for 6 seconds.
PiPa
–
PiRo
• Alternatively blinks red and blue
while waiting for a connection.
• Blinks blue twice every 3 sec-
onds when the connection is
completed.
Switching to the mobile
device
While using the transceiver con-
nected to a mobile device, hold
down [PWR] for 2 seconds.
Pi
Blinks blue twice
Automatically switch to
the transceiver when the
transceiver receives a
signal.
Transmission
Push [PTT]
—
Alternatively blinks red once and
blue twice every 3 seconds.
Volume up
Push [+]
Long beep
(High tone)
†
Blinks twice in blue
†
Sounds when a maxi-
mum level is selected.
Volume down
Push [–]
Long beep
(Low tone)
‡
Blinks blue twice
‡
Sounds when a mini-
mum level is selected.
Increase the MIC gain*
1
Push [+] while holding down [PTT]. PiPiPi
—
Decrease the MIC gain*
1
Push [–] while holding down [PTT]. Pi
—
Changing the frequency,
Memory or Call channel.*
2
Switching between FROM
and TO selection.*
2
Up: Push [
]
Down: Push [
]
Pi
Blinks blue twice
Select the item in the op-
erating screen.
Play/Pause*
2
Push [
≈‘
]
Pi
Blinks blue twice
Forward*
2
Push [
]
Pi
Blinks blue twice
Rewind*
2
Push [
]
Pi
Blinks blue twice
Forcibly shutdown
Push [RESET]
—
Turns OFF
Charging
Refer to instruction manual
q
—
Lights red
When the connection is disconnected from the transceiver, two beeps sound.
*
1
The MIC gain has three levels. When the level 3 is selected, 3 beeps sound, the level 2 is selected, 2 beeps sound, and the level 1 is selected,
a bees sounds.
*
2
You can assign these key functions from the transceiver.
[RESET]
Connecting to the Bluetooth
®
mobile device
Function
Operation
Sound
LED indication
Note
Turning ON the power
Hold down [PWR] for 3 seconds.
Melody sounds
(Scale goes up.)
Blinks blue
Turning OFF the power
Hold down [PWR] for 3 seconds.
Melody sounds
(Scale goes down.)
Turns OFF
Pairing
While the power is OFF, hold down
[PWR] for 6 seconds.
PiPa
–
PiRo
• Alternatively blinks red and blue
while waiting for a connection.
• Blinks blue twice every 3 sec-
onds when the connection is
completed.
Switching to the trans-
ceiver
Push [PTT].
Pi
Making a call
Push the power switch
Receiving a call
Push the power switch
—
Blinks blue twice every 3 sec-
onds.
Disconnecting a call
Push the power switch
Volume up
Push [+]
Long beep
(High tone)
†
Blinks blue twice.
†
Sounds when a maxi-
mum level is selected.
Volume down
Push [–]
Long beep
(Low tone)
‡
Blinks blue twice.
‡
Sounds when a mini-
mum level is selected.
Play/Pause
Push [
≈‘
]
Pi
Blinks blue twice.
Stop
Push [
≈‘
]
Forward
Push [
]
Pi
Blinks blue twice.
Rewind
Push [
]
Pi
Blinks blue twice.
Forcibly shutdown
Push [RESET]
—
Turns OFF.
Charging
Refer to the instruction manual
q
—
Lights red.
When the VS-3 is connected to both a paired transceiver and the mobile device, the transceiver has priority. However, when you push [PWR]
while operating the transceiver, the connection switches to the mobile device. Pushing [PTT] returns to the transceiver connection.
[VOL](
–
)
[PWR]
[PWR]
After holding down
for 2 seconds
Hold down for
10 seconds
LED indicator